Listing Constructional Data Report (CDR)

(1)

Report Number 131101376SHA-001 Original Issued: 17-Jan-2014 Revised: 23-Sep-2020 Standard(s) Applicant Manufacturer Address Address Country Country Contact Contact Phone Phone FAX FAX Email Email (86) 0574-62166032 Ningbo Meiyu Electrical Appliance

Co., Ltd.

Household Electric Cooking and Food Serving Appliances [UL 1026:2012 Ed.6+R:06Jun2019]

Household Cooking and Liquid-Heating Appliances (R2014) [CSA C22.2#64:2010 Ed.7+U1;U2]

Ningbo Meiyu Electrical Appliance Co., Ltd.

Haijun Chen China

[email protected]

No.1 Yaobei Road, Simen Town, Yuyao City, Zhejiang

(86) 0574-62162558 [email protected] (86) 0574-62166032

Haijun Chen

(86) 0574-62162558

China

(2)

Product Brand name Models Model Similarity Ratings Other Ratings Popcorn Maker NA NA

MY-B012 and MY-B014 share the same construction and use the same components, they are different at the apperance.

MY-B012-1 and MY-B012 have the same appearance, but they use different type of thermostat and the position of thermostat for MY-B012-1 is on the surface of heating house, the position of thermostat for MY-B012 is on the surface of mica plate which support heating wire. So as to MY-B014-1 and MY-B014.

MY-B012-1, MY-B021 and MY-B022 share the same construction and use the same components, they are different at the appearance.

MY-B024 and MY-B012-1 share the same construction and use the same components, they are different at the appearance.

120V~, 60Hz, 1200W

Description The products covered by this report are household use popcorn makers, provided with permanently attached flexible power supply cord terminated in a polarized plug.

MY-B012, MY-B014, MY-B012-1, MY-B014-1, MY-B021, MY-B022, MY-B024

(3)

Photo 1 - Overview for MY-B012 and MY-B012-1

Photo 2- Side view for MY-B012 and MY-B012-1

01 02 03 04 05 06 ED 16.3.15 (20-Apr-17) Mandatory

(4)

Photo 3 - Rear view for MY-B012 and MY-B012-1

Photo 4 - Top view for MY-B012 and MY-B012-1

07

(5)

Photo 5 - Bottom view for MY-B012 and MY-B012-1

Photo 6- Internal view for MY-B012 and MY-B012-1

08 09 10 11 12 13

27

ED 16.3.15 (20-Apr-17) Mandatory

(6)

Photo 7 - Vessel view for MY-B012 and MY-B014

Photo 8 - Motor view for all models

15 14

16

17

(7)

Photo 9 - Thermal cut out and thermal fuse view for MY-B012 and MY-B014

Photo 10 - Vessel, mica paper and blade view for all models

18 19 20 21 22 ED 16.3.15 (20-Apr-17) Mandatory

(8)

Photo 11 - Heating element view for all models

Photo 12 - PCB view for all models

23

24

25

26

(9)

Photo 13 - Overview for MY-B014 and MY-B014-1

Photo 14- Side view for MY-B014 and MY-B014-1

(10)

Photo 15 - Rear view for MY-B014 and MY-B014-1

Photo 16 - Top view for MY-B014 and MY-B014-1

(11)

Photo 17 - Bottom view for MY-B014 and MY-B014-1

Photo 18- Internal view for MY-B014

(12)

Photo 19 - Thermotat view for MY-B012-1 and MY-B014-1

Photo 20 -Thermal fuse view for MY-B012-1, MY-B014-1 and MY-B024

28

(13)

Photo 21 - Overview for MY-B021

Photo 22- Top view of MY-B021

(14)

Photo 23 - Bottom view of MY-B021

Photo 24- Internal view of MY-B021

(15)

Photo 25 - Overview for MY-B022

Photo 26 - Top view of MY-B022

(16)

Photo 27 - Bottom view of MY-B022

(17)

Photo 29 - Over view of MY-B024

(18)

o to # Item no.1 Name Manufacturer/

trademark2 Type / model

2 Technical data and securement

means conformity3

1 1 Air export KURARAY CO

LTD (E90350) G2330

PA, Rated 94V-0,

RTI(150,130,150), HWI:0, HAI:0, Min. thickness: 1.5mm. Secured into main body by screws.

cURus 1 2 Main body LG Chemical (Guangzhou) Engineering Plastics Co. Ltd. (E248280) GP-1007F PP, Rated 94V-2,

RTI(120,120,120), HWI:3, HAI:0, Min. thickness: 1.6mm. Together with base enclosure.

cURus

1 3 Power cord Various HPN

Rated 18AWG × 2C, 300V, 105°C, VW-1, 0.6 - 2.1m in length. Terminated in a mold-on

recognized polarized plug.

UL, CSA or ETL

1 4 Power plug Various Various NEMA 1-15P, Rated 125V 10A. Polarized with one wide blade.

UL, CSA or ETL 2 5 Corn scoop LG Chemical (Guangzhou) Engineering Plastics Co. Ltd. (E248280) GN-1006F PC, Rated 94V-2,

RTI(120,110,120), HWI:3, HAI:0, Min. thickness: 1.5mm. Detachable part. cURus 2 6 Cover LG Chemical (Guangzhou) Engineering Plastics Co. Ltd. (E248280) GN-1006F PC, Rated 94V-2,

RTI(120,110,120), HWI:3, HAI:0, Min. thickness: 1.5mm.

Detachable part.

cURus

3 7 Strain relief LG CHEMICAL

LTD (E67171) GP-2(j3)1BF

PA66, Rated 94V-0, HWI=0, HAI=0, RTI(120 110 110),

min.thickness: 1.8mm, Secured to metal panel by snap-in.

cURus 5 8 Foot Ningbo Meiyu Electrical Appliance Co., Ltd.

PVC Four pieces slot fitted to Base. NR

5 9 Marking label SUZHOU YONG CHENG PACKING & PRINT CO LTD (MH25146)

KL-TYL50 125ºC, attached on the bottom of

enclosure. cURus 6 10 Wire connector HEAVY POWER CO LTD (E113650) CE2 Rated 94V-2, 300V, 105℃, Min.thickness: 1,0mm. cURus 6 11 Internal wire Various 3122 Rated 300V, 200°C, 18AWG . cURus

(19)

means conformity3 ZHEJIANG HONGHUA ELECTRONICS CO LTD (E199128) KDC-A05 Rated 125V, 10A, 105°C, 6K cycles. Secured to main body by integral tabs.

cURus

Hongju (Dongguan) Electronic & Metal Products Co. Ltd. (E246644)

MR-110-C5N-BB

Rated 125V, 10A, 85°C, 10K

cycles. Others same as above. cURus

SHENZHEN BAOKEZHEN ELECTRONICS CO LTD (E176026) SC768 Rated 125V, 15A, 85°C, 6K

YUEQING WEITE ELECTRONICS CO LTD

(E334337)

KCD1 Rated 125V, 10A, 105°C, 6K

YUEQING LUSTER ELECTRONICS CO LTD (E242326) KCD5-2P-22 Rated 125V, 10A, 85°C, 6K

6 13 Cord anchorge

LG CHEMICAL

LTD (E67171) GP-2(j3)1BF

PA66, Rated 94V-0, HWI=0, HAI=0, RTI(120 110 110), min.thickness: 1.8mm, Secured on motor support by screws.

cURus

7 14 DC Motor

Ningbo Meiyu Electrical

Appliance Co. Ltd.

RS-385SA DC24V, Class 120, Secured to

Motor Support by screws. See 5.0

7 15 Sleeving SHENZHEN WAHCHANGWEI INDUSTRIAL CO LTD (E233803) SRS-70

Grade A silicone-polymer coated fiberglass sleeving, 600V, 200°C. Used to cover internal wire.

cURus

7 16 Motor support KURARAY CO

LTD (E90350) G2330

PA, Rated 94V-0,

RTI(150,130,150), HWI:0, HAI:0, Min. thickness: 1.5mm. Secured into main body by screws.

cURus 7 17 Vessel Ningbo Meiyu Electrical Appliance Co., Ltd. Aluminium 0.6mm thick. NR Zhejiang Rongtai Electric Material Co., Ltd. (E231452) R-5660 Min. Thickness: 0.6mm.

Supporting Heating Element. cURus JIAXING

HONGTONGYAY E INSULATING MATERIALS CO LTD (E256107)

HT556X-X Min. Thickness: 0.6mm cURus

9 18 Support Mica Power switch 12

6

(20)

means conformity3

9 19 Thermal fuse Aupo Electronics

Ltd. (E140847) BF192

Rated 15A, 125V, Tf: 192°C.

Secured to Mica Plate by eyelets. cURus FOSHAN GAOMING XI TE ELECTRICAL CO LTD (E225655) AMT 125V, 16A, 10000 cycles, Operating temperature: 100°C, Secured on mica support by rivet. For MY-B012 and MY-B014

cURus FOSHAN CHAN CHENG EAGLE TECHNOLOGY CO LTD (E301742) AMT-C1* 125V, 16A, 10000 cycles, Operating temperature: 100°C. For MY-B012 and MY-B014

cURus Zhejiang Rongtai Electric Material Co., Ltd. (E231452) R-5660 Min. Thickness: 0.15mm.

Wrapped around inside surface of Vessel Support. cURus JIAXING HONGTONGYAY E INSULATING MATERIALS CO LTD (E256107)

10 22 Blade LG Chemical (Guangzhou) Engineering Plastics Co. Ltd. (E248280) GN-1006F PC, Rated 94V-2,

RTI(120,110,120), HWI:3, HAI:0, Min. thickness: 1.5mm. Tight fitted to the shaft of DC Motor.

cURus 11 23 Heating element 1 Ningbo Meiyu Electrical Appliance Co. Ltd.

NBMY-001 Secured to Mica Plate by eyelets

and fixed by Support Mica See 5.0

11 24 Heating element 2

Appliance Co. Ltd.

NBMY-002 Secured to Mica Plate by eyelets

and fixed by Support Mica See 5.0 Zhejiang Rongtai

Electric Material Co., Ltd. (E231452)

R-5660 Min. Thickness: 0.6mm.

Supporting Heating Element. cURus JIAXING

HONGTONGYAY E INSULATING MATERIALS CO LTD (E256107)

12 26 PCB LEUCHTEK ELECTRONICS (ZHEJIANG) CO LTD (E199273) PFR-1 Rated 94V-0, 130°C. Min. Thickness: 0.8mm. Soldered on DC Motor. cURus 11 25 Support Mica Mica paper 21 10 Thermostat 1 20 9 ED 16.3.15 (20-Apr-17) Mandatory

(21)

means conformity3 6 27 Quick connector ZHEJIANG YUESHEN ELECTRON CO LTD (E315941) TJC3-XXY Series

Used for internal wire to power

switch. Min. thickness 0.4mm. cURus

FOSHAN

GAOMING XI TE ELECTRICAL CO LTD (E225655)

KSD302

Rated 125V, 16A, Set-point temperature: 180°C. Secured on heating house by metal plate. For B012-1, B014-1, MY-B021, MY-B022 and MY-B024.

cURus GUANGDONG SHUNDE ZHONGBAO THERMOSTAT TECHNOLOGY CO LTD (E213536) KSD301-C

cURus TONGBAO-HUALONG CONTROLS CO LTD (E137238) KSD301

cURus Thermostat 2

28 19

NOTES:

1) Not all item numbers are indicated (called out) in the photos, as their location is obvious.

2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s) of conformity" can be used.

3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted and only visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section 5.0 for details.

(22)

Photo # Item no. 7 14 A NA NA NA Frequency: Annual 1 INSULATED COIL

Name Manufacturer/Trademark Type / model

DC Motor Ningbo Meiyu Electrical

Appliance Co. Ltd. RS-385SA

Electrical Rating: 24Vdc Insulation class

Component Standard used: Test with appliance MATERIALS LIST

Component Manufacturer Type/model Dimensions/thickness/assembly information

Windings HUAERDA

GROUP CO LTD UEW

MW82, polyurethane film coated magnet wire, 180℃_{. (E227046)}

Core Various Steel sheet Steel

WINDING(S) RESISTANCE Winding

Designation

Wire Size

(AWG or mm2) Wire Type Turns Volts Amps

DC resistance (Ω) +/- 10%:

NA NA NA NA

1240

Test Site: CEC Number of samples to test: VERIFICATION PROCESS

Dielectric Strength

60s

Test Name Test Parameters

Visual and verify the no load speed and no load current

No load speed: 17000rpm No load current: 0.21A

Overall assembled dimension as below

Apply voltage Between Test Voltage Test Time Winding to core

Plastic cover LG CHEMICAL

LTD GP-2(j2)1AF PA6, V-0, RTI (120 110 115), (E67171)

(23)

Photo # Item no. 11 23 NA 120 200 Frequency: Annual 1 HEATER ELEMENT Type / model Heating element 1 Ningbo Meiyu Electrical

Appliance Co. Ltd. NBMY-001

Electrical Rating: 120V Insulation class

Name Manufacturer/Trademark

Fiber glass Used to support heating wire Component Standard used: UL 1026 & CSA C22.2 No.64

MATERIALS LIST

Component Manufacturer Type/model Dimensions/thickness/assembly information Heating wire Ningbo Meiyu

Electrical OCr25AL5 Ø0.68mm, O.D. 6.5mm, 200W

Fieber glass suport

Appliance Co. Ltd.

ELEMENT RESISTANCE Element

Designation Overall assembled dimensions Volts Watts

OCr25AL5 Ø0.68mm, O.D. 6.5mm 9.5Ω

VERIFICATION PROCESS

Test Site: CEC Number of samples to test:

Winding resistance See resistance per element above.

Dielectric Strength

Apply voltage Between Test Voltage Test Time

Live parts and sheath NA NA

Live parts and housing NA NA

(24)

Photo # Item no. 11 24 NA 120 1000 Frequency: Annual 1 HEATER ELEMENT

Name Manufacturer/Trademark Type / model

Heating element 2 Ningbo Meiyu Electrical

Appliance Co. Ltd. NBMY-002

Electrical Rating: 120V Insulation class

Fiber glass Used to support heating wire Component Standard used: UL 1026 & CSA C22.2 No.64

MATERIALS LIST (refer to illustration _ for assembly drawing)

Component Manufacturer Type/model Dimensions/thickness/assembly information

Heating wire

Appliance Co. Ltd.

OCr25AL5 Ø0.68mm, O.D. 4.3mm, 1000W

Fieber glass suport

Appliance Co. Ltd.

ELEMENT RESISTANCE Element

Designation Overall assembled dimensions Volts Watts

OCr25AL5 Ø0.68mm, O.D. 4.3mm 2.2Ω

CEC Number of samples to test:

VERIFICATION PROCESS

Test Site:

Winding resistance See resistance per element above.

Dielectric Strength

Apply voltage Between Test Voltage Test Time

Live parts and sheath NA NA

Live parts and housing NA NA

(25)

2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and display lamps are mounted and prevented from shifting or rotating by the use of lockwashers,

starwashers, or other mounting format that prevents turning of the component.

3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or the equivalent.

4. Accessibility of Live Parts - All uninsulated live parts in primary circuitry are housed within a plastic enclosure constructed with no openings other than those specifically described in Sections 4 and 5. 5. Grounding - NA.

6. Polarized Connection - This product is provided with a polarized power supply connection. All single pole switches and thermal cut-out are connected only to the ungrounded supply circuit conductor. 7. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads

terminating in soldered connections are made mechanically secure prior to soldering. Recognized Component separable (quick disconnect) connectors of the positive detent type, closed loop

connectors, or other types specifically described in the text of this report are also acceptable as internal wiring terminals. At points where internal wiring passes through metal walls or partitions, the wiring insulation is protected against abrasion or damage by plastic bushings or grommets. All wiring is minimum 18 AWG, with a minimum rating of 300V, 200°C.

8. Schematics - None

9. Markings - The product is marked on as labeling system as described in item no. 9 of Section 4.0 as follows: applicant's name, model number, date of manufacturer, electrical ratings, warning sentences etc. Refer to Illustration No. 1 and 1a for details.

10. Cautionary Markings - Refer to Illustration No. 1, 1a for details.

11. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are provided by the manufacturer. Refer to Illustration No(s). 2, 2a, 2b for details.

1. Spacing - In primary circuits, _3.1_ mm minimum spacing are maintained through air and over surfaces of

insulating material between current-carrying parts of opposite polarity and _3.1__ mm minimum between

Listed Component - A component part, which has been previously Listed or Certified by an accredited Certification Organization with no restrictions and is used in the intended application within its ratings.

Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of a product that has a direct bearing on the product’s conformance to applicable requirements of the product standard.

Construction Details - For specific construction details, reference should be made to the photographs and descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the specific construction details described in this Report, the following general requirements also apply. body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified by the Conditions of Acceptability.

Unlisted Component - A part that has not been previously evaluated to the appropriate designated component standard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing or component recognition.

(26)

Illustration 1 - Marking label (representative)

Note:

1. The warning sentences are not less than 2.4mm; others are not less than 1.6mm. 2. The control number and wording

"CONFORMS TO UL STD.1026” shall be at least 1.5 mm high.

3. Carton markings “Household Use Only” is marked and the minimum height of lettering is 6.4mm.

4. Note: yy for year, mm for month.

5. ETL Logo should be clearly legible and durable.

(27)

Illustration 1a - Marking label Marking for MULTIPLE LISTEE 1:

Remark: Note: WW for week, YY for year.

The models of this marking are BC-2979 may be followed by 1 to 3 characters: where characters can be optional, or one or a combination of 2-3 letters "A" to "Z" for color identification only, one sample of them see below:

(28)

Illustration 2 - Instruction Manual

Popcorn maker MY-B012, MY-B014, MY-B012-1, MY-B014-1, MY-B021, MY-B022, MY-B024

The height of lettering in the text and illustrations of the safety instructions shall be as follows: a) Upper case letters shall not be less than 1/12 inch (2.11 mm) in height;

b) Lower case letters shall not be less than 1/16 inch (1.6 mm) in height; and

c) The phrases "IMPORTANT SAFEGUARDS" and "SAVE THESE INSTRUCTIONS" shall be in letters no less than 3/16 inch (4.8 mm) in height.

(29)

Illustration 2a - Instruction Manual

(30)

Illustration 2b - Instruction Manual

(31)

Illustration 3 - Drawing for DC motor

(32)

Illustration 4 - Drawing for heating element Heating element 1:

Heating element 2:

(33)

Sample Rec. Date 26-Nov-13 Condition Prototype Sample ID. 0131126-03-001 Test Location Test Procedure UL 1026, 6th Edition, Dated January 27, 2012 Clause UL 746C, 6th Edition, Rev. February 06, 2013 Clause ---8 --- ---10.2.2 --- ---37 --- ---38 --- ---39 --- ---41 --- ---43 --- ---44 --- ---46 --- ---47 --- ---52 --- ---53 --- ---55 --- ---60 --- --- 31 --- 56 --- 61

---Component Switches and Control Devices

Strain Relief Test After Mold Stress-Relief Distortion Resistance to Impact Test

Mold Stress-relief Distortion Test Abnormal Operation Tests

Tests for Insulation Resistance and Leakage Current as a Result of Moisture

Intertek Testing Services Shanghai Limited Testing Lab

Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria.

Leakage Current Test

The following tests were performed:

Stability Strain relief

Metal Enclosure Impact Tests Test Description

Normal Temperature Test

Dielectric Voltage-Withstand Test Power Input Test

Push-Back Relief Test Operational Tests

Non-Metallic Enclosure-Fasteners Test Broken Element Test

(34)

Evaluation Period Project No. 150702782SHA Sample Rec. Date 31-Jul-15 Condition Prototype Sample ID. 0150731-03-001 Test Location Test Procedure UL 1026, 6th Edition, Dated August 10, 2015 Clause UL 746C, 6th Edition, Rev. June 23, 2015 Clause ---8 --- ---10.2.2 --- ---37 --- ---38 --- ---39 --- ---41 --- ---43 --- ---44 --- ---46 --- ---47 --- ---52 --- ---53 --- ---55 --- ---60 --- --- 31 --- 56 --- 61 ---31-Jul-15 to 16-Oct-15

The following tests were performed:

Test Description Stability

Strain relief

Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria.

Abnormal Operation Tests

Component Switches and Control Devices

Strain Relief Test After Mold Stress-Relief Distortion Resistance to Impact Test

Power Input Test Leakage Current Test Operational Tests

Tests for Insulation Resistance and Leakage Current Dielectric Voltage-Withstand Test

Broken Element Test Push-Back Relief Test

Mold Stress-relief Distortion Test Metal Enclosure Impact Tests

Non-Metallic Enclosure-Fasteners Test

(35)

Sample Rec. Date 11-May-2016 Condition Prototype Sample ID. 0160511-04-001-004 Test Location Test Procedure UL 1026 Issued: 2012/01/27 Ed: 6 Rev: 2015/08/10 Clause CSA C22.2#64 Issued: 2010/03/01 (R2014) Ed: 7, Gen. Inst. 1: ---8 7.15 --10.2.2 5.6.4 --37 7.2 --38 7.8 --39 -- --41 7.3 --43 -- --44 7.5 --46 7.25 --47 -- --53 -- --55 7.4 --60 7.9 ---- 7.6

--Evaluation Period Project No. 170501187SHA

Sample Rec. Date NA Condition Prototype Sample ID. NA

Test Location Test Procedure UL 1026:2012 Ed.6+R:10Apr20 17 Clause CSA C22.2#64:2010 Ed.7+U2 Clause

---Push-Back Relief Test

Non-Metallic Enclosure-Fasteners Test Abnormal Operation Test

Flexing (Power Supply Cords and Cord Sets) and Detachment

Dielectric Voltage-Withstand Test Broken Element Test

Leakage Current Test Operaton Tests

Normal Temperature Test Stability

Strain Relief Test Power Input Test

Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria. The following tests were performed:

Test Description

12-May-2017 to 25-May-2017

Only the standard version updated, none tests need to do:

Test Description

(36)

Sample Rec. Date 2-Aug-2018 Condition Prototype Sample ID. 0180802-04-001-002 Test Location Test Procedure 1026:2012 Ed.6+R:02Feb20 18 Clause CSA C22.2#64:2010 Ed.7+U2 Clause ---8 7.15 --10.2.2 5.6.4 --37 7.2 --38 7.8 --39 -- --41 7.3 --43 -- --44 7.5 --46 7.25 --47 -- --53 -- --55 7.4 --60 7.9 ---- 7.6

--Intertek Testing Services Shanghai Limited Testing Lab

Test Description Stability

Strain Relief Test Power Input Test Leakage Current Test Operaton Tests

Push-Back Relief Test

(37)

Sample Rec. Date 22-Jul-2020 Condition Prototype Sample ID. 0200722-04-001-002 Test Location Test Procedure UL 1026:2012 Ed.6+R:06Jun20 19 Clause CSA C22.2#64:2010 Ed.7+U1;U2 Clause ---8 7.15 --10.2.2 5.6.4 --37 7.2 --38 7.8 --39 -- --41 7.3 --43 -- --44 7.5 --46 7.25 --47 -- --53 -- --55 7.4 --60 7.9 ---- 7.6

--Completed by: Reviewed by:

Title: Title:

Push-Back Relief Test

Leakage Current Test Operaton Tests

Normal Temperature Test Stability

Strain Relief Test Power Input Test

Test Description

Signature: Signature:

A representative sample of the product covered by this report has been evaluated and found to comply with the applicable requirements of the standards indicated in Section 1.0.

Gavin Fu Wayle Chen

Engineer Reviewer

8.1 Signatures

(38)

BASIC LISTEE Address Country Product MULTIPLE LISTEE 1 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country

BASIC LISTEE MODELS MY-B012-1 MULTIPLE LISTEE 2 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country

BASIC LISTEE MODELS

MULTIPLE LISTEE 3 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country

BASIC LISTEE MODELS Popcorn Maker

China

The following products, which are identical to those identified in this report except for model number and Listee name, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program.

Ningbo Meiyu Electrical Appliance Co., Ltd.

MULTIPLE LISTEE 2 MODELS

MULTIPLE LISTEE 3 MODELS None

Ningbo Meiyu Electrical Appliance Co., Ltd.

No.1 Yaobei Road, Simen Town, Yuyao City, Zhejiang China

MULTIPLE LISTEE 1 MODELS BC-2979 may be followed by 1 to 3 characters

None

BETTY CROCKER Formula Brands Inc.

45 Mural Street, Unit 7, Richmond Hill, Ontario, L4B 1J4 Canada

(39)

with the requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorization prior to using alternate parts, components or materials.

COMPONENTS

Components used shall be those itemized in this Intertek report covering the product, including any amendments and/or revisions.

LISTING MARK

The ETL Listing mark applied to the products shall either be separable in form, such as labels purchased from Intertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is subject to the control of Intertek.

The mark must include the following four items:

1) applicable country identifiers "US" and/or "C" or "US", "C" and "EU"

2) the word "Listed" or "Classified" or "Recognized Component" (whichever is appropriate) 3) a control number issued by Intertek

4) a product descriptor that identifies the standards used for certification. Example:

For US standards, the words, “Conforms to” shall appear with the standard number along with the word, “Standard” or “Std.” Example: “Conforms to ANSI/UL Std. XX.”

For Canadian standards, the words “Certified to CAN/CSA Standard CXX No. XX.” shall be used, or abbreviated, “Cert. to CAN/CSA Std. CXX No. XX.”

Can be used together when both standards are used.

Note: A facsimile must be submitted to Intertek, Attn: Follow-up Services for approval prior to use. The facsimile need not have a control number. A control number will be issued after signed Certification Agreements have been received by the Follow-up Services office, approval of the facsimile of your proposed Listing Mark, satisfactory completion of the Listing Report, and scheduling of a factory assessment in your facility.

MANUFACTURING AND PRODUCTION TESTS

Manufacturing and Production Tests shall be performed as required in this Report. FOLLOW‑UP SERVICE

Periodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shall be scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to the following:

1. Conformance of the manufactured product to the descriptions in this Report.

2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification 3. Manufacturing changes.

4. Performance of specified Manufacturing and Production Tests.

In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, the Applicant shall take one or more of the following actions:

1. Correct the non-conformance.

2. Remove the ETL Mark from non-conforming product.

3. Contact the issuing product safety evaluation center for instructions.

(40)

Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writing when these components must be selected and sent to the CEC for re-evaluation

Ship the samples to:

Intertek Testing Services Shanghai Limited ETL Component Evaluation Center

Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China

Attn: Ms. Angela Han

Sample Disposition: Due to the destructive nature of the testing, all samples will be discarded at the conclusion of testing unless, the manufacturer specifically requests the return of the samples. The request for return must accompany the initial component shipment.

Intertek may require these components to be tested and/or evaluated at least once annually, more often for certain components, as part of the independent certification process. The Unlisted Components in Section 5.0 require testing and/or evaluation as indicated.

(41)

Product Test Voltage Test Time

All products covered by this Report. 1000V 60 s

or

1200V 1 s

11.1 Dielectric Voltage Withstand Test Required Tests

Dielectric Voltage Withstand Test Polarization Test

The test equipment shall incorporate a transformer with an essentially sinusoidal output, a means to indicate the applied test potential, and an audible and/or visual indicator of dielectric breakdown.

Test Equipment Method

The test voltage specified below shall be applied between primary circuits and accessible dead-metal parts. The test voltage may be gradually increased to the specified value but must be maintained at the specified value for one second or one minute as required.

One hundred percent of production of the products covered by this Report shall be subjected to a routine production line dielectric withstand test.

The test shall be conducted on products, which are fully assembled. Prior to applying the test potential, all switches, contactors, relays, etc., should be closed so that all primary circuits are energized by the test potential. If all primary circuits cannot be tested at one time, then separate applications of the test potential shall be made.

The test equipment shall incorporate a voltmeter in the output circuit to indicate directly the applied test potential if the rated output of the test equipment is less than 500VA.

If the rated output of the test equipment is 500VA or more, the applied test potential may be indicated by either:

1 - a voltmeter in the primary circuit;

2 - a selector switch marked to indicate the test potential; or

3 - a marking in a readily visible location to indicate the test potential for test equipment having a single test potential output.

In cases 2 and 3, the test equipment shall include a lamp or other visual means to indicate that the test potential is present at the test equipment output. All test equipment shall be maintained in current calibration.

Products Requiring Dielectric Voltage Withstand Test:

Products Requiring Polarization Test: All products covered by this Report. 11.2 Polarization Test:

Method

Each appliance provided with a polarized attachment plug (2-wire plug with one blade wider than another) shall be tested with a polarized continuity between the grounded supply-circuit conductor of the attachment plug (wide blade of a 2-wire plug) and the part of the appliance that is intended to be connected to the grounded supply-circuit conductor. If the continuity cannot be readily determined by visual inspection and component checking, an electrical continuity test is to be made.

(42)

Date/ Project Handler/ Proj # Site ID Reviewer

19-Oct-2015 Gavin Fu/

Wayle Chen 1

-Update the standard to UL Standard for Safety for Electric Household Cooking and Food Serving Appliances, UL 1026, 6th Edition, Dated August 10, 2015.

150702782S

HA 1

-Change the adress to "No.1 Yaobei Road, Simen Town, Yuyao City, Zhejiang, China"

2 - Add a new model MY-B014.

3 13-18 Add the photo for new model MY-B014

7 1,2 Add the marking of MY-B014 and add the information of MY-B014 into the manual.

8 - Add the test information about the change. 20-Jan-2016 Gavin Fu/

Wayle Chen 4 12 Add a alternative power switch (type SC768, E176026). 160101415S

HA

25-May-2016 Gavin Fu/

Wayle Chen 1

-Add standard Household Cooking and Liquid-Heating Appliances - CSA C22.2#64 Issued: 2010/03/01 (R2014) Ed: 7, Gen. Inst. 1: 2013.

160501052S

HA 2

-Add two new models MY-B012-1 and MY-B014-1, also add the model similarity information.

3

1, 2, 3, 4, 5, 6

Add the new added model MY-B012-1 in photo name.

3

13,14, 15,16, 17

Add the new added model MY-B014-1 in photo name.

3 19, 20 Add two photo for internal view for new added models MY-B012-1 and MY-B014-1

4 20 Change the component name from "Thermostat" to "Thermostat for MY-B012 and MY-B014"

4 28 Add the thermostat for MY-B012-1 and MY-B014-1 in the list.

7 1 Remove the original marking, add the new marking for added standard and models.

7 2 Add the information of new added models and French warning in the manual.

8 - Add the test information about the new standard and new added models.

8-Jul-2016 Gavin Fu/

Wayle Chen 7 1

Add the Marking for MULTIPLE LISTTE 1 about models BC-2979XXX, where "XXX" can be optional, or one or a combination of 2-3

letters "A" to "Z" for color identification only. 160700642S

HA 9 1

Add MULTIPLE LISTEE 1 for model BC-2979XXX with brand name "BETTY CROKER” which according to basic models MY-B012-1 for Formula Brands Inc.

2-Jun-2017 Gavin Fu/

Wayle Chen 1

-Update the standard from UL 1026 Issued: 2012/01/27 Ed: 6 Rev: 2015/08/10 to UL 1026:2012 Ed.6+R:10Apr2017, from CSA C22.2#64 Issued: 2010/03/01 (R2014) Ed: 7, Gen. Inst. 1: 2013 to CSA C22.2#64:2010 Ed.7+U2. 170501187S

HA 8 - Add the test information about the change.

Section Item Description of Change

(43)

Date/ Project Handler/ Proj # Site ID Reviewer

Section Item Description of Change

22-Oct-2018 Gavin Fu/

Wayle Chen 1

-Updated standard from "Standard For Household Electric Cooking And Food Serving Appliances [UL 1026:2012 Ed.6+R:10Apr2017]" to "Household Electric Cooking And Food Serving Appliances [UL 1026:2012

Ed.6+R:02Feb2018]" 180800191S

HA 2

-Add two new models MY-B021 and MY-B022, also add the model similarity information.

3 21 to

28 Add photos 21 to 28 for new added models.

4 28 Add the information of new added models into "Technical data and securement means".

7 3, 4 Add drawing for DC motor and heating elements. 8 - Add the test information about the change.

23-Sep-2020 Gavin Fu/

Wayle Chen 1

-Standard updated from "Household Electric Cooking And Food Serving Appliances [UL 1026:2012

Ed.6+R:02Feb2018]" to "Household Electric Cooking and Food Serving Appliances [UL 1026:2012

Ed.6+R:06Jun2019]" and from "Household Cooking And Liquid-Heating Appliances [CSA C22.2#64:2010 Ed.7+U2]" to "Household Cooking and Liquid-Heating Appliances (R2014) [CSA C22.2#64:2010 Ed.7+U1;U2]"

200702528S

HA 2 - Add a new model MY-B024.

3 20 Add the new model MY-B024 in photo name. 3 29, 30 Add two photo for new added model MY-B024.

4 28 Add the information of new added model into "Technical data and securement means".

7 2 Add the information of new added model in the manual. 8.0,

8.1 - New test block added, Re-signed.