I
n this lab
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605
©
2005, Vonexus, Inc.
265
L A B
13
Gateway Backup and Restore
❒ You will back up and restore your gateway’s ini file
Objectives
At the end of this lab you will be able to:
➢
Back up the gateway’s ini file
➢
Restore the gateway’s ini file
Additional Information
Advanced Configuration - Extract Configuration File Lab 13 — Gateway Backup and Restore
Advanced
Configuration
-Extract
Configuration
File
After all configurations have been made and all testing is complete, go back into the
AudioCodes Configuration web interface to extract the INI file for safekeeping and
potential re-use on other gateways.
Step
Action
Results
1. Using the web browser, open the configuration for the gateway.
2. Log in as prompte.d
Advanced Configuration - Extract Configuration File Lab 13 — Gateway Backup and Restore
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605
©
2005, Vonexus, Inc.
267
4. In the Get INI file from the device to
your computer section, click Get ini File.
Advanced Configuration - Extract Configuration File Lab 13 — Gateway Backup and Restore
By the way
The customer and the reseller should both keep a copy of this file.
5. Click Save. The Save As dialog box appears.
When the download is finished, the Download Complete dialog box appears.
6. Type a descriptive name (for example,
192100100242Mk1000_gw_ISDN_
NI1.ini)
for the file and select secure location.Click Save.
You are returned to the Configuration File screen.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605 © 2005, Vonexus, Inc.
269
Restore a
Configuration
from an INI File
The following procedures allow you to configure a brand new gateway using the
settings from the old gateway’s ini file.
A bit of advice
These steps help ensure consistency and accuracy in the event you need to restore a
gateway (if the gateway is lost, damaged, or destroyed) or if you ever need to install
new gateways.
Step
Action
Results
1. Follow the original BootP procedures to assign an IP address, load the firmware files to the new gateway and reset the new gateway.
(Use the same files coefficient files you did for your original gateway).
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
3. Log in as prompte.d
4. Click Advanced Configuration, and select Configuration File from the menu.
5. In the Send the ini file from the device
to your computer area, click Browse.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605
©
2005, Vonexus, Inc.
271
6. Select the correct INI file and click
Open.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
7. Click OK to upload the ini file. The upload begins. A status bar below the Configuration File appears letting you know that the upload is in progress. NOTE The status bar does not provide
the results or the time remaining for the download. NOTE Also note, that when the
download is complete, the screen may flash and potentially display a Page Cannot Be Found message. If this occurs, refresh your browser screen.
8. Click Save Configuration from the menu at left.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605
©
2005, Vonexus, Inc.
273
9. Click the Save Configuration button. The configuration saves.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
11. Click the Reset button and select the option to Burn.
The system begins its reset and displays a message indicating that it will take up to3 minutes to reset.
Restore a Configuration from an INI File Lab 13 — Gateway Backup and Restore
Enterprise Interaction Center Installation and Support Lab Manual 2.3 100605
©
2005, Vonexus, Inc.
