Internet Telephony PBX System

(1)

T1/E1 Gateway

With IP PBX Application

Internet Telephony PBX

System

(2)

Case 35: With IP PBX Application

Head Office E1 PABX interconnect with VIP-2100 to establish VoIP capability, The subscribers in Head Office could communicate with Analog Phone that

belong VIP-1680FS in Branch1 and Branch2 by VoIP application.

(3)

Select the [

Select the [ Network Setup Network Setup --> WAN & LAN Setup > WAN & LAN Setup ]] of IP PBX of IP PBX to set up the WAN interfaceto set up the WAN interface

2 2

Setup the WAN interface of

Setup the WAN interface of IP PBX IP PBX followfollow the information of IP that provides by ISP the information of IP that provides by ISP WAN Port IP :

WAN Port IP : Static IPStatic IP IP Address :

IP Address : 10.150.0.2010.150.0.20 Subnet Mask :

Subnet Mask : 255.0.0.0255.0.0.0 Default Gateway :

Default Gateway : 10.150.0.25410.150.0.254

1 1

IP PBX Configuration: WAN port

(4)

3 3

4 4

Select the [

Select the [IP PBX Setup IP PBX Setup -> SIP Extension-> SIP Extension]] to set up the SIP Extensions

to set up the SIP Extensions

Add extension numbers for Add extension numbers for IPX--1900 and IP Phone1900 and IP Phone

IP PBX Configuration: SIP Extension

(5)

5

Add an Gateway Trunk for VIP

Add an Gateway Trunk for VIP--21002100 IP:IP: 10.150.0.10

Port :

Port : 5060

6

Select the [

Select the [Trunk ManagementTrunk Management -> Gateway -> Gateway Trunk

Trunk] to set up the Gateway Trunk] to set up the Gateway Trunk

IP PBX Configuration: Gateway Trunk

(6)

7 7

8 8

Select the [

Select the [Trunk ManagementTrunk Management -> Trunk-> Trunk Group

Group] to set up the Trunk Group] to set up the Trunk Group

Add an Trunk Group for E1 trunk Add an Trunk Group for E1 trunk prefix number

prefix number Group Name:

Group Name: VIP-2100 Number:

Number: 0 Trunk Group:

Trunk Group: 10.150.0.10:5060

IP PBX Configuration: Trunk Group

(7)

9 9

10 10

Attendant Number Attendant Number 555555

Select the [

Select the [Attendant Management Attendant Management ->->

Attendant Number

Attendant Number] to set up the ] to set up the Attendant number

Attendant number

IP PBX Configuration: Attendant Number

(8)

11

Select the [Save & LogoutSelect the [Save & Logout] to save ] to save configuration and reboot IP PBX.

configuration and reboot IP PBX.

12 IP PBX Configuration: Save & Reboot

IP PBX Configuration: Save & Reboot

(9)

Select the [

Select the [ Control Control --> Network > Network ] of] of E1E1 Gateway

Gateway

13 13

14 14

E1 Gateway Configuration: Signal port

Setup the

Setup the Signal portSignal port interface interface follow the follow the information of IP that provides by ISP information of IP that provides by ISP IP Address :

IP Address : 10.150.0.1010.150.0.10 IPIP NetmaskNetmask: 255.0.0.0: 255.0.0.0 IP Gateway :

IP Gateway : 10.150.0.25410.150.0.254

(10)

Select the [

Select the [ ConfigurationConfiguration -> Interface -> Interface ]] of E1 GatewayofE1 Gateway

Then press [

Then press [ ModifyModify ] button] button

E1 Gateway Configuration: Voice port

Select Interface Select Interface

15 15

16 16

17 17

(11)

Setup the

Setup the Voice portVoice port interfaceinterface follow the information of IP that follow the information of IP that provides by ISP

provides by ISP Interface Type :

Interface Type : 1 E1/T1 1 E1/T1 (According practical E1/T1 port number)(According practical E1/T1 port number) Description :

Description : VoIP 1E1/T1 Interface VoIP 1E1/T1 Interface (For references)(For references) IP Address :

IP Address : 10.150.0.1110.150.0.11 Subnet Mask :

Subnet Mask : 255.0.0.0255.0.0.0 Default Gateway :

Default Gateway : 10.150.0.25410.150.0.254 PCM Type :

PCM Type : AA--lawlaw (Depend on practical E1/T1 line)(Depend on practical E1/T1 line)

18 18

E1 Gateway Configuration: Voice port

(12)

E1 Gateway Configuration: Trunk

19 19

Press [ Modify^{Press [}Modify ] button] button

20 20

(13)

Setup Trunk interface

Setup Trunk interface follow the follow the information that provides by ISP.

information that provides by ISP.

21 21

E1 Gateway Configuration: Trunk

(14)

Select the [

Select the [ConfigurationConfiguration -> SIP-> SIP] of E1 Gateway ] of E1 Gateway to setup SIP setting for registering to IP PBX.

to setup SIP setting for registering to IP PBX.

22 22

Press [

Press [ ModifyModify ] button ] button to setup the related to setup the related SIP configuration SIP configuration

E1 Gateway Configuration: SIP Settings

After setup completed, After setup completed, press [

press [ ApplyApply ] button ] button save settings

save settings

24 24

25 25

26

(15)

Press [

Press [ ID 0ID 0 ] field] field

Then press [

Then press [ ModifyModify ]] to setup registration to setup registration configuration

configuration

E1 Gateway Configuration: SIP Settings

27 27

28 28

(16)

29 29

30 30

Press [

Press [ ActiveActive ]] mode and setup mode and setup the related SIP the related SIP configuration configuration

E1 Gateway Configuration: SIP Settings

(17)

31 31

To check E1 Gateway To check E1 Gateway if registered to IP PBX if registered to IP PBX successfully

successfully

E1 Gateway Configuration: SIP Settings

(18)

Select the [

Select the [ConfigurationConfiguration -> Digit Manipulation-> Digit Manipulation]] of E1 Gateway to add the

of E1 Gateway to add the DialplanDialplan Number.Number.

32 32

33 33

E1 Gateway Configuration: VoIP Hunting

(19)

Press [

Press [ DetailDetail ] to setup Group ID 0-] to setup Group ID 0-PSTN_IncomingPSTN_Incoming

Setup Incoming Dial Plan, and assign if called number matched th Setup Incoming Dial Plan, and assign if called number matched thee prefix number, the incoming calls will redirect to specific numb

prefix number, the incoming calls will redirect to specific numbers. ers.

56233200

56233200 : The incoming call will redirect to ext.1001 : The incoming call will redirect to ext.1001 56233201

56233201 : The incoming call will redirect to ext.2001: The incoming call will redirect to ext.2001 56233202

56233202 : The incoming call will redirect to ext.2002: The incoming call will redirect to ext.2002 56233203~9

56233203~9 : The incoming calls will redirect to AA (Auto Attendant): The incoming calls will redirect to AA (Auto Attendant)

34 34

E1 Gateway Configuration: Dial Plan

(20)

35 35

E1 Gateway Configuration: Dial Plan

35

Press [

Press [ DetailDetail ] to setup Group ID 1] to setup Group ID 1-PSTN_Mobile-PSTN_Mobile

Setup Outgoing Dial Plan, and assign if the SIP subscribers Setup Outgoing Dial Plan, and assign if the SIP subscribers dial the speed number, the calling number will become dial the speed number, the calling number will become complete numbers and call to mobile.

complete numbers and call to mobile.

60106010 : If dial 6010, it will call to 015000123 : If dial 6010, it will call to 015000123

(21)

Select the [

Select the [ControlControl -> Call Flow Editor-> Call Flow Editor] of E1 Gateway ] of E1 Gateway to setup the call flows.

to setup the call flows.

Refer to the below call flows to setup.

36 36

37 37

E1 Gateway Configuration: Call Flow

(22)

Refer to each components configuration to setup the call flows

E1 Gateway Configuration: Call Flow

<Tips>

ANI: Calling numberANI

(23)

Refer to each components configuration to setup the call flows

E1 Gateway Configuration: Call Flow

(24)

Select the [

Select the [ConfigurationConfiguration -> Apply Change-> Apply Change]] to effect the new settings.

to effect the new settings.

Select the [

Select the [ControlControl --> System> System]] Select the [

Select the [RestartRestart] to reboot ] to reboot E1 Gateway.

E1 Gateway.

38 38

39 39

40 40

E1 Gateway Configuration: Apply & Restart

(25)

A. T1/E1 Incoming calls

Depend on outside PSTN callers call the below numbers of E1/T1 Gateway, the call will transfer to AA or different SIP subscribers directly

1. 56233200: This call will transfer to ext.1001 directly 2. 56233201: This call will transfer to ext.2001 directly 3. 56233202: This call will transfer to ext.2002 directly

4. 56233203~56233209: These calls will transfer to IVR of IP PBX, the caller will hear prompts for transfer to desired extension after input extension number

B. T1/E1 Outgoing calls

The SIP subscribers dial the E1/T1 trunk prefix number 0 at first, and hearing a dial- tone, then depend on the SIP subscribers if calling the speed dial number

1. 6010: This call will call to 015000123 2. 6019: This call will call to 015000456 3. 6020: This call will call to 015000789 4. 567110: This call will call to 567110 NOTE:

The mentioned parameters and network settings in this sample be carefully modified to meet the real-world applications.

Dialing Procedures

(26)