2 When a multi-path system is used, the setting for path 1 is followed.
#7 #6 #5 #4 #3 #2 #1 #0
3291 WPT
[Input type] Parameter input [Data type] Bit path
#0 WPT The input of the tool wear compensation amount is:
0: Enabled according to memory protection signal KEY1 <Gn046.3>.
1: Enabled, regardless of the memory protection signal KEY1 <Gn046.3>.
3294 Start number of tool offset values whose input by MDI is disabled
3295 Number of tool offset values (from the start number) whose input by MDI is disabled
[Input type] Parameter input [Data type] Word path [Valid data range] 0 to 999
When the modification of tool offset values by MDI key input is to be disabled using bits 0 (WOF) and 1 (GOF) of parameter No. 3290, parameters Nos. 3294 and 3295 are used to set the range where such modification is disabled. In parameter No. 3294, set the offset number of the start of tool offset values whose modification is disabled. In parameter No.
3295, set the number of such values. In the following cases, however, none of the tool offset values may be modified:
- When 0 or a negative value is set in parameter No. 3294 - When 0 or a negative value is set in parameter No. 3295
- When a value greater than the maximum tool offset number is set in parameter No.
3294
In the following case, a modification to the values ranging from the value set in parameter No. 3294 to the maximum tool offset number is disabled:
- When the value of parameter No. 3294 added to the value of parameter No. 3295 exceeds the maximum tool offset number
When the offset value of a prohibited number is input through the MDI panel, the warning "WRITE PROTECT" is issued.
[Example] When the following parameter settings are made, modifications to both of the tool geometry offset values and tool wear offset values corresponding to offset numbers 51 to 60 are disabled:
- Bit 1 (GOF) of parameter No. 3290 = 1 (to disable tool geometry offset value modification)
- Bit 0 (WOF) of parameter No. 3290 = 1 (to disable tool wear offset value modification)
- Parameter No. 3294 = 51 - Parameter No. 3295 = 10
If the setting of bit 0 (WOF) of parameter No. 3290 is set to 0 without modifying the other parameter settings above, tool geometry offset value modification only is disabled, and tool wear offset value modification is enabled.
#7 #6 #5 #4 #3 #2 #1 #0
3299 PKY
[Input type] Setting input [Data type] Bit
#0 PKY "Parameter write enable" is:
0: Set on the setting screen (bit 0 (PWE) of setting parameter No. 8900).
1: Set by the memory protection signal KEYP<G046.0>.
#7 #6 #5 #4 #3 #2 #1 #0
3301 HDC HCN H16
[Input type] Parameter input [Data type] Bit path
#0 H16 Bit map data of screen hard copies uses:
0: 256 colors.
1: 16 colors.
#4 HCN Bit map file name of the screen hard copy is:
0: “HDCPYxxx.BMP”
(xxx(000~999) means the number of screen hard copy after power-on) 1: “YYMMDDxx.BMP”
(YY(00~99) means the year, MM(01~12) means the month, DD(01~31) means the day and xx(00~99) means the number of screen hard copy in that day)
#7 HDC A screen hard copy function is:
0: Disabled.
1: Enabled.
3321 Screen number assigned to the 1st vertical soft key
to to
3336 Screen number assigned to the 16th vertical soft key
[Input type] Parameter input [Data type] Word
[Valid data range] 1 to 10000
Assign a screen number to be displayed as a shortcut to a vertical soft key.
The 1st to 8th vertical soft keys are displayed on page 1, and the 9th to 16th vertical soft keys are displayed on page 2.
When specifying page 2, be sure to specify "Display of next page" on each page.
When not specifying page 2, set 0 for the 9th to 16th soft keys.
In this case, page 2 is not used, so that "Display of next page" need not be specified on page 1.
If all of these parameters are 0 when turning on the power supply, one-touch menu of the default table is displayed.
NOTE
1 When screen numbers are specified in at least one of CNC parameters Nos. 3321 to 3336, the setting is valid. In the case, nothing is displayed in the vertical soft-key where 0 is specified in the parameter.
2 In order to display the default one-touch menu again, it is needed to turn off power after all of these parameters are set to 0.
(1) CNC operation screens
Screen No. Screen name Screen No. Screen name
99 Display of next page(*1) 143 Spindle setting
100 Absolute position display(*2) 144 Spindle adjustment 101 Relative position display(*2) 145 Spindle monitor 102 Overall position display(*2) 146 FSSB amplifier setting 103 Overall position display(*3) 147 FSSB axis setting
104 Handle screen 148 FSSB amplifier maintenance
105 Monitor screen 149 Servo setting
106 3-dimensional manual feed 150 Servo adjustment
107 Program 151 Periodic maintenance: State
108 Program directory display 152 Periodic maintenance: Machine
109 Next block 153 Periodic maintenance: NC
110 Program check 154 8-level data protection: Operation level
setting
111 Time display 155 8-level data protection: Password change
112 Manual value specification 156 8-level data protection: Protection level setting
Screen No. Screen name Screen No. Screen name
113 Program restart 157 Protection against wrong operations
114 Offset display 158 Protection against wrong operations
Offset range setting screen
115 Setting parameter 159
Protection against wrong operations External workpiece origin offset range setting screen
116 Coordinate system display 160
Protection against wrong operations Workpiece origin offset range setting screen
117 Software operator's panel 161 Protection against wrong operations Y-axis offset range setting screen
118 Y-axis offset 162 Protection against wrong operations
Workpiece shift range setting screen 119 Workpiece coordinate system shift 163 Servo guide: Y-TIME
120 Second geometry offset 164 Servo guide: XY
121 Tool geometry data 165 Servo guide: CIRCLE
122 Precision level 166 Servo guide: FOURIER
123 Chopping 167 Servo guide: BODE
124 Chuck/tail 168 Servo guide: Channel setting
125 Language 169 Alarm: Details
126 Parameter 170 Alarm: All paths
127 Diagnosis 171 Waveform diagnosis: Graph
128 System configuration 172 Waveform diagnosis: Parameter
129 Memory contents display 173 Operation history
130 Pitch error compensation 174 Operation history signal selection
131 Machining adjustment 175 Cartridge management
132 Color setting 176 Tool management
133 Maintenance information 177 Power Mate CNC manager: Absolute coordinates
134 Touch panel calibration(*2) 178 Power Mate CNC manager: Machine coordinates
135 Parameter adjustment 179 Power Mate CNC manager: Parameter
136 Ｍ code group 180 Power Mate CNC manager: Message
137 3-dimensional error compensation 181 Power Mate CNC manager: Diagnosis 138 External operator message 182 Power Mate CNC manager: System
configuration
139 Alarm history 183 Macro: Custom
140 External operator message history 184 Macro: Execution
141 Drawing parameter 185 Macro: Conversation
142 Tool path drawing 186 Macro: Auxiliary
*1 Definition for feeding vertical soft key pages
*2 Specifiable with a 10.4-inch display unit only
*3 Specifiable with a 15/19-inch display unit only
(2) PMC operation screens (3) Communication operation screens
Screen No. Screen name Screen No. Screen name
200 PMC signal status Ethernet setting
201 PMC IO link 300 [Built-in port] Common
202 PMC alarm 301 [Built-in port] FOCAS2/Ethernet
203 PMC input/output 302 [Built-in port] FTP transfer
204 PMC timer 303 [Built-in port] PING
205 PMC counter 304 [Built-in port] Communication state
206 PMC keep relay 305 [Built-in port] Task state
207 PMC data table 306 [PCMCIA] Common
208 PMC trace 307 [PCMCIA] FOCAS2/Ethernet
209 PMC trace setting 308 [PCMCIA] FTP transfer
210 PMC program directory display 309 [PCMCIA] PING
211 PMC ladder diagram display 310 [PCMCIA] Communication state
Screen No. Screen name Screen No. Screen name
212 PMC title setting 311 [PCMCIA] Task state
213 PMC configuration parameter setting 312 [Board] Common
214 PMC general setting 313 [Board] FOCAS2/Ethernet
215 PMC status 314 [Board] Data server
216 PMC system parameter 315 [Board] PING
217 PMC IO assignment 316 [Board] Communication state
218 PMC symbol 317 [Board] Task state 323 [Built-in/PCMCIA] FTP transfer Profibus setting
324 [MASTER] Overall 325 [MASTER] Bus parameter 326 [MASTER] Slave table
327 [MASTER] Communication state 328 [MASTER] Slave parameter 329 [MASTER] Module data 330 [MASTER] DI/DO address 331 [MASTER] Mode
(4) ALL I/O Screen (5) CNC screens
Screen No.
Screen name Screen No. Screen name
400 ALLIO Program(*1) 500 Dual Check Safety MCC Off Test
401 ALLIO Parameter(*1) 501 Dual Check Safety Cross Check
402 ALLIO Offset(*1) 502 Dual Check Safety Flow Monitoring
403 ALLIO Macro(*1) 503 Dual Check Safety Feed Limit
404 ALLIO Pitch Error Compensation(*1) 504 Dual Check Safety Machine Positioning 405 ALLIO Workpiece Coordinate(*1) 505 Dual Check Safety Position Error
406 ALLIO Y-axis Offset(*1) 506 Dual Check Safety Brake Test
407 ALLIO Second Geometry Offset(*1) 507 Dual Check Safety FL-net
408 ALLIO Tool Management(*1) 508 Tool Life Management
409 ALLIO Tool Management (Magazine) (*1) 509 Robot Status 410 ALLIO Tool Management (Custom) (*1) 510 Robot Connect 411 ALLIO Tool Management (Status) (*1) 511 Power Consumption 412 ALLIO Operation History(*1) 512 Offset Wear/Wear1/Offset-1
413 ALLIO Tool Geometry(*1) 513 Offset Geometry/Geometry1/Offset-2 416 ALLIO Maintenance Information(*1) 514 Offset Wear2
515 Offset Geometry2 516 Fan monitor
517 Leakage detection monitor 518 Detector monitor
*1 The screen for RS-232C or memory card is displayed by setting I/O Devices.
4.21 PARAMETERS OF PROGRAMS (1 OF 4)
#7 #6 #5 #4 #3 #2 #1 #0
3400 SMX PGD MGC MGO
[Input type] Parameter input [Data type] Bit path
#0 MGO If the program restart M/S/T/B code output function is used:
0: When bit 6 (MOA) of parameter No. 7300 is set to 0, the last M code only is output.
When bit 6 (MOA) of parameter No. 7300 is set to 1, M codes are output in a specified order.
1: When bit 6 (MOA) of parameter No. 7300 is set to 0, the last M code of each M code group is output in the order of groups.
When bit 6 (MOA) of parameter No. 7300 is set to 1, M codes are output in the order of groups.
NOTE