Procedures of IUR Configuration (IP)

6.5.1 IP Addresses Planning

Note: This section describes the IP address planning by taking the GOU board in Slot16 of Subrack 0 as an example.

G

O

U

FE IP: 172.18.62.65/29 Router

G

O

U

Gateway IP: 172.18.62.70/29 Other RNC FE IP: 172.18.30.65/29

Figure 1.31 IUR data planning

6.5.2 Configuration of Physical Layer Data

For configurations of other boards such as UOI, POU, and PEU, see the initial configuration guide.

//Run SET ETHPORT to set the Ethernet port attributes.

SET ETHPORT: SRN=0, SN=16, BRDTYPE=GOU, PN=0, MTU=1500, AUTO=ENABLE, OAMFLOWBW=0, FLOWCTRLSWITCH=ON, FCINDEX=0;

//Run ADD ETHIP to add the IP address of the Ethernet port.

ADD ETHIP: SRN=0, SN=16, PN=0, IPTYPE=PRIMARY, IPADDR="172.18.62.65", MASK="255.255.255.248";

// (Optional) Run ADD DEVIP to add the device IP address of the board.

Note: The device IP is used as the local address of the SCTPLNK and IPPATH.

6.5.3 Adding Control Plane Data of Iur Interface

General configuration procedures:

(OPC --> N7DPC)--> M3LE --> M3DE --> M3LKS --> M3RT --> M3LNK

//Run ADD SCTPLNK to add one SCTP signaling link. To add more SCTP links, run the command for multiple times. Set Work mode to Client/SERVER (the RNC is Client). Set Application Type to M3UA.

ADD SCTPLNK:SRN=0, SN=2, SSN=3, SCTPLNKN=0, MODE=SERVER, APP=M3UA, DSCP=62, LOCIPADDR1="172.18.62.65", PEERIPADDR1="172.18.30.65", PEERPORTNO=9000, LOGPORTFLAG=NO, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25, HBINTER=1000, MAXASSOCRETR=4, MAXPATHRETR=2, CHKSUMTX=NO, CHKSUMRX=NO, CHKSUMTYPE=CRC32,

MTU=1500, VLANFLAG=DISABLE, CROSSIPFLAG=UNAVAILABLE,

SWITCHBACKFLAG=YES, SWITCHBACKHBNUM=10;

//Run ADD N7DPC to add one DPC. For the type, select the IUR interface.

ADD N7DPC: DPX=11, DPC=H'000579, SLSMASK=B0000, NEIGHBOR=YES, NAME="HW RNC11", DPCT=IUR, STP=OFF, PROT=ITUT, BEARTYPE=M3UA;

//Run ADD NRNC to add the neighbor RNC information.

ADD NRNC: NRNCID=11, SHOTRIG=CS_SHO_SWTICH-1&HSPA_SHO_SWITCH-

1&NON_HSPA_SHO_SWTICH-1, HHOTRIG=OFF,

SERVICEIND=SUPPORT_CS_AND_PS, IUREXISTIND=TRUE, DPX=11,

RNCPROTCLVER=R6, STATEINDTMR=20, SUPPIURCCH=NO,

HHORELOCPROCSWITCH=DL_DCCH_SWITCH-0&IUR_TRG_SWITCH-0,

TNLBEARERTYPE=IP_TRANS, DSCRIND=FALSE, IURHSDPASUPPIND=OFF, IURHSUPASUPPIND=OFF;

ADD M3DE: DENO=11, LENO=0, DPX=11, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="RNC11 DE";

//Run ADD M3LKS to add the M3UA link set. To implement the M3UA link load sharing, set Signaling Link Mask to B0111.

ADD M3LKS: SIGLKSX=11, DENO=11, LNKSLSMASK=B1111,

TRAMODE=M3UA_LOADSHARE_MOD, WKMODE=M3UA_IPSP, PDTMRVALUE=5, NAME="RNC12 To RNC 11";

Note: To implement the signaling route load sharing, it is recommended that Signaling Route Mask should be set to B1000 by running the command ADD N7DPC. Signaling Link Mask should be set to B0111 by running the command ADD M3LKS.

//Run ADD M3RT to add the M3UA route.

ADD M3RT: DENO=11, SIGLKSX=11, PRIORITY=0, NAME="M3RT BETWEEN RNC12 AND RNC 11";

//Run ADD M3LNK to add the M3UA link. To add more M3UA links, run the command for multiple times.

ADD M3LNK:SIGLKSX=11, SIGLNKID=0, SRN=0, SN=2, SSN=3, SCTPLNKN=0, PRIORITY=0, LNKREDFLAG=M3UA_MASTER_MOD, NAME="Route from RNC12 To RNC11";

6.5.4 Adding the Mapping Relation of Transport Resources of Neighbor

Nodes

//Run ADD ADJNODE to add one transport neighbor node. Set Node type to IUCS, Transport type to IP.

ADD ADJNODE: ANI=11, NAME="to ROC_RNC11", NODET=IUR, DPX=11, TRANST=IP; Adding the Mapping Relation of Transport Resources of Neighbor Nodes

//Run ADD TRMMAP to add one mapping relation record between a transport and a service. To add more mapping records, run the command for multiple times.

ADD TRMMAP:TMI=1, ITFT=IUB_IUR_IUCS, TRANST=IP, EFDSCP=46, AF43DSCP=38, AF42DSCP=36, AF41DSCP=34, AF33DSCP=30, AF32DSCP=28, AF31DSCP=26, AF23DSCP=22, AF22DSCP=20, AF21DSCP=18, AF13DSCP=14, AF12DSCP=12, AF11DSCP=10, BEDSCP=0, CCHPRIPATH=HQ_IPRT, CCHSECPATH=NULL,

SRBPRIPATH=HQ_IPRT, SRBSECPATH=NULL, VOICEPRIPATH=HQ_IPRT,

VOICESECPATH=NULL, CSCONVPRIPATH=HQ_IPRT, CSCONVSECPATH=NULL,

CSSTRMPRIPATH=HQ_IPRT, CSSTRMSECPATH=NULL,

PSCONVPRIPATH=HQ_IPRT, PSCONVSECPATH=NULL, PSSTRMPRIPATH=HQ_IPRT,

PSHIGHINTERACTSECPATH=NULL, PSMIDINTERACTPRIPATH=HQ_IPNRT,

PSMIDINTERACTSECPATH=NULL, PSLOWINTERACTPRIPATH=HQ_IPNRT,

PSLOWINTERACTSECPATH=NULL, PSBKGPRIPATH=HQ_IPNRT,

PSBKGSECPATH=NULL, HDSRBPRIPATH=HQ_IPHDRT, HDSRBSECPATH=NULL,

HDCONVPRIPATH=HQ_IPHDRT, HDCONVSECPATH=NULL, HDSTRMPRIPATH=HQ_IPHDNRT, HDSTRMSECPATH=NULL, HDHIGHINTERACTPRIPATH=HQ_IPHDNRT, HDHIGHINTERACTSECPATH=NULL, HDMIDINTERACTPRIPATH=HQ_IPHDNRT, HDMIDINTERACTSECPATH=NULL, HDLOWINTERACTPRIPATH=HQ_IPHDNRT, HDLOWINTERACTSECPATH=NULL, HDBKGPRIPATH=HQ_IPHDNRT, HDBKGSECPATH=NULL, HUSRBPRIPATH=HQ_IPHURT, HUSRBSECPATH=NULL, HUCONVPRIPATH=HQ_IPHURT, HUCONVSECPATH=NULL, HUSTRMPRIPATH=HQ_IPHURT, HUSTRMSECPATH=NULL, HUHIGHINTERACTPRIPATH=HQ_IPHUNRT, HUHIGHINTERACTSECPATH=NULL, HUMIDINTERACTPRIPATH=HQ_IPHUNRT, HUMIDINTERACTSECPATH=NULL, HULOWINTERACTPRIPATH=HQ_IPHUNRT, HULOWINTERACTSECPATH=NULL, HUBKGPRIPATH=HQ_IPHUNRT, HUBKGSECPATH=NULL; //Run ADD FACTORTABLE to add one activity factor record.

Note: 4 and 5 are mandatory. The two items are required by running the command ADD ADJMAP.

ADD FACTORTABLE:FTI=1, REMARK="IUCS", GENCCHDL=70, GENCCHUL=70, MBMSCCHDL=100, SRBDL=15, SRBUL=15, VOICEDL=70, VOICEUL=70,

CSCONVDL=100, CSCONVUL=100, CSSTRMDL=100, CSSTRMUL=100,

PSCONVDL=70, PSCONVUL=70, PSSTRMDL=100, PSSTRMUL=100, PSINTERDL=100, PSINTERUL=100, PSBKGDL=100, PSBKGUL=100, HDSRBDL=50, HDCONVDL=70, HDSTRMDL=100, HDINTERDL=100, HDBKGDL=100, HUSRBUL=50, HUCONVUL=70, HUSTRMUL=100, HUINTERUL=100, HUBKGUL=100;

//Run ADD ADJMAP to add one activity factor record to configure the corresponding transport resource mapping table for different levels of subscribers, and configure the activity factor table.

ADD ADJMAP: ANI=11, CNMNGMODE=SHARE, TMIGLD=1, TMISLV=1, TMIBRZ=1, FTI=1;

6.5.5 Adding User Plane Data of Iur Interface

//Run ADD PORTCTRLER to add transport resources for the designated port to manage and control the SPUa subsystem.

ADD PORTCTRLER: SRN=0, SN=16, PT=ETHER, CARRYEN=0, CTRLSN=4,

CTRLSSN=0, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0,

//Run ADD IPPATH to add one IP PATH. To add more IP PATHs, run the command for multiple times.

ADD IPPATH:ANI=11, PATHID=0, PATHT=HQ_QOSPATH, IPADDR="172.18.62.65", PEERIPADDR="172.18.30.65", PEERMASK="255.255.255.255", TXBW=1000000,

RXBW=1000000, CARRYFLAG=NULL, FPMUX=NO, FWDHORSVBW=0,

BWDHORSVBW=0, FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0,

BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=ENABLED,

ECHOIP="172.18.30.65", PERIOD=5, CHECKCOUNT=5, ICMPPKGLEN=64;

//Run ADD IPRT to add the IP route (it is optional and configured when L3 networking is used between the RNC and the CS).

//Route of user plane and signaling plane (Peer signaling and user plane address are normalized)

ADD IPRT: SRN=0, SN=16, DESTIP="172.18.30.65", MASK="255.255.255.255", NEXTHOP="172.18.62.70", PRIORITY=HIGH, REMARK="IUR IPRT BETWEEN RNC12 AND RNC11";

In document IPRAN Deployment Guide V210-20090303 (Page 105-109)