STM-1 only card integration with ABC - Handbook - IP-20N Basic Training Course T7.9

• ABC group should allow the following combination of types of cards 1. RMC-E/STM-1 and RMC-E

2. RMC-E/STM-1 and RMC-B 3. RMC-E and STM-1 4. RMC-B and STM-1 5. RMC-B only 6. RMC-E only

• Attaching to a group

• Can this be done dynamically (adding STM-1 card to an existing group)

• Group admin shall not be dependent on STM-1 admin

• STM-1 may be disabled but the group enabled

• Group size

• Up to four STM-1 channels shall be supported per group

• This is unrelated to the number of cards (no validation)

• Interface number is priority as well

• Group max size shall be 4 radios + 4 STM-1 cards (8 members)

Proprietary and Confidential

•

TCC-B-MC,RMC-B and 1/OC3 Interface (RMC-E should be used as STM-1/OC3 interface as well) are required – check Platform/Management/Inventory

•

Add needed cards Platform/Shelf Management/Chassis Configuration/Enable them

Multi Carrier ABC 2+0 1- Cards configuration

Proprietary and Confidential 21

Multi Carrier ABC 2+0 2 – MC ABC Configuration

1. Create ABC Group 1 consists of radio slots and STM-1 slots 2. Check if ABC group has Admin status – Enable

3. Setup MRMC, Freq., Link ID per each radio link 4. Check if ABC MUX Number 1 is enabled 5. Check IF Manager – MC ABC Grop1 is enabled 6. Enable STM-1 interfaces

7. Enable all radio slots in Chassis Configuration and STM-1 cards as well

Multi-Carrier ABC 2+2 HSB Configuration

Proprietary and Confidential

•

TCC-B-MC and RMC-B are required – check Platform/Management/Inventory

•

Add needed cards Platform/Shelf Management/Chassis Configuration/Enable them

Multi Carrier ABC 2+2 HSB 1- Cards configuration

HSB 1 HSB 2

1 2

P1 P2

Proprietary and Confidential

Multi Carrier ABC 2+2 HSB 2 - MC-ABC pre-configuration

1. Enable CMR via CLI per each slot belongs to ABC group (slot 3,4,7,8) root> platform shelf-manager abc mode admin set slot 3 state enable

2. Configure Multi Carrier ABC group. Create Group 1, use any name (2+2 HSB), press Finish – Submit (not next)

3. Edit created group and Enable protection

4. You are not able to add any members because they haven’t been created yet.

!!!

Proprietary and Confidential

•

Create Protection Group #1 (slot 3 &7) and Protection Group #2 (slot 4 & 8)

Multi Carrier ABC 2+2 HSB 3 - Protection Groups

1+1 HSB is used only for TCC-B 1+1 HSB SD is used only for TCC-B-MC

Slot 3 Slot 4

Slot 7 Slot 8

Note: If configuration will failed, please enable CMR for each radio slot in CLI:

root>platform shelf-manager abc mode admin set slot 3 state enable

Proprietary and Confidential

•

Configure 1^stlink – slot 3 (MRMC, freq., Link ID)

•

Copy to mate – slot 3 will be source radio, it means that whole configuration (MRMC, freq., link ID) will be copied to slot 7.

•

Configure 2^ndlink– slot 4 (MRMC, freq., Link ID)

•

Copy to mate – slot 4 will be source radio, it means that whole configuration (MRMC, freq., link ID) will be copied to slot 8.

2+2 HSB is now ready!!! (but we need add members for ABC)

Multi Carrier ABC 2+2 HSB 4 - Protection Groups

Slot 3 Slot 4

Slot 7 Slot 8

Proprietary and Confidential

Multi Carrier ABC 2+2 HSB

5- MC ABC Configuration – Adding members

1. Add Protection Group #1 & Protection Group #2 into ABC 2. Check if Members PG1 & PG2 are enabled

3. Check if in MUX Configuration is Enabled ABC MUX Number 1 4. Check Interface Manager if Multi Carrier ABC Group #1 is UP

5. Chassis Configuration – Change operation status per each ABC slot to Enable

Multi-Carrier ABC 2+2 HSB XPIC Configuration

Video link: https://app.box.com/s/r60ek2xse43o94phhgt6

Proprietary and Confidential

•

TCC-B-MC and RMC-B are required – check Platform/Management/Inventory

•

Add needed cards Platform/Shelf Management/Chassis Configuration/Enable them

Multi Carrier ABC 2+2 HSB XPIC 1- Cards configuration

Proprietary and Confidential

Multi Carrier ABC 2+2 HSB XPIC 2 - MC-ABC pre-configuration

1. Enable CMR via CLI per each slot belongs to ABC group (slot 3,4,7,8) root> platform shelf-manager abc mode admin set slot 3 state enable

2. Configure Multi Carrier ABC group. Create Group 1, use any name (2+2 HSB), press Finish – Submit (not next)

3. Edit created group and Enable protection

4. You are not able to add any members because they haven’t been created yet.

!!!

Proprietary and Confidential

•

Create Protection Group #1 (slot 3 &7) and Protection Group #2 (slot 4 & 8)

Multi Carrier ABC 2+2 HSB XPIC 3 - Protection Groups

1+1 HSB is used only for TCC-B 1+1 HSB SD is used only for TCC-B-MC

Slot 3 Slot 4

Slot 7 Slot 8

Note: If configuration will failed, please enable CMR for each radio slot in CLI:

root>platform shelf-manager abc mode admin set slot 3 state enable

Proprietary and Confidential

•

Configure 1^stlink – slot 3 (MRMC, freq., Link ID)

•

Copy to mate – slot 3 will be source radio, it means that whole configuration (MRMC, freq., link ID) will be copied to slot 7.

•

Configure 2^ndlink– slot 4 (MRMC, freq., Link ID)

•

Copy to mate – slot 4 will be source radio, it means that whole configuration (MRMC, freq., link ID) will be copied to slot 8.

2+2 HSB is now ready!!! (but we need add members for ABC)

Multi Carrier ABC 2+2 HSB XPIC 4 - Protection Groups

Slot 3 Slot 4

Slot 7 Slot 8

Proprietary and Confidential

•

Create XPIC Group # 1 (slot 3 + slot 4)

•

Create XPIC Group # 2 (slot 7 + slot 8)

•

Enable XPIC Group #1 & # 2

Multi Carrier ABC 2+2 HSB XPIC 5- XPIC Groups configuration

Slot 3 Slot 4

Slot 7 Slot 8

Proprietary and Confidential

Multi Carrier ABC 2+2 HSB XPIC

6 – MC ABC Group Configuration – Adding members

1. Add Protection Group #1 & Protection Group #2 into ABC 2. Check if Members PG1 & PG2 are enabled

3. Check if in MUX Configuration is Enabled ABC MUX Number 1 4. Check Interface Manager if Multi Carrier ABC Group #1 is UP

5. Chassis Configuration – Change operation status per each ABC slot to Enable

Thank You

Version 4

IP-20N Licensing

October 2014

Proprietary and Confidential

Agenda

• Licensing in General

• Demo License

• CeraOS License concept

• IP-20 Licensing Scheme

• Licensed Features

Proprietary and Confidential

Licensing

•

IP-20N offers a pay as-you-grow licensing concept in which future capacity growth and additional functionality can be enabled with Activation key.

•

For purposes of licensing, each IP-20N chassis is considered a distinct device, regardless of which cards are included in the chassis. Each device contains a single Activation key.

•

Licenses are divided into two categories:

• Per Carrier – The license is per carrier

• Per Device – The license is per device, regardless of the number of carriers supported by the device.

•

Ceragon provides a web-based License Management System (LMS). The LMS enables authorized users to generate Activation keys, which are generated per IDU serial number.

•

A 1+1 HSB configuration requires the same set of licenses for both the active and the protected interfaces.

Proprietary and Confidential

In document Handbook - IP-20N Basic Training Course T7.9 - Copia (Page 168-178)