Procedures of IU CS Configuration (IP)

6.4.1 IP Addresses Planning

Note: This section describes the IP address planning by using the GOU board in Slot 14 in Subrack 0 as an example. Figure 6-4 shows specific IP addresses.

G O U FE IP : 10 .210 .1 .52 Router M G W Gateway IP : 10 .210 .1 .49 /29 User IP : 10 .210 .1 .37 DEV IP : 10 .210 .1 .4 5 /30 (Sig ) 10 .210 .1 .4 1 /30 (User ) M S C Sig IP : 10 .210 .1 .69

Figure 1.30 IUCS data planning

6.4.2 Configuration of Physical Layer Data

For configurations of other boards such as UOI, POU, and PEU, see the initial configuration guide.

//Run SET ETHPORT to set the Ethernet port attributes.

SET ETHPORT: SRN=0, SN=14, BRDTYPE=GOU, PN=0, MTU=1500, AUTO=DISABLE, FC=OFF, OAMFLOWBW=0, FLOWCTRLSWITCH=ON, FCINDEX=0;

//Run ADD ETHIP to add the IP address of the Ethernet port.

ADD ETHIP: SRN=0, SN=14, PN=0, IPTYPE=SECOND, IPINDEX=1, IPADDR="10.210.1.52", MASK="255.255.255.248";

// (Optional) Run ADD DEVIP to add the device IP address of the board.

ADD DEVIP: SRN=0, SN=14, IPADDR="10.210.1.45", MASK="255.255.255.252"; ADD DEVIP: SRN=0, SN=14, IPADDR="10.210.1.41", MASK="255.255.255.252"; Note: The device IP is used as the local address of the SCTPLNK and IPPATH.

6.4.3 Adding Control Plane Data of Iu-CS Interface

(OPC --> N7DPC )--> M3LE --> M3DE --> M3LKS --> M3RT --> M3LNK

//Run ADD SCTPLNK to add one SCTP signaling link. To add more SCTP links, run the command for multiple times. Set Work mode to Client/SERVER (the RNC is Client). Set Application Type to M3UA.

ADD SCTPLNK:SRN=0, SN=2, SSN=0, SCTPLNKN=0, MODE=CLIENT, APP=M3UA,

DSCP=62, LOCPTNO=5000, LOCIPADDR1="10.210.1.45",

PEERIPADDR1="10.210.1.69", PEERPORTNO=5000, LOGPORTFLAG=NO, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25, HBINTER=1000, MAXASSOCRETR=4, MAXPATHRETR=2, CHKSUMTX=NO, CHKSUMRX=NO, CHKSUMTYPE=CRC32, MTU=1500, VLANFLAG=ENABLE,

VLANID=102, CROSSIPFLAG=UNAVAILABLE, SWITCHBACKFLAG=YES,

SWITCHBACKHBNUM=10;

ADD SCTPLNK:SRN=0, SN=2, SSN=1, SCTPLNKN=1, MODE=CLIENT, APP=M3UA,

DSCP=62, LOCPTNO=5002, LOCIPADDR1="10.210.1.45",

PEERIPADDR1="10.210.1.69", PEERPORTNO=5002, LOGPORTFLAG=NO, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25, HBINTER=1000, MAXASSOCRETR=4, MAXPATHRETR=2, CHKSUMTX=NO, CHKSUMRX=NO, CHKSUMTYPE=CRC32, MTU=1500, VLANFLAG=ENABLE,

VLANID=102, CROSSIPFLAG=UNAVAILABLE, SWITCHBACKFLAG=YES,

SWITCHBACKHBNUM=10;

//Run ADD N7DPC to add one DPC. To add more DPCs, run the command for multiple times.

ADD N7DPC: DPX=0, DPC=H'000972, SLSMASK=B0000, NEIGHBOR=YES, NAME="MSC1", DPCT=IUCS_RANAP, STP=OFF, PROT=ITUT, BEARTYPE=M3UA; ADD N7DPC: DPX=1, DPC=H'000973, SLSMASK=B0000, NEIGHBOR=YES, NAME="MGW4M01", DPCT=IUCS_ALCAP, STP=OFF, PROT=ITUT, BEARTYPE=M3UA; //Run ADD M3LE to add one M3UA local entity.

ADD M3LE: LENO=0, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="RNC4M01";

//Run ADD M3DE to add one M3UA destination entity.

ADD M3DE: DENO=0, LENO=0, DPX=0, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="IUCS-MSC1";

//Run ADD M3LKS to add the M3UA link set.

ADD M3LKS: SIGLKSX=0, DENO=0, LNKSLSMASK=B1111,

TRAMODE=M3UA_LOADSHARE_MOD, WKMODE=M3UA_IPSP, PDTMRVALUE=5, NAME="IUCS-MSC1";

Note: To implement the signaling route load sharing, it is recommended that Signaling Route Mask should be set to B1000 by running the command ADD N7DPC. Signaling Link Mask should be set to B0111 by running the command ADD M3LKS.

ADD M3RT: DENO=0, SIGLKSX=0, PRIORITY=0, NAME="IUCS-RANP1";

//Run ADD M3LNK to add the M3UA link. To add more M3UA links, run the command for multiple times.

ADD M3LNK:SIGLKSX=0, SIGLNKID=0, SRN=0, SN=2, SSN=0, SCTPLNKN=0, PRIORITY=0, LNKREDFLAG=M3UA_MASTER_MOD, NAME="CS1-0";

ADD M3LNK:SIGLKSX=0, SIGLNKID=1, SRN=0, SN=2, SSN=1, SCTPLNKN=1, PRIORITY=0, LNKREDFLAG=M3UA_MASTER_MOD, NAME="CS1-1";

//Run ADD ADJNODE to add one transport neighbor node. Set Node type to IUCS, Transport type to IP.

ADD ADJNODE: ANI=1700, NAME="MGW4M01", NODET=IUCS, DPX=1, TRANST=IP; //Run ADD CNDOMAIN to add the CN domain. Set CN Domain Flag to CS_DOMAIN. ADD CNDOMAIN: CNDOMAINID=CS_DOMAIN, T3212=10, ATT=ALLOWED, DRXCYCLELENCOEF=6;

//Run ADD CNNODE to add the CN node. Set CN domain Flag to CS_DOMAIN. Set IU trans bearer type to IP_TRANS.

ADD CNNODE: CNOPINDEX=0, CNID=1, CNDOMAINID=CS_DOMAIN, DPX=0,

CNPROTCLVER=R5, SUPPORTCRTYPE=CR529_SUPPORT,

CNLOADSTATUS=NORMAL, AVAILCAP=1000, TNLBEARERTYPE=IP_TRANS, RTCPSWITCH=OFF;

6.4.4 Adding the Mapping Relation of Transport Resources of Neighbor

Nodes

//Run ADD TRMMAP to add one mapping relation record between the transport and service. To add more mapping records, run the command for multiple times.

ADD TRMMAP:TMI=1, ITFT=IUB_IUR_IUCS, TRANST=IP, EFDSCP=46, AF43DSCP=38, AF42DSCP=36, AF41DSCP=34, AF33DSCP=30, AF32DSCP=28, AF31DSCP=26, AF23DSCP=22, AF22DSCP=20, AF21DSCP=18, AF13DSCP=14, AF12DSCP=12, AF11DSCP=10, BEDSCP=0, CCHPRIPATH=HQ_IPRT, CCHSECPATH=NULL,

SRBPRIPATH=HQ_IPRT, SRBSECPATH=NULL, VOICEPRIPATH=HQ_IPRT,

VOICESECPATH=NULL, CSCONVPRIPATH=HQ_IPRT, CSCONVSECPATH=NULL,

CSSTRMPRIPATH=HQ_IPRT, CSSTRMSECPATH=NULL,

PSCONVPRIPATH=HQ_IPRT, PSCONVSECPATH=NULL, PSSTRMPRIPATH=HQ_IPRT,

PSSTRMSECPATH=NULL, PSHIGHINTERACTPRIPATH=HQ_IPNRT,

PSHIGHINTERACTSECPATH=NULL, PSMIDINTERACTPRIPATH=HQ_IPNRT,

PSMIDINTERACTSECPATH=NULL, PSLOWINTERACTPRIPATH=HQ_IPNRT,

PSLOWINTERACTSECPATH=NULL, PSBKGPRIPATH=HQ_IPNRT,

HDCONVPRIPATH=HQ_IPHDRT, HDCONVSECPATH=NULL, HDSTRMPRIPATH=HQ_IPHDNRT, HDSTRMSECPATH=NULL, HDHIGHINTERACTPRIPATH=HQ_IPHDNRT, HDHIGHINTERACTSECPATH=NULL, HDMIDINTERACTPRIPATH=HQ_IPHDNRT, HDMIDINTERACTSECPATH=NULL, HDLOWINTERACTPRIPATH=HQ_IPHDNRT, HDLOWINTERACTSECPATH=NULL, HDBKGPRIPATH=HQ_IPHDNRT, HDBKGSECPATH=NULL, HUSRBPRIPATH=HQ_IPHURT, HUSRBSECPATH=NULL, HUCONVPRIPATH=HQ_IPHURT, HUCONVSECPATH=NULL, HUSTRMPRIPATH=HQ_IPHURT, HUSTRMSECPATH=NULL, HUHIGHINTERACTPRIPATH=HQ_IPHUNRT, HUHIGHINTERACTSECPATH=NULL, HUMIDINTERACTPRIPATH=HQ_IPHUNRT, HUMIDINTERACTSECPATH=NULL, HULOWINTERACTPRIPATH=HQ_IPHUNRT, HULOWINTERACTSECPATH=NULL, HUBKGPRIPATH=HQ_IPHUNRT, HUBKGSECPATH=NULL; //Run ADD FACTORTABLE to add one activity factor record.

Note: The two items are mandatory. The two items are required by running the command ADD ADJMAP.

ADD FACTORTABLE:FTI=1, REMARK="IUCS", GENCCHDL=70, GENCCHUL=70, MBMSCCHDL=100, SRBDL=15, SRBUL=15, VOICEDL=70, VOICEUL=70,

CSCONVDL=100, CSCONVUL=100, CSSTRMDL=100, CSSTRMUL=100,

PSCONVDL=70, PSCONVUL=70, PSSTRMDL=100, PSSTRMUL=100, PSINTERDL=100, PSINTERUL=100, PSBKGDL=100, PSBKGUL=100, HDSRBDL=50, HDCONVDL=70, HDSTRMDL=100, HDINTERDL=100, HDBKGDL=100, HUSRBUL=50, HUCONVUL=70, HUSTRMUL=100, HUINTERUL=100, HUBKGUL=100;

//Run ADD ADJMAP to add one activity factor record to configure the corresponding transport resource mapping table for different levels of subscribers, and configure the activity factor table.

ADD ADJMAP: ANI=1700, CNMNGMODE=SHARE, TMIGLD=1, TMISLV=1, TMIBRZ=1, FTI=1;

6.4.5 Adding User Plane Data of Iu-CS Interface

//Run ADD PORTCTRLER to add transport resources for the designated port to manage and control the SPUa subsystem.

ADD PORTCTRLER: SRN=0, SN=14, PT=ETHER, CARRYEN=0, CTRLSN=2,

CTRLSSN=0, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0,

BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0;

//Run ADD IPPATH to add one IP PATH. To add more IP PATHs, run the command for multiple times.

PEERIPADDR="10.210.1.37", PEERMASK="255.255.255.248", TXBW=1000000, RXBW=1000000, DSCP=46, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0, VLANFLAG=ENABLE, VLANID=101, PATHCHK=ENABLED, ECHOIP="10.210.1.37", PERIOD=5, CHECKCOUNT=5, ICMPPKGLEN=64;

//Run ADD IPRT to add the IP route (it is configured when L3 networking is used between the RNC and the CS).

//Add the user plane route.

ADD IPRT: SRN=0, SN=14, DESTIP="10.210.1.32", MASK="255.255.255.248", NEXTHOP="10.210.1.49", PRIORITY=HIGH, REMARK="MGW4M01";

//Add the signaling plane route.

ADD IPRT: SRN=0, SN=14, DESTIP="10.210.1.64", MASK="255.255.255.248", NEXTHOP="10.210.1.73", PRIORITY=HIGH, REMARK="MSC1";