Menu Phone Setup

Headset: Off Direct Dial...

Lock Phone...

Change PIN...

LCD Contrast: 7 LCD Light: On

< Phone Setup

Figure 90: Menu Phone Setup (1. Part) Keypad Light: On

< Phone Setup

Figure 91: Menu Phone Setup (2. Part)

3.9.1 Headset

Setup headset, switching on and off

1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

3. Press the key . The display appears in Figure 90.

4. Use the arrow keys to select the line Headset.

5. If you press the key at this point, you can switch between "On" und "Off". If a headset is connected to the telephone, the headset can be enabled.

3.9.2 Direct Dial

Setup direct dial, switching on and off 1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

4. Use the arrow keys to select the menu Do not disturb.

5. Press the key . The display appears in Figure 92.

Direct dial: Off Number:

Delay (seconds): 0

+ Direct dial

Figure 92: Menu Direct dial

6. Use the cursor keys to select the line Direct dial.

7. If you press the key at this point, you can switch between "On" and "Off".

8. Use the cursor keys to select the line Number.

9. Enter the desired Direct dial number.

10. Use the cursor keys to select the line Delay.

11. Enter the delay in seconds. Valid values are between 0 and 65535 seconds.

12. In order to store the selection, leave the menu by pressing the key three times.

The set direct call is now active and is not indicated in the display of the telephone.

If you set a delay t > 0 seconds after picking up the receiver, you have t seconds to make a call. Only when this time has expired, the programmed telephone number will be dialled.

Note

If the direct dial is active and the delay is set to 0 seconds, then after the try to enter digits in the idle state the following error message will be displayed: keyboard locked!

Also with active direct dial no inquiry calls can be made.



3.9.3 Lock Phone

Setup lock phone, switching on and off 1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

3. Press the key . The display appears in Figure 90.

4. Use the arrow keys to select the menu Lock Phone.

5. Press the key . The display appears in Figure 93.

Please enter PIN PIN:

< Authentication

Figure 93: Menu Authentication

6. Enter the PIN and confirm the entry by pressing the key. Each entered digit is shown as * in the display.

7. If the entered PIN is not valid, the message in Figure 94: is shown briefly. The screen in Figure 93 appears again.

PIN invalid

Figure 94: Menu PIN Invalid

8. If the entered PIN is valid, the message in Figure 95 is shown briefly. Thereafter, the device is in its initial condition. A display message indicates that the device is locked.

Attention

no emergency calls possible!

<

Figure 95: Menu Authentication PIN Valid

9. If the device is locked, and you press one of the keys , , , , , , (short or long), (long) or some programmed function keys the message in Figure 93: Menu Authentication appears. Enter the PIN and confirm the entry by pressing the key.

10. If the PIN entry is correct, the device is unlocked and in its initial condition.

11. If the entered PIN is not correct, the message in Figure 94: appears briefly. Then the message in Figure 93: Menu Authentication appears again.

3.9.4 Change PIN

1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

3. Press the key . The display appears in Figure 90.

4. Use the arrow keys to select the menu Change PIN.

5. Press the key . The display appears in Figure 96.

Cur PIN:

New PIN:

New PIN:

< Change PIN

Figure 96: Menu Change PIN 6. Enter the old PIN.

7. Press the key to go to the next line.

8. Enter the new PIN. Allowed are the characters 0 – 9, *, #. The PIN can be 0 – 12 characters long.

9. Press the key to go to the next line.

10. Enter the new PIN one more time.

11. Press the key to confirm the entry.

12. If the entered PIN change is valid, the message in Figure 95 is shown briefly.

Then the screen in Figure 58 appears.

Changes activated

Figure 97: Menu Changes Activated

13. If the entered PIN change is not valid, the message in Figure 94 is shown briefly.

Then the screen in Figure 96 appears.

3.9.5 LCD Contrast

1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

3. Press the key . The display appears in Figure 90.

4. Use the arrow keys to select the menu LCD Contrast.

5. With the keys und you can change the LCD contrast.

3.9.6 LCD Light

1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

5. If you press the key at this point, you can switch between "On" und "Off".

3.9.7 Keypad Light

This feature is only available for telephones with an illuminated keypad.

1. In the initial condition press the key or .

2. Use the arrow keys to select the menu Phone Setup.

3. Press the key . The display appears in Figure 90.

4. Use the arrow keys to select the menu Keypad Light.

5. If you press the key at this point, you can switch between "On" und "Off".