Cameron Um Bop Ram

(1)

UM Blowout Preventer

Operation and Maintenance Manual

(2)

All the information contained in this manual is the exclusive property of Cooper Cameron Corporation, Cameron Division. Any reproduction or use of the calculations, drawings, photographs, procedures or instructions, either expressed or implied, is forbidden without the written permission of Cameron or its authorized agent.

Initial Release A1

August 2002

Cooper Cameron Corporation Cameron Division

(3)

PREFACE

The procedures included in this book are to be performed in conjunction with the requirements and recommendations outlined in API Specifications. Any re-pairs to the equipment covered by this book should be done by an authorized Cameron service representative. Cameron will not be responsible for loss or ex-pense resulting from any failure of equipment or any damage to any property or injury or death to any person resulting in whole or in part from repairs per-formed by other than authorized Cameron personnel. Such unauthorized re-pairs shall also serve to terminate any contractual or other warranty, if any, on the equipment and may also result in equipment no longer meeting applicable requirements.

File copies of this manual are maintained. Revisions and/or additions will be made as deemed necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions shown are accurate.

This book covers Cameron UM Blowout Preventers, which are products of Cooper Cameron Corporation.

Cooper Cameron Corporation Cameron Division

P.O. Box 1212

Houston, Texas 77251-1212 713-939-2211

(4)

(5)

(in) A-1 A-2 B-1 B-2 C E F G Approx. Weight (lb.)FlgXFlg Approx. Weight (lb.)StdXStd 7-1/16” 3000 7-1/16 78.250” 116.500” 24.062” 17” 20.250” 8.750” 7.844” 5.50” 2600 2477 7-1/16” 5000 7-1/16 78.250” 116.500” 27.500” 16.75” 20.250” 10.406” 9.625” 5.50” 2652 2477 7-1/16” 10,000 7-1/16 78.250” 116.500” 30.562” 15.50” 20.625” 11.062” 12.031” 5.50” 3275 2825 7-1/16” 15,000 7-1/16 78.250” 116.500” 31.812” 15.50” 20.625” 11.688” 12.656” 5.50” 3525 2825 11” 10,000 11 96.250” 146.875” 35.688” 16.63” 25.750” 13.125” 13.844” 6.75” 6400 9650 13-5/8” 10,000 13-5/8 134.500” 201.000” 41.688” 20.26” 30.250” 15.125” 17.094” 7.50” 10,300 10,300

Size Pressure Rating (psi) Vertical Bore (cm) A-1 (cm) A-2 (cm) B-1 (cm) B-2 (cm) C (cm) E (cm) F (cm) G (cm) Approx. Weight (kg)FlgXFlg Approx. Weight (kg)StdXStd 7-1/16” 3000 17.9 199 296 61 43 51 22 20 14 1179 1124 7-1/16” 5000 17.9 199 296 70 43 51 26 24 14 1203 1124 7-1/16” 10,000 17.9 199 296 78 39 53 28 31 14 1486 1281 7-1/16” 15,000 17.9 199 296 81 39 53 30 32 14 1599 1281 11” 10,000 27.9 244 373 91 42 65 33 35 17 2903 2903 13-5/8” 10,000 34.6 342 511 106 51 77 38 43 19 4672 4377

(8)

B*** Height - with 30” spacer

E Centerline of side outlet below rams to bottom flange face

F Top of upper ram to top flange face

G Height of ram

H Centerline of side outlet between rams to bottom flange face

J Top of lower ram to bottom of upper ram

UM BOP Assembly, Double

SD 034560 C B G J E _H F D A

(9)

Size

Pressure Rating

(psi)

Vertical Bore

(in.) A-1 A-2 B-1 B-2 B*** C E F G H J

Approx. Weight (lb.)FlgXFlg Approx. Weight (lb.)StdXStd 7-1/16” 3000 7-1/16 78.250” 116.500” 41.000” 34” 18.562” 20.250” 8.750” 7.844” 5.50” 25.688” 11.438” 5100 4950 7-1/16” 5000 7-1/16 78.250” 116.500” 44.188” 33.50” 18.812” 20.250” 10.406” 9.625” 5.50” 27.094” 11.188” 4904 4729 7-1/16” 10,000 7-1/16 78.250” 116.500” 48.625” 31.50” 17.438” 20.625” 11.062” 12.031” 5.50” 29.125” 12.562” 5850 5500 7-1/16” 15,000 7-1/16 78.250” 116.500” 49.875” 33.50” 17.438” 20.625” 11.688” 12.656” 5.50” 29.750” 12.562” 6100 5500 11” 10,000 11 96.250” 146.875” 55.875” 36.44” 16.562” 25.750” 13.125” 13.844” 6.75” 33.312” 13.438” 11,300 11,300 13-5/8” 10,000 13-5/8 114.125” 172.250” 66.625” 41.26” 12.562” 30.250” 15.125” 17.094” 7.50” 40.062” 17.438” 18,400 18,400 Size Pressure Rating (psi) Vertical Bore (cm) A-1 (cm) A-2 (cm) B-1 (cm) B-2 B*** C (cm) E (cm) F (cm) G (cm) H (cm) J (cm) Approx. Weight (kg)FlgXFlg Approx. Weight (kg)StdXStd 7-1/16” 3000 17.9 199 296 61 86 51 22 20 14 65 29 2313 2245 7-1/16” 5000 17.9 199 296 70 85 51 26 24 14 69 28 2224 2145 7-1/16” 10,000 17.9 199 296 78 80 53 28 31 14 74 32 2654 2495 7-1/16” 15,000 17.9 199 296 81 85 53 30 32 14 76 32 2767 2495 11” 10,000 27.9 244 373 91 93 65 33 35 17 85 34 5126 5126 13-5/8” 10,000 34.6 342 511 106 105 77 38 43 19 102 44 8346 8346

(10)

E Centerline of side outlet to bottom flange face

F Top of ram to top flange face

G Height of ram

UM BOP Assembly, Single with Tandem Boosters

SD 034566 A C B E F G D

(11)

Size

Pressure Rating

(psi)

Vertical Bore

(in) A-1 A-2 B-1 B-2 C E F G

Approx. Weight (lb.)FlgXFlg Approx. Weight (lb.)StdXStd 13-5/8” 10,000 13-5/8” 169.125” 235.875” 41.688” 30.88” 30.50” 15.125” 17.094” 7.5” 11,600 11,000 Size Pressure Rating (psi) Vertical Bore (cm) A-1 (cm) A-2 (cm) B-1 (cm) B-2 C (cm) E (cm) F (cm) G (cm) Approx. Weight (kg)FlgXFlg Approx. Weight (kg)StdXStd 13-5/8” 10,000 34.6 430 599 106 78 77 38 43 19 5262 4990

(12)

UM BOP, 7-1/16” SD 034510 23 31 43 3 6 35 37 5 33 34 40 26 22 39 20 38 24 25 36 50 2 19 18 16 21 54 55 1 44 12 13 11 10 51 27 28 29 34 33 4 37 6 35 53 52 67 56 15 14 17 66

(13)

Item No. Description Qty - Single Qty - Double 7-1/16” 5000 psi Model II 7-1/16” 10,000 psi Model II 7-1/16” 15,000 psi Model II 1 Body 1 1 ---- ---- ----2 Bonnet 2 4 2010585-01 2010584-01 2010515-03 3 Operating Piston 2 4 2010559-02 2010559-01 2010559-01 4 Ram Change Piston, Open 2 4 2011075-01 2011075-01 2011075-01 5 Ram Change Piston, Close 2 4 2011073-01 2011073-01 2011073-01 6 Ram Change Cylinder 4 8 2011074-01 2011074-01 2011074-01 10 Pin, Ram Guide 4 8 030313-02 030313-02 030313-02 11 Check Valve 2 4 M517988 M517988 M517988 12 Screw, Socket Head Set 2 4 005940-09 005940-09 005940-09 13 Pipe Plug, Heavy Hex Head 2 4 005930-05-10 005930-05-10 005930-05-10 14 Retainer Ring, Plastic Packing 2 4 2010178-01 2010178-01 2010178-01 15 Energizing RIng 2 4 018586-12 018586-12 018586-12 16 Lip Seal 2 4 212741-37 212741-37 212741-37 17 O-Ring 2 4 018492-92 018492-92 018492-92 18 Retainer, Lip Seal 2 4 689523-04 689523-04 689523-04 19 Retaining Ring, Spirolox 2 4 018572-83 018572-83 018572-83 20 Locking Screw 2 4 2010519-01 2010519-01 2010519-01

21 Ring Gasket 4 8 ---- 021792-21

----22 Locking Screw Housing 2 4 2010530-01 2010530-01 2010530-01 23 Operating Cylinder 2 4 2010529-02 2010529-02 2010529-02 24 Cylinder Head Weldment 2 4 2011328-01 2011328-01 2011328-01 25 Stud, Double Ended 8 16 2010189-19 2010189-19 2010189-19 26 Nut, Heavy Hex 8 16 2709000-13-01 2709000-13-01 2709000-13-01 27 Seal Ring 2 4 2708749-01 2708749-01 2708749-01 28 Retainer Ring, Tail Rod 2 4 2010527-01 2010527-01 2010527-01 29 Retaining Ring, Spirolox 2 4 041008-02-93-32 041008-02-93-32 041008-02-93-32

30 Seal RIng 2 4 2710280 2710280 2710280

31 O-Ring 4 8 702645-37-61 702645-37-61 702645-37-61 32 O-Ring 2 4 702645-26-91 702645-26-91 702645-26-91

33 Seal RIng 4 8 2724047 2724047 2724047

34 Wear Ring, Ram Change Piston 4 8 049223-28 049223-28 049223-28 35 O-Ring 8 16 702645-33-71 702645-33-71 702645-33-71 36 O-Ring 4 8 702645-32-81 702645-32-81 702645-32-81 37 O-Ring 8 16 702645-32-41 702645-32-41 702645-32-41 38 Stud, Double Ended 16 32 ---- 219065-08-03-61 219065-08-03-61 39 Nut, Heavy Hex 16 32 ---- 2709000-08-01 2709000-08-01

40 Lifting Eye 4 8 011849 011849 011849

41 Split Retainer Ring 2 4 2010599-01 2010599-01 2010599-01 42 Concentric Booster Ring 2 4 2010600-01 2010600-01 2010600-01

43 Seal Ring 2 4 710541 710541 710541 44 Plastic Packing 10 20 007650-08 007650-08 007650-08 46 Blind Plug 4 8 017454-09 ---- 017454-09 47 Pipe Plug 4 8 002504-04 ---- 002504-04 48 Tubing Gland 4 8 017454-08 ---- 017454-08 66 Name Plate 1 1 2032175-03 2032175-01 ----67 Name Plate 1 ---- 025950 025950 ----50 Bonnet Bolt 8 16 2010514-02 2010514-03 ----51 Bonnet Seal (Carrier Type) 4 8 ---- ---- ----51A Bonnet Seal (Face Type) 2 4 644197-01-00-01 644197-01-00-01 644197-01-00-01

52 Stud, Double Ended 12 ---- ---- 219067-14-07-41 ----53 Nut, Heavy Hex 12 ---- ---- 2709000-14-01 ----54 Stud, Double Ended 16 ---- ---- 219067-08-03-61 ----55 Nut, Heavy Hex 16 ---- ---- 2709000-08-01

----56 Name Plate 1 1 ---- 236606-01

----66 Name Plate 1 1 2032175-03 2032175-01

----67 Name Plate 1 ---- 025950 025950

----Accessory Items

Ram Change Piston Cover 2 4 645046-17 645046-17 645046-17 Standard Accessory Items 1 1 697149-01 697149-02 697149-02 Locking Screw Accessory Items 2 4 ---- 697150-01 697150-01

Expendable Items

Ring Gasket 2 4 702002-03-52 702003-15-22 702003-15-22 Ring Gasket 2 4 702002-04-62 702003-15-62 702003-15-62

(14)

UM BOP, 11” SD 034498 23 21 6 33 35 30 32 28 4 35 6 33 5 28 32 38 26 22 31 3 17 24 36 20 37 25 40 42 2 78 10 62 15 14 17 86 87 34 52 74 41 29 12 13 11 19 18 16 43 1

(15)

Item No. Description Qty - Single Qty - Double 11” 3000 psi 11” 5000 psi 11” 10,000 psi 11” 15,000 psi 1 Body 1 1 ---- ---- ----

----2 Bonnet (Seal Carrier) 2 4 ---- ---- ---- ----2A Bonnet (Face Seal) 2 4 ---- 2011152-01 2164126-01 ----3 Piston Subassembly 2 4 ---- 2011173-01 2011173-01 ----4 Ram Change Piston - Open 2 4 ---- 2011155-01 2011155-01 ----4A Ram Change Piston - Open, Special ---- ---- ---- ---- ---- ----5 Ram Change Piston - Close 2 4 ---- 2011144-01 2011144-01 ----5A Ram Change Piston - Close, Special ---- ---- ---- ---- ---- ----6 Ram Change Cylinder 4 8 ---- 2011154-01 2011154-01

----8 O-Ring ---- ---- ---- ---- ----

----9 Ram Change Piston Cap ---- ---- ---- ---- ---- ----10 Ram Guide Pin 4 8 ---- 030313-03 030313-03

----11 Check Valve 2 4 ---- M517988 M517988

----12 Set Screw, Socket Head 2 4 ---- 005940-09 005940-09 ----13 Pipe Plug 2 4 ---- 005930-05-10 005930-05-10

----14 O-Ring 2 4 ---- 2010178-02 2010178-02

----15 Energizing Ring 2 4 ---- 018586-13 018586-13 ----16 Lip Seal 2 4 ---- 212741-38-00-01 212741-38-00-01

----17 O-Ring 6 12 ---- 018492-91 018492-91

----18 Retainer, Lip Seal 2 4 ---- 689523-05 689523-05 ----19 Retaining Ring, Spirolox 2 4 ---- 018572-84 018572-84 ----20 Locking Screw 2 4 ---- 046628-01 046628-01 ----21 O-Ring 4 8 ---- 702645-38-21 702645-38-21 ----22 Locking Screw Housing 2 4 ---- 2011168-01 2011168-01 ----23 Operating Cylinder 2 4 ---- 2011172-01 2011172-01 ----24 Cylinder Head Weldment 2 4 ---- 2011167-01 2011167-01 ----25 Stud, Double Ended 8 16 ---- 219065-17-20-01 219065-17-20-01

----26 Nut 8 16 ---- 2164777-01 2164777-01 ----28 O-Ring 4 8 ---- 702645-33-31 702645-33-31 ----29 Plastic Packing 10 20 ---- 007650-25 007650-25 ----30 Seal Ring 2 4 ---- 2724061 2724061 ----31 Wear Ring 2 4 ---- 049223-31 049223-31 ----32 Wear Ring 4 8 ---- 049223-32 049233-32 ----33 O-Ring 8 16 ---- 702645-33-91 702645-33-91 ----34 O-Ring 4 8 ---- 702645-33-01 702645-33-01 ----35 O-Ring 8 16 ---- 702645-32-61 702645-32-61 ----36 Stud, Double Ended 16 32 ---- 219065-12-05-01 219065-12-05-01 ----37 Nut 16 32 ---- 2709000-12-01 2709000-12-01

----38 Lifting Eye 2 4 ---- 011849 011849

----40 Blind Plug 4 8 ---- 017454-09 017454-09 ----41 Plug, Pipe, Threaded 4 8 ---- 002504-04 002504-04 ----42 Tubing Gland 4 8 ---- 017454-08 017454-08 ----43 Ring Gasket 4 8 ---- 021792-22 021792-22 ----52 Bonnet Bolt 8 16 ---- 2010962-01 2164128-01

----62 Bonnet Seal 4 8 ---- ---- ----

----62A Bonnet Seal (Face Type) 2 4 ---- 644197-02-00-01 644197-02-00-01 ----74 O-Ring 8 16 ---- 702645-22-91 702645-22-91 ----78 Lifting Eye 2 2 ---- 011849 011849 ----96 Name Plate 1 1 ---- 2032175-03 2032175-03 ----97 Name Plate 1 1 ---- 025950 025950 ----Accessory Items Standard Accessories 1 1 ---- 697149-02 697149-02 ----Locking Screw Accessories 2 4 ---- 697150-02 697150-02 ----Cover, Ram Change Pistons 2 2 ---- 645046-18 645046-18

----Expendable Items

(16)

----UM BOP, 13-5/8” SD034538 39 29 12 26 32 11 12 43 12 14 43 14 43 24 42 41 11 25 14 43 43 40 16 19 17 18 51 3 28 27 14 12 11 3 30 50 33 11 43 40 2 42 41 75 1 66 65 64 71 70 74 76 10 78 22 20 45 9 8 35 5 4 37 36 6 36 31 23 31 38 15 See Detail “A” Detail “A”

(17)

Item No. Description Qty - Single Qty - Double 13-5/8” 5000 psi 13-5/8” 10,000 psi 13-5/8” 15,000 psi 1 Body 1 1 ---- ----

----2 Bonnet (Seal Carrier) 2 4 ---- 2164340-01(02) ----2A Bonnet (Face Seal) 2 4 ---- 2164343-01(02) ----3 Piston Subassembly (2) (4) ---- 2164345-01 ----4 Ram Change Piston - Open 2 4 ---- 2164433-02 ----4A Ram Change Piston - Open, Special 2 4 ---- 2164433-01 ----5 Ram Change Piston - Close 2 4 ---- 2164434-02 ----5A Ram Change Piston - Close, Special 2 4 ---- 2164434-01 ----6 Ram Change Cylinder 4 8 ---- 2164347-02 ----6A Ram Change Cylinder, Special 4 8 ---- 2164347-01

----8 O-Ring 4 8 ---- 702645-35-71

----9 Ram Change Piston Cap 4 8 ---- 2164342-02 ----9A Ram Change Piston Cap, Special 4 8 ---- 2164342-01

----10 Ram Guide Pin 4 8 ---- 030313-01

----11 Retainer Ring, Spirolox, Operating Piston 8 16 ---- 708758

----12 Retainer, Polypak 8 16 ---- 689523-06

----14 Seal Polypak 8 16 ---- 2724613-01

----15 Wear Ring, Ram Change Piston 4 8 ---- 2164449-01

----16 Check Valve 2 4 ---- M517988

----17 Screw, Socket Head 2 4 ---- 005940-09

----18 Pipe Plug 2 4 ---- 005930-05-10

----19 Packing, Plastic 2 4 ---- 007650-25

----20* Locking Screw 2 4 ---- 695234

----22* Locking Screw Housing 2 4 ---- 2164346-01 ----23 Operating Cylinder 2 4 ---- 2164348-02 ----23 Operating Cylinder, Special 2 4 ---- 2164348-01

----24 Cylinder Head 2 4 ---- 2164341-02

----24 Cylinder Head, Special 2 4 ---- 2164341-01

----25 Cylinder Stud 24 48 ---- 2164361-01

----26 Nut, Cylinder 24 48 ---- 2709000-12-22 ----27 Retainer Ring, Plastic Packing 2 4 ---- 012469-24

----28 Energizing Ring 2 4 ---- 018586-01

----29 Wear Ring, Operating Piston 2 4 ---- 049223-31

----30 Seal Ring 2 4 ---- 2724061

----31 O-Ring 4 8 ---- 702645-38-21

----32 Washer, Cylinder Stud 24 48 ---- K220607 ----33 Washer, Bonnet Bolt 8 16 ---- 2164450-01

----35 O-Ring 4 8 ---- 702645-33-81

----36 O-Ring 8 16 ---- 702645-34-61

----37 O-RIng 8 16 ---- 702645-32-41

----37A O-RIng, Special for V Threaded Ram Change Piston 8 16 ---- 702645-32-81

----38 O-Ring 4 8 ---- 702645-33-31

----39* Screw 16 32 ---- 702585-25-00-30

----40 Lifting Eye 4 8 ---- 011849

----41 Tubing Gland 4 8 ---- 017454-08

----42 Blind Plug 4 8 ---- 017454-09

----43 Pipe Plug, Pressure 12 24 ---- 002504-14

----45 Pipe Plug, Threaded 4 8 ---- 203682

----50 Bonnet Bolt 8 16 ---- 2164362-01 ----51 O-Ring 8 16 ---- 2164718-01 ----64 Name Plate 1 1 ---- 025950 ----65 Name Plate 1 1 ---- 2032175-03 ----66 Name Plate 1 1 ---- 236606-01 ----70 Lifting Lug 2 2 ---- 2164420-01 ----71 Screw, Cap 8 8 ---- 702546-31-00-34

----74 Stud, Top End Connection 20 20 ---- 219065-17-10-71 ----75 Nut, Top End Connection 20 20 ---- 2709000-17-01

----76 Pipe Plug 2 4 ---- 201019

----77 Bonnet Seal Carrier 2 4 ---- 645507-01-00-01 ----78 Bonnet Seal (for Carrier) 4 8 ---- 645509-01-00-01 ----78A Bonnet Seal (Face Type) (2) (4) ---- 644197-03-00-01

----79 O-Ring 2 4 ---- 702645-56-91

----80** Tandem Booster Assembly (Qty. 1 for 2 Bonnets) 1 1 ---- 2164649-01

----Accessory Items

Standard Accessories 1 1 ---- 697149-12 ----Locking Screw Accessories 2 4 ---- 697150-02

----Spanner Wrench 1 1 ---- 2164429-01

----Expendable Items

Ring Gaskets (Top & Bottom Connection) 2 2 ---- 702003-15-92

----Eyebolt 2 2 ---- 700734

----Paste 1 1 ---- 705444

----Loctite Adhesive 1 1 ---- 708740

----Thread Sealant 1 1 ---- 711706

----*Not Required When Using Wedgelocks or Tandem Boosters **Optional Tandem Boosters

(18)

Tandem Booster Assembly

SD 034536 16 1 7 17 5 13 12 6 15 14 3 11 10 9 24 23 4 29 25 29 28 30 8 26 27

(19)

Tandem Boosters for UM BOPs

A BOP equipped with tandem boosters can deliver increased shearing force while not in-creasing the wear and tear on the packers. Tandem boosters approximately double the force available to shear pipe. Since the tailrod of the tandem booster has the same stroke as the BOP’s operating piston, the standard shear locking mechanism can be installed on the outside end of the booster. For information on lock screws and the required spacers, see page 17.

For information concerning applications where a tandem booster is required, consult your Cameron representative.

Item Number Description Qty. _{13-5/8” 10,000 psi WP}Part Number

1 Adapter 2 2164650-01 3 Cylinder 2 2010884-01 4 Cylinder Head 2 2010882-02 5 Tail Rod 2 2010880-01 6 Piston 2 645172-03 7 Screw, 12 Pt Cap 16 702585-25-00-30 8 Screw, 12 Pt Cap 12 702585-34-01-54 9 O-Ring 2 702645-33-71 10 Seal, Lip 2 011741-34 11 O-Ring 2 702645-38-12 12 Seal Ring 2 710418 13 Wear Ring 2 645215-01 14 Wear Ring 2 049223-01 15 Seal Ring 2 704772

16 Filter, Muffler, Quiet Flow 2 2724042

17 Stud, Continuous Thread 2 702533-09-10-22

23 Gland, Tubing 2 017454-08

24 Blind Plug 2 017454-09

25 Plug, Pipe-Threaded Hex Socket 2 002504-28

26 Tubing, Hydraulic 2 2711865-12-11

27 Bushing, Pipe 2 K194489

28 Bushing, Pipe 2 203098

29 Connector, Tubing, Male 4 204887-08-05-17

(20)

SD 034582 Pipe Bonnet Shear Bonnet Close Pressure Open Pressure

UM BOP Open and Close Hydraulics (13-5/8” 10,000 Shown) Pipe Bonnet Shear Bonnet Close Pressure Open Pressure

(21)

Bore Size and Working Pressure

Gals to Open Pipe Rams (1 set)

Gals to Close Pipe Rams (1 set)

Gals to Close Shear Rams (1 set)

Closing Area (Sq. inches)

Locking Screw Turns (Each End) Closing Ratio Opening Ratio 7-1/16” All WP _2.2 _2.3 _2.4 _67.3 ₁₈ _11.7:1 _3.8:1 11” Except 15,000 psi 6.2 6.2 7.4 113.8 27 13.7:1 3.7:1 11” 15,000 psi - - - -13-5/8” Except 15,000 psi 7.5 7.5 8.8 110.15 32 8.7:1 2.3:1 13-5/8” 15,000 psi Model B - - -

-Bore Size and Working Pressure

Liters to Open Pipe Rams (1 set)

Liters to Close Pipe Rams (1 set)

Liters to Close Shear Rams (1 set)

Closing Area (Sq. cm)

Locking Screw Turns (Each End) Closing Ratio Opening Ratio 7-1/16” All WP _8.3 _8.7 _9.1 ₄₃₄ ₁₈ _11.7:1 _3.8:1 11” Except 15,000 psi 23.5 23.5 28.0 734 27 13.7:1 3.7:1 11” 15,000 psi - - - -13-5/8” Except 15,000 psi 28.4 28.4 33.3 711 32 8.7:1 2.3:1 13-5/8” 15,000 psi Model B - - -

-UM BOP Tandem Booster Operating Data and Fluid Requirements*

Gals to Open Pipe Rams (1 set)

Gals to Close Pipe Rams (1 set)

Closing Area (Sq. inches)

Locking Screw Turns

(Each End) Closing Ratio Opening Ratio

7-1/16” All WP _- _- _- _- _- _3.8:1 11” Except 15,000 psi 6.2 13.1 201.8 27 24.3:1 3.7:1 11” 15,000 psi _- _- _- _- _- -13-5/8” Except 15,000 psi 7.5 10.4 198 32 15.6:1 2.3:1 13-5/8” 15,000 psi Model B - - -

-*All volumes based on shear ram configuration

Liters to Open Pipe Rams (1 set)

Liters to Close Pipe Rams (1 set)

Closing Area (Sq. cm)

Locking Screw Turns

(Each End) Closing Ratio Opening Ratio

7-1/16” All WP _- _- _- _- _- _3.8:1 11” Except 15,000 psi 23.5 49.6 1302 27 24.3:1 3.7:1 11” 15,000 psi _- _- _- _- _- -13-5/8” Except 15,000 psi 28.4 39.4 1277 32 15.6:1 2.3:1 13-5/8” 15,000 psi Model B - - -

(22)

UM BOP Specifications and Accessories

The following specifications apply to typical Cameron UM type BOPs. Your Cameron rep-resentative can provide information on non-standard BOP assemblies.

• Side outlets to 4-1/16” can be provided beneath each set of rams on either or both sides of UM BOPs. Side outlets can be studded, open-face flange or clamp hub with the same pressure rating as the vertical run connections.

• Flanges conform to API standard 6A and/or 16A. Hubs conform to API 16A or applicable standards. Type 6BX flanges are standard for 10,000 and 15,000 psi working pressures and for 5000 psi for 13-5/8” BOPs.

• Hydraulic control connections for operation of rams and bonnets are 1” NPT. There are two connections for each set of rams.

UM BOP Standard Accessories

Size and Working Pressure Ram Lube* Cameron Box Wrench* Allen Wrench* Packing

Screw Handwheel** Universal Joint** Extension Wrench*

7-1/16” 3000 psi 713878 713114-08 8721-01 5457 6018-01 5652 7-1/16” 5000 psi 713878 7957-06 8721-01 5457 6018-01 5652 7-1/16” 10,000 and 15,000 psi 713878 713114-10 8721-01 5457 6018-01 5652 11” 3000, 5000 and 10,000 psi 713878 713114-10 8721-01 5298 6018-03 5526 11” 15,000 psi 713878 713114-13 8721-01 5298 6018-03 5526 13-5/8” 3000 and 5000 psi 713878 7959-08 8721-01 5298 6018-03 5526 13-5/8” 10,000 psi 713878 713114-10 8721-01 5298 6018-03 5526 13-5/8” 15,000 psi 713878 *** 8721-01 5298 6018-03 5526

(23)

UM BOP Ram Hang-Off Weights and

Shear Requirements

Hang-Off Weights

Hang-off weights are estimated capacities with hardened top corners of the hang-off rams. This enables the rams to dig into the tool joint and provide superior hang-off capac-ity while still meeting NACE requirements.

For variable bore rams (VBRs) and FLEXPACKER rams, hang-off weights up to 300,000 lb (136,078 kg) on hang-off rams for the lower pipe size in the range, 600,000 lb (272,155 kg) for the larger pipe size in the range.

Drill Pipe Shearing Requirements

The minimum shearing configurations needed for each size UM BOP to meet the require-ments of the second edition of API 16A are listed in the following chart. Each shearing configuration is capable of shearing the corresponding pipe at a closing pressure equal to or less than 2800 psi. For further information on shearing requirements for different pipe sizes and grades, contact your Cameron representative.

Minimum Shearing Configurations for the UM BOP

API Designated Size Ram Type Pressure Rating (psi) Pipe OD (In.) Pipe lb/ft Pipe Grade Shearing Configuration

7-1/16” SBR All 3-1/2 13.3 S Shear Bonnets with Tandem Boosters 11” SBR 10,000 and Lower 5 19.5 E Shear Bonnets with Tandem Boosters 11” DS 10,000 and Lower 5 19.5 E Large Bore Shear Bonnets 11” SBR 15,000 and Higher 5 19.5 G Large Bore Shear Bonnets 13-5/8” SBR 10,000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters 13-5/8” DS 10,000 and Lower 5 19.5 G Large Bore Shear Bonnets 13-5/8” SBR 15,000 and Higher 5 19.5 S Large Bore Shear Bonnets

(24)

SD 017508

Top Seal

Ram Packer

U and UM BOP Pipe Rams

Pipe rams are available for use in Cameron UM BOPs to fit all commonly used sizes of tub-ing, drill pipe, drill collar or casing within the ranges in the charts on pages 25, 26, and 27. Cameron pipe rams include the following features:

• Cameron pipe rams are self-feeding and incorporate a large reservoir of packer rubber to ensure a long-lasting seal under all conditions.

• Ram packers lock into place and are not dislodged by well flow.

• All Cameron pipe rams are suitable for H2S service per NACE MR-01-75.

• CAMRAM™ top seals are standard for all U and UM BOP pipe rams from 7-1/16” through 18-3/4” sizes. Packer part numbers beginning with 644xxx indicate the

CAMRAM lipped-plate design. All other packers use standard elastomer material and reinforcement plates.

• CAMRAM 350™ packers and top seals are available for high temperature service and

(25)

U and UM BOP Pipe Ram Part Numbers

Pipe Size (in.) 7-1/16” 3000, 5000, 10,000, and 15,000 psi WP Top Seal 644214-01-00-01 11” 3000, 5000, and 10,000 psi WP Top Seal 644217-01-00-01 11” 15,000 psi WP Top Seal 2010453-01 13-5/8” 3000, 5000, and 10,000 psi WP Top Seal 644223-01-00-01 Assembly Ram Packer Assembly Ram Packer Assembly Ram Packer Assembly Ram Packer

Blind 644504-01 644500-01-00-02 644215-01-00-01 644219-01 044118-01 644218-01-00-01 644222-01 044121-01 644221-01 644225-01 044147-01-00-01 644224-01-00-01 1.050 644504-02 644501-01 644215-02 - - - -1.315 644504-03 644501-02 644215-03 044233-25 044118-07 019243-08 - - - 644225-02 044148-06 644224-02 1.660 644504-04 644501-03 644215-04-00-01 044233-02 044118-02 019243-06 644222-02 044121-02 644221-02 644225-03 044148-05 644224-03 1.900 644504-05 644501-04 644215-05-00-01 044233-03 044118-03 019243-05 644222-03 044121-03 644221-03 644225-04 044148-07 644224-04 2.062 644504-06 644501-05 644215-06 044233-04 044118-04 019243-04 644222-04 044121-04 644221-04 644225-05 044148-03 644224-05 2.375 644504-07 644501-06 644215-07-00-01 644219-06 044118-05 644218-06-00-01 644222-05 044121-05 2010454-05 644225-06 044148-01-00-01 644224-06-00-01 2.875 644504-08 644501-07 644215-08-00-01 644219-07 044118-06 644218-07-00-01 644222-06 044121-06 2010454-06 644225-07 044148-02-00-01 644224-07-00-01 3.500 644504-09 644502-01-00-01 644215-09-00-01 644219-08 644835-01-00-02 644218-08-00-01 644222-07 644753-01 2010454-07 644225-08 644738-01-00-01 644224-08-00-01 4.000 644504-11 644503-02 644215-11-00-01 644219-10 044119-02 644218-10-00-01 044234-10 044122-04 644218-13 644225-10 044149-02 644224-10-00-01 4.500 644504-12 644503-03 644215-12-00-01 644219-11 644835-02 644218-11-00-01 644222-09 644753-02 2010454-09 644225-11 644738-02 644224-11-00-01 4.750 - - - 044233-12 044119-04 644218-13 - - - 644225-13 044150-01 644224-13 5.000 644504-14 644503-05 644215-14-00-01 644219-14 644835-03-00-01 644218-14-00-01 644222-10 644753-03 2010454-10 644225-14 644738-03-00-01 644224-14-00-01 5.500 644504-15 644503-06 644215-15-00-01 644219-16 044120-01 644218-16-00-01 044234-13 044123-01 2010454-11 644225-16 044150-03 644224-16-00-01 5.750 - - - 044233-23 044120-10 644218-17 - - - -5.875 - - - 644225-30 644738-06-00-01 644224-29-00-01 6.000 - - - 044233-16 044120-02 644218-18-00-01 044234-14 044123-02 690808-13 044244-13 044150-04 644224-17 6.625 - - - 044233-17 644835-04 644218-19-00-01 044234-15 044123-03 690808-14 644225-18 644738-04-00-02 644224-18-00-01 7.000 - - - 044233-18 044120-04 644218-20-00-01 044234-16 044124-01 2010454-14 644225-19 044151-01-00-01 644224-19-00-01 7.625 - - - 044233-19 044120-05 644210-21-00-01 044234-17 044124-02 690808-16 644225-20 044151-02 644224-20-00-01 7.750 - - - 044233-22 044120-09 644218-22-00-01 - - - 044244-25 044151-06 644224-21 8.625 - - - 044233-20 044120-06 644218-23-00-01 - - - 044244-16 044151-03 644224-22 9.000 - - - 044244-24 044151-04 019506-06 9.625 - - - 644225-24 044151-05-00-01 644224-24-00-01 10.750 - - - 644225-25 044152-01 644224-25-00-01 11.750 - - - 044244-26 614208-01 644224-26-00-01 3.500 Aluminum 644504-10 644503-01 644215-10 044233-08 044119-06 644218-09 - - - 044244-20 044149-04 644224-09 4.500 Aluminum 644504-13 644503-04 644215-13 044233-11 044119-07 644218-12 - - - 044244-10 044149-05 031215-17 5.000 Aluminum - - - 044233-24 044119-08 644218-15 - - - 044244-32 044150-08 031215-27 SD 017508 Top Seal Ram Packer

(26)

SD 017508

Top Seal

Ram Packer

U and UM BOP Pipe Ram Part Numbers

Pipe Size (in.) 13-5/8” 15,000 psi Top Seal 644226-01-00-01 16-3/4” 3000, 5000, and 10,000 psi Top Seal 644229-01-00-01 18-3/4” 10,000 psi Top Seal 644232-01-00-01 21-1/4” 5000 and 10,000 psi Top Seal 2010939-01 Assembly Ram Packer Assembly Ram Packer Assembly Ram Packer Assembly Ram Packer

Blind 644228-01 044143-01 644227-01-00-01 644231-01 044179-01 644230-01-00-01 644234-01 044184-01 644233-01 044262-01 044214-01 2010851-19 1.050 - - - -1.315 - - - -1.660 - - - -1.900 - - - 644231-02 044180-03 644230-02-00-01 - - - -2.062 044243-02 044144-03 040910-20 - - - -2.375 644228-03 044144-01 644227-03-00-01 644231-03 044180-01 644260-03 044254-02 044185-01 644233-02 044262-02 044215-01 2010851-01 2.875 644228-04 044144-02 644227-04-00-01 644231-04 044180-02 644230-04 044254-03 044185-02 644233-03 044262-03 044215-02 2010851-02 3.500 644228-05 644739-01 644227-05-00-01 644231-05 644740-01 644230-05-00-01 644234-04 644741-01 644233-04-00-01 44262-04 644743-01 2010851-03 4.000 644228-07 044144-06 644227-07 644231-06 044181-02 644230-06 044254-06 044185-05 644233-06 044262-06 044215-05 040962-04 4.500 644228-08 644739-02 644227-08-00-01 644231-07 644740-02 644230-07-00-01 044254-07 644741-02 644233-07 044262-07 644743-02 2010851-05 4.750 044243-10 044145-01 040910-07 644231-08 044181-04 644230-08-00-01 044254-09 044185-08 041856-06 044262-09 044215-08 040962-06 5.000 644228-11 644739-03 644227-11-00-01 644231-09 644740-03 644230-09-00-01 644234-10 644741-03 644233-10-00-01 044262-10 644743-03 2010851-07 5.500 044243-12 044145-03 644227-12-00-01 644231-10 044181-06 644230-10-00-01 044254-11 044185-10 644233-11 044262-11 044215-10 2010851-08 5.750 - - - -5.875 2164172-07 2724029-06 644227-24-00-01 644231-22 2724030-06 644230-23 644234-21 2724031-06 644233-21-00-01 044262-32 2724033-06 2010851-29 6.000 044243-14 044145-04 040910-09 644231-11 049291-01 644230-11 044254-13 044185-12 041856-09 044262-13 044215-12 040962-09 6.625 044243-15 644739-04 644227-14 644231-12 049291-02 644230-12 044254-14 044185-13 644233-13 044262-14 044215-13 2010851-10 7.000 044243-16 044146-01 644227-15-00-01 644231-13 049291-03 644230-13 044254-15 044185-14 644233-14 044262-15 044215-14 2010851-11 7.625 044243-17 044146-02 644227-16-00-01 644231-14 049291-04 644230-14 044254-16 044185-15 041856-12 044262-16 044215-15 040962-12 7.750 044243-22 044146-07 644227-17 - - - -8.625 044243-18 044146-03 040910-13 644231-15 049291-06 644230-15-00-01 044254-17 044185-16 041856-13 044262-17 044215-16 040962-13 9.000 044243-19 044146-04 040910-14 644231-16 049291-07 644230-16-00-01 044254-18 044185-17 041856-14 044262-18 044215-17 040962-14 9.625 044243-20 044146-05 644227-20-00-01 644231-17 049292-01 644230-17-00-01 044254-19 044185-18 644233-18 044626-19 044215-18 040962-15 10.750 044243-21 044146-06 644227-21-00-01 644231-18 049292-02 644230-18-00-01 044254-21 044185-21 644233-19 044262-20 044216-01 040962-20 11.750 - - - 644231-19 049292-03 644230-19-00-01 - - - 044262-21 044216-02 2010851-20 13.375 - - - 644231-20 049292-04 644230-20-00-01 044254-22 044185-20 644233-20 044262-22 044216-03 2010851-22 13.625 - - - 044262-24 044216-05 040962-24 13.750 - - - -16.000 - - - 044262-23 044216-04 2010851-23 3.500 Aluminum 044243-06 044144-05 644227-06 - - - 044254-05 044185-04 041856-16 044262-05 044215-04 040962-16 4.500 Aluminum 044243-08 044144-08 040910-05 - - - 044254-08 044185-07 041856-17 044262-08 044215-07 040962-17 5.000 Aluminum - - -

(27)

-U and -UM BOP Pipe Ram Part Numbers

Pipe Size (in.) 21-1/4” Bore 2000 psi 20-3/4” Bore 3000 psi Top Seal 2163621-01 26-3/4” Bore 2000 and 3000 psi Top Seal 2163566-01

Assembly Ram Packer Assembly Ram Packer

Blind 044256-01 044149-01 2163612-01 044260-01 044209-01 2163561-01 1.050 - - - -1.315 - - - -1.660 - - - -1.900 - - - -2.062 - - - -2.375 - - - 044260-02 614017-01 2163559-01 2.875 - - - 044260-03 614017-02 2163559-02 3.500 044256-02 645328-01 2163613-03 044260-04 614018-01 2163599-03 4.000 044256-03 044192-02 031228-04 044260-05 614018-02 2163599-04 4.500 044256-04 645328-02 2010583-05 044260-06 614018-03 2163599-05 4.750 044256-05 044192-04 031228-06 - - -5.000 044256-06 645328-03-00-01 2163613-06 044260-07 614018-04 2163599-06 5.500 044256-07 044193-02 2163613-07 044260-08 614018-05 2163599-07 5.750 - - - -5.875 044256-32-00-01 645328-05-00-01 2163613-18 - - -6.000 044256-08 044193-03 031228-09 044260-09 614019-01 2163559-08 6.625 044256-09 645328-04 2010583-10-01 044260-10 614019-02 2163559-09 7.000 044256-10 044193-05 031228-11 044260-11 614019-03 2163559-10 7.625 044256-11 044193-06 031228-12 044260-12 614019-04 2163559-01 7.750 - - - -8.625 044256-13 044193-08 031228-14 - - -9.000 044256-14 044193-09 031228-15 044260-14 614019-06 2163599-13 9.625 044256-15 044193-10 031228-16 044260-15 614020-01 2163599-14 10.750 044256-16 044194-01 2010583-17 044260-16 614020-02 2163599-15 11.750 044256-17 044194-02 031228-18 044260-17 614020-03 2163599-16 13.375 044256-18 044194-03 2163613-15 044260-18 614020-04 2163599-17 13.625 044256-21 044194-05 031228-24 - - -13.750 044256-19 044194-04 031228-19 - - -16.000 044256-20 044195-01 2010583-21 044260-19 614021-01 2163559-18 18.625 044256-22 614459-01 031228-25 - - -20.000 - - - 044260-20 614021-02 2163559-21 SD 017508 Top Seal Ram Packer

(28)

U and UM BOP Shearing Blind Rams

Cameron shearing blind rams shear the pipe in the hole, then bend the lower section of sheared pipe to allow the rams to close and seal. Shearing blind rams can be used as blind rams during normal drilling operations.

The DS shearing blind ram can cut larger diameter tubulars or multiple tubing strings regardless of their orientation to the centerline of the ram. A blade seal between the up-per and lower faces eliminates the need for moving pipe after shearing.

Features of shearing blind rams and DS rams include:

• Large frontal area on the blade face seal reduces pressure on the rubber and increases service life.

• Cameron SBRs can cut pipe numerous times without damage to the cutting edge. • The single-piece body incorporates an integrated cutting edge.

• CAMRAM™ top seals are standard for all U and UM BOP shearing blind rams

through 18-3/4”. Part numbers beginning with 644xxx indicate CAMRAM. All other top seals are standard elastomer material.

• H2S SBRs are available for critical service applications and include a blade material of

hardened high alloy suitable for H2S service.

• The Cameron shearing blind ram has a single-piece body with an integrated cutting edge.

(29)

U and UM BOP H

2 S Shearing Blind Ram Part Numbers

Severe Service

BOP Bore Size and Working Pressure (psi)

1 Upper Ram Subassembly 2 Ram 3 Blade Packer 4 Packer 5 Packer 6 Top Seal 7 Blade Insert 8 Set Screw 13-5/8” 5000 and 10,000 644781-03-00-01 644780-01-00-01 644834-01-00-01 645427-01-00-01 645428-01-00-01 644707-01-00-01 644581-01-00-01 644582-01 13-5/8” 15,000 2163019-01-02 2163017-01-01 644834-01-00-01 644832-01-00-01 644833-01-00-01 644709-01-00-01 2164281-01 644582-01

9 Lower Ram Subassembly 10 Ram 11 Packer 12 Packer 13 Top Seal 14 Blade Insert 15 Pin 13-5/8” 5000 and 10,000 644781-04-00-01 644780-02-00-01 645427-01-00-01 645428-01-00-01 644707-01-00-01 644581-02-00-01 200231 13-5/8” 15,000 2163019-02-02 2163018-01-01 644832-01-00-01 644833-01-00-01 644709-01-00-01 644581-02-00-01 200231 Standard Service

1 Upper Ram Subassembly 2 Ram 3 Blade Packer 4 Packer 5 Packer 6 Top Seal 7 Blade Insert 8 Set Screw 11” 5000 and 10,000 645011-03-00-01 645009-01-00-01 046910-04-00-01 046751-04-00-01 046752-04-00-01 644217-01-00-01 645010-01-00-01 644582-01 13-5/8” 5000 and 10,000 644781-01-00-01 644780-01-00-01 644435-01-00-01 046751-01-00-02 046752-01-00-02 644223-01-00-01 644581-01-00-01 644582-01 13-5/8” 15,000 2163019-01-01 2163017-01-01 644435-01-00-01 046751-05-00-01 046752-05-00-01 644226-01-00-01 2164281-01 644582-01 18-3/4” 10,000 2010186-01 2010187-01 2010192-01 2010191-01 2010190-01 2010193-01 2010182-01 644524-01

9 Lower Ram Subassembly 10 Ram 11 Packer 12 Packer 13 Top Seal 14 Blade Insert 15 Pin 11” 5000 and 10,000 645011-04-00-01 645009-02-00-01 046751-04-00-01 046752-04-00-01 644217-01-00-01 645010-02-00-01 200231 13-5/8” 5000 and 10,000 644781-02-00-01 644780-02-00-01 046751-01-00-02 046752-01-00-02 644223-01-00-01 644581-02-00-01 200231 13-5/8” 15,000 2163019-02-01 2163018-01-01 046751-05-00-01 046752-05-00-01 644226-01-00-01 644581-02-00-01 200231 18-3/4” 10,000 2010186-02 2010188-01 2010191-01 2010190-01 2010193-01 2010183-01 200231 SD 017509 13 10 12 15 5 7 8 6 2 1 3 4 14 11 9

(30)

SD 017513 6 2 1 4 7 5 3

U and UM BOP Shearing Blind Ram Part Numbers

BOP Bore Size and Working Pressure (psi)

Description and Item Number

Upper Ram Subassy. Body* Blade Packer* Side Packer* Side Packer* Blade Insert*** Set Screw (2 Req.)*** Lower Ram

Subassy.** Body Side Packer Side Packer Top Seal

(2 Req.) Blade Insert*** Spirol Pin (2 Req.) *** 7-1/16” 5000, 10,000 and 15,000 046792-01-00-03 046210-01-00-04 ---- 2010873-02 2010873-01 ---- ---- 046792-02-00-03 046212-01-00-04 2010872-01 ---- 644214-01-00-01 ---- ----11” 5000 and 10,000 645011-03-00-01 645009-01-00-01 046910-04-00-01 046751-04-00-01 046752-04-00-01 645010-01-00-01 644582-01 645011-04-00-01 645009-02-00-01 046751-04-00-01 046752-04-00-01 644217-01-00-01 645010-02-00-01 200231 11” 15,000 2010458-01 2010459-10 046910-04-00-01 2010460-07 2040461-07 ---- ---- 2010458-02 2010459-02 2010460-07 2010461-07 2010453-01 ---- ----13-5/8” 5000 and 10,000 644781-01-00-01 644780-01-00-01 644435-01-00-01 046751-01-00-02 046752-01-00-02 644581-01-00-01 644582-01 644781-02-00-01 644780-02-00-01 046751-01-00-02 046752-01-00-02 644223-01-00-01 644581-02-00-01 200231 13-5/8” 15,000 2163019-01-01 2163017-01-01 644435-01-00-01 046751-05-00-01 046752-05-00-01 2164281-01 644582-01 2163019-02-01 2010292-01 046751-05-00-01 046752-05-00-01 644226-01-00-01 644581-02-00-01 200231 16-3/4” 5000 046766-01-00-01 049006-01-00-01 046910-03-00-01 046751-03-00-01 046752-03-00-01 ---- ---- 046766-02-00-01 049007-01-00-01 046751-03-00-01 046752-03-00-01 644229-01-00-01 ---- ----16-3/4” 10,000 046773-01-00-01 046774-01-00-01 046910-03-00-01 046751-03-00-01 046752-03-00-01 ---- ---- 046773-02-00-01 046775-01-00-01 046751-03-00-01 046752-03-00-01 644229-01-00-01 ---- ----18-3/4” 10,000 2010186-01 2010187-01 2010192-01 2010191-01 2010190-01 2010182-01 644524-01 2010186-02 2010188-01 2010191-01 2010190-01 2010193-01 2010183-01 200231 20-3/4” 3000 046783-01-00-02 046784-01-00-02 ---- 615235-01-00-01 ---- ---- ---- 046783-02-00-02 046785-01-00-02 615247-01-00-01 615247-02-00-01 2163621-01 ---- ----21-1/4” 2000 046783-01-00-02 046784-01-00-02 ---- 615235-01-00-01 ---- ---- ---- 046783-02-00-02 046785-01-00-02 615247-01-00-01 615247-02-00-01 2163621-01 ---- ----21-1/4” 5000 049983-01 049981-01 046910-05-00-01 046751-06-00-01 046752-06-00-01 ---- ---- 049983-02 049982-01 046751-06-00-01 046752-06-00-01 645478-01-00-01 ---- ----21-1/4” 7500 and 10,000 046788-01 049012-01 046910-05-00-01 046751-06-00-01 046752-06-00-01 ---- ---- 046788-02 049011-01 046751-06-00-01 046752-06-00-01 645478-01-00-01 ----

----* Part of Upper Ram Subassembly. ***H2S SBR’s

(31)

Flexpackers for U and UM BOPs

The Cameron FLEXPACKER ram is designed to close and seal around several diameters of tubing and pipe. These packers can be used in existing Cameron BOPs. Features include:

• Stacks of metal inserts bonded into the elastomer move radially in the elastomer as the BOP rams are closed.

As rams are energized, the proper set of metal inserts is forced against the pipe. The top plate of the packer fits the largest diameter of pipe.

FLEXPACKER Sizes and Part Numbers

BOP Size and Working Pressure Pipe Size Range Part Number

11” 3000, 5000 and 10,000 psi, Type U and UM 2-3/8” x 3-1/2” 2011740-01

11” 3000, 5000 and 10,000 psi, Type U and UM 3-1/2” x 5” 2163445-01

13-5/8” 3000, 5000 and 10,000 psi, Type U and UM 2-3/8” x 3-1/2” 2011716-01

13-5/8” 3000, 5000 and 10,000 psi, Type U and UM 3-1/2” x 5” 2011673-01

13-5/8” 3000, 5000 and 10,000 psi, Type U and UM 5” x 6-5/8” 2011688-01

(32)

CAMRAM 350 Packers and Top Seals for

U and UM BOPs

CAMRAM 350 UM BOP pipe ram packers and top seals are available for applications which

require high temperature capabilities and greater H2S resistance than standard CAMRAM

packers and top seals.

CAMRAM 350 is available in all U and UM BOP sizes in which standard CAMRAM packers and top seals are offered. At present, only pipe sizes (up to 5-1/2”) are manufactured.

Pipe Size (in.) 7-1/16” 3000 - 15,000 psi Top Seal 644701-01 11” 3000 - 10,000 psi Top Seal 644703-01 11” 15,000 psi Top Seal 644705-01 13-5/8” 3000 - 10,000 psi Top Seal 644707-01 13-5/8” 15,000 psi Top Seal 644709-01

Packer Packer Packer Packer Packer

Blind 644700-01 644702-01 644704-01 644706-01-00-01 644708-01 2.375 644700-07 644702-06 644704-05 644706-06 644708-03 2.875 644700-08 644702-07 644704-06 644706-07-00-01 644708-04 3.500 644700-09 644702-08 644704-07 644706-08-00-01 644708-05-00-01 4.000 - 644702-10 644704-08 644706-10-00-01 644708-07-00-01 4.500 644700-12 644702-11 644704-09 644706-11-00-01 -5.000 - 644702-14 644704-10 644706-14-00-01 644708-11 5.500 - 644702-16-00-01 - 644706-16 644708-12 5.875 ---- ---- ---- 644706-29-00-01 ----6.625 644706-18 7.000 644702-20 644706-19-00-01 7.625 644702-21 644706-20 9.625 644706-24-00-01 SD 017514 Camram 350 Packer Camram 350 Top Seal

(33)

Bonnet Seals and Connecting Rod Seals

For applications where only bonnet and/or connecting rod seals are required, Cameron of-fers individually packaged components. Connecting rod seals are nitrile rubber. Bonnet seals beginning with 644197 are the newest design.

When high temperature and/or high concentrations of H2S are expected, Cameron

rec-ommends the used of CAMLAST bonnet and connecting rod seals along with CAMRAM 350 packers and top seals.

U and UM BOP CAMLAST Bonnet and Connecting Rod Seals

BOP Size (In.) Pressure Rating (psi) Nitrile CAMLAST

Bonnet Seal Connecting Rod Seal Bonnet Seal Connecting Rod

Seal 7-1/16 3000, 5000, 10,000, and 15,000 644197-01-00-01 212741-37-00-01 644573-01-00-01 645077-37-00-01 11 3000, 5000, and 10,000 644197-02-00-01 212741-38-00-01 644573-02-00-01 645077-38-00-01 11 15,000 Model 79 049272-03 212741-38-00-01 644898-01 645077-38-00-01 13-5/8 3000, 5000, and 10,000 644197-03-00-01 212741-36-00-01 644573-03-00-01 645077-36-00-01 13-5/8 15,000 644196-01-00-01 212741-36-00-01 644898-02-00-01 645077-36-00-01

Inserted Packer Sizes and Part Numbers

BOP Size Pipe Size Packer Assembly

Part Number Insert Part Number Modified Packer Part Number 7-1/16” 15,000 psi WP 2-3/8” 2010833-04 2010771-04 2010813-04 7-1/16” 15,000 psi WP 2-7/8” 2010833-05 2010771-05 2010813-05 7-1/16” 15,000 psi WP 3-1/2” 2010833-06 2010771-06 2010813-06 7-1/16” 15,000 psi WP 4-1/2” 2010833-07 2010771-07 2010813-07 11” 10,000 psi WP 2-3/8” 2010952-01 2010938-01 2010937-01 11” 10,000 psi WP 2-7/8” 2010952-02 2010938-02 2010937-02 11” 10,000 psi WP 3-1/2” 2010952-03 2010938-03 2010937-03 11” 10,000 psi WP 4-1/2” 2010952-04 2010938-04 2010937-04 11” 10,000 psi WP 5” 2010952-05 2010938-05 2010937-05

(34)

UM BOP Operation and Maintenance

(T-275, 7-02)

I. Physical Data

A. Lubricants

1. Ram lubricant, P/N 705725 (CHEMLOA #681 BOP oil) or a water resistant non petroleum base grease.

2. Thread lubricant - which meets the requirements of the latest revision of API Bulletin 5A or Moly #503, (P/N 705444, 4 lb can)

3. Multi-purpose lubricant or grease.

4. Multi-purpose lubricant or grease for cold weather operation. 5. Hydraulic operating system:

a. Storage - P/N 718100 (Marston Bentley Preservation Fluid.)

b. Standard operation - Use a fresh water lubricant that forms a true solu-tion rather than an emulsion when mixed with water and/or antifreeze. 6. Seals and sealing surfaces - Hydraulic Oil (10-15 wt) P/N 203497.

B. Dimensional Drawings

1. SD-034559, Single UM BOP. 2. SD-034560, Double UM BOP.

3. SD-034566, Single UM BOP with Tandem Boosters

C. Drawings with Bills of Material

1. SD-034510, Single UM BOP, 7-1/16”. 2. SD-034498, Single UM BOP, 11”. 3. SD-034538, Single UM BOP, 13-5/8” 4. SD-034536, Tandem Booster Assembly. 5. SD-017508, Pipe Ram.

(35)

8. SD-10315, Flexpacker.

9. SD-017514, CAMRAM™ 350 Packer and Top Seal

D. Weights

Refer to pages 7, 9 and 11.

E. Lifting and Handling

1. Lift BOP assemblies only with slings appropriately rated for the maximun weight of the BOP.

2. Lift ram assemblies by installing a lifting eye, P/N 011849, in the threaded preparation in the ram.

3. Handle all other subassemblies using appropriately rated slings.

F. External Thread Connections

Description Size Location

Open Port 1” NPT BOP Body, Right Side

Close Port 1” NPT BOP Body, Left Side

G. Hydraulic Operating System Requirements

1. Use a fresh water lubricant in the hydraulic system that forms a true solution rather than an emulsion when mixed with water and/or antifreeze.

2. Refer to page 21 for fluid requirements.

3. Normal pressure for the hydraulic operating system is 1500 psi (103 Bars). 4. Maximum pressure to shear drill pipe is 2800 psi (193 Bars).

5. The maximum hydraulic operating pressure limit is 3000 psi (207 Bars) to op-erate rams.

(36)

H. API 16A Drift Diameter

Size and Working Presure API Drift 7-1/16” 3000 psi 7.032” (179 mm) 7-1/16” 5000 psi 7.032” (179 mm) 7-1/16” 10,000 & 15,000 psi 7.032” (179 mm) 11” 3000, 5000 & 10,000 psi 10.970” (279 mm) 11” 15,000 psi 10.970” (279 mm) 13-5/8” 3000 & 5000 psi 13.595” (345 mm) 13-5/8” 10,000 psi 13.595” (345 mm) 13-5/8” 15,000 psi 13.595” (345 mm)

II. Applicable Operating Characteristics

A. Subasemblies

1. Pipe ram operating characteristics. a. Seals around drill pipe or casing. 2. Flexpacker rams.

a. Seals and holds low or high pressure on drill pipe. b. It is not recommended to hang off on Flexpacker rams. 3. Shear rams

a. Shearing capabilities are dependent upon the size and working pressure of the BOP and the shearing configuration associated with that BOP. 4. Bonnet

a. Houses the BOP hydraulic operating system. b. Provides access to the rams.

(37)

III. Disassembly Procedure

A. Part Preparation Prior To Disassembly

The work area should be clean and well lighted.

B. BOP Disassembly

Reference pages 12, 14 and 16.

1. Use an air wrench to break and unscrew the bonnet bolts (Item 50) on both sides of the BOP.

2. Apply hydraulic closing pressure to the rams CLOSE connection on the BOP to open the bonnet assembly.

3. Screw the lifting eye (Item 40) into the top of the ram.

4. Use a hoist to lift up on the ram to remove it from the operating piston rod. 5. Remove the seal (Item 51) that resides in the seal bore of the BOP body. 6. With a spanner wrench and a hammer, break loose the locking screw

hous-ing nuts. (Item 39).

7. Remove the nuts, the locking screw housing (Item 22), and the locking screw (Item 20).

8. Remove the locking screw housing studs (Item 38) with a small pipe wrench. 9. From the bonnet, remove the plastic packing screw (Item 13), set screw (Item

12) and packing.

10. Unscrew the plastic packing check valve (Item 11). 11. Remove the bonnet bolts from the bonnet asembly.

12. Insert the lifting eye (Item 38) into the intermediate flange or into the bon-net.

13. Attach a hoisting cable to the lifting eye and apply tension to the cable to hold up the bonnet asembly.

14. Using a crescent wrench, loosen the ram change pistons (Item 4) and (Item 5) on the flats provided.

15. Once the ram change pistons are completely loose, move the assembly to the side away from the main body of the BOP.

(38)

C. Bonnet Disassembly

1. 7-1/16” UM BOP Bonnet Disassembly Reference page 12.

a. Remove the lock screw housing nuts (Item 39) and detach the lock screw housing assembly (Items 22 and 20) from the bonnet.

b. Remove the cylinder housing nuts (Item 26) and remove the cylinder head (Item 24) from the bonnet assembly.

c. Remove the ram change pistons (Items 4 and 5). d. Remove the ram change cylinders (Item 6). e. Remove the piston subassembly (Item 3).

f. Remove the operating cylinder studs (Item 25). g. Remove the operating cylinder (Item 23). h. Inspect all seals and replace as necessary. 2. 11” UM BOP Bonnet Disassembly

Reference page 14.

a. Remove the nuts (Item 37) and detach the lock screw housing assembly (Items 37 and 20) from the bonnet.

b. Remove the cylinder housing nuts (Item 26) and remove the cylinder head (Item 24) from the bonnet assembly.

f. Remove the operating cylinder studs (Item 25). g. Remove the operating cylinder (Item 23). h. Inspect all seals and replace as necessary. 3. 13-5/8” UM BOP Bonnet Disassembly

Reference page 16.

a. Detach the lock screw housing subassembly from the bonnet assembly with the 12 point (ferry head) cap screws. (Item 39).

(39)

24).

f. Remove the operating cylinder studs (Item 25). g. Remove the operating cylinder (Item 23). h. Inspect all seals and replace as necessary.

IV. Assembly Procedure

A. Part Preparation Prior to Assembly

The work area should be clean and well lighted.

1. Remove all dirt, grit, oil, and contaminates from the ram bore, ram change piston holes, bonnet stud holes, all fluid passageways in the body, and inter-mediate flange. Clean water and detergent should be used for cleaning. High pressure air may also be used if it is dry air.

2. Clean all internal surfaces of bonnets using clean water and detergent. Lubri-cate internal sealing surfaces.

3. Clean pistons, cylinders, and intermediate flanges, using clean water and de-tergent. Lubricate areas that will come in contact with other parts.

4. Lubricate sealing surfaces behind the threads in the bonnet stud holes in the BOP body after cleaning this area.

5. Sealed elastomer containers should not be opened until they are required for assembly. This is to prevent contamination and damage to the seal.

B. Bonnet Assembly

1. 7-1/16” UM BOP Bonnet Assembly Reference page 12.

a. Install the lip seal (Item 16), lip seal retainer (Item 18), retaining rings (Item 19), ring gaskets (Item 21), energizing ring (Item 15), plastic packing retainer ring (Item 14), and O-rings (Item 17) into the bonnet (Item 2). b. Lay down the bonnet (Item 2) with the cylinder side up, situated on blocks

or a pallet of sufficient height to allow the ram shaft and ram change pis-tons to extend past the body face at least six inches.

(40)

c. Install the cylinder studs (Item 25) onto the bonnet (Item 2).

d. Install the O-rings (Item 31) onto the operating cylinder (Item 23), then in-stall the operating cylinder (Item 23) onto the bonnet (Item 2).

e. Install the concentric booster ring (Item 42), split retainer ring (Item 41), seal rings (Item 30) and O-ring (Item 31) onto the piston subassembly (Item 3) and then install the piston subassembly (Item 3) into the bonnet. Note: This piston can be installed in two positions, depending on whether the order is for

shear rams or pipe rams. The piston is shown in the shear position in SD-034510. Reverse the piston position for standard pipe ram use.

f. Install the O-rings (Item 35) onto the ram change cylinders (Item 6) and then install the ram change cylinders onto the bonnet (Item 2).

Note: It is highly recommended that the ram change pistons be installed one time in the

preventer body prior to installation in the bonnet. This is to ensure that all threads are formed correctly and no debris is left in the threads that will make subsequent bonnet installation difficult.

g. Install the O-rings (Item 35), wear ring (Item 34), and seal ring (Item 33) onto the ram change pistons (Items 4 and 5). On some versions there are two O-ring grooves near the threaded end. O-rings should be installed in both grooves. Install the ram change pistons into the ram change cylin-ders (Item 6). The bonnet may be assembled as either a left or right hand bonnet. The left-hand configuration is shown in SD-034510. Reverse the location of the open and close pistons for a right-hand bonnet assembly. h. Install the seal ring (Item 27) and retaining rings (Items 28 and 29) onto

the cylinder head (Item 24) and install this subassembly on the assembled bonnet components. Install the nuts (Item 26) onto the cylinder studs (Item 25). Torque the nuts (Item 26) per Cameron Engineering Bulletin EB701D.

i. Install the locking screw (Item 20) into the lock screw housing (Item 22). Note: The lock screw must be installed in the fully extended position.

j. Install the studs (Item 38) on the cylinder head (Item 24).

k. Attach the lock screw housing subassembly to the bonnet assembly and install the nuts (Item 39). The housing should be oriented so that one of the three support ribs is aligned with the top of the bonnet. This is to help deflect falling objects from the lock screw and tail rod. Torque to the value listed in Cameron Engineering Bulletin EB701D.

l. Install the check valve (Item 11), plastic packing (Item 44), socket head set screw (Item 12) and pipe plug (Item 13).

(41)

n. Lift the bonnet assembly and set it down with the piston in the horizontal position. Install the ram guides (Item 10) into the bonnet. Using a small pipe wrench or strap wrench tighten these until they bottom out in the bonnet.

o. Insert the bonnet bolts (Item 50) into the bonnet (Item 2). 2. 11” UM BOP Bonnet Assembly

Reference page 14.

a. Install the lip seal (Item 16), lip seal retainer (Item 18), retaining rings

(Item 19), ring gasket (Item 43), energizing ring (Item 15), and O-rings (Items 14 and 17) into the bonnet (Item 2).

b. Lay down the bonnet (Item 2) with the cylinder side up, situated on blocks or a pallet of sufficient height to allow the ram shaft and ram change pis-tons to extend past the body face at least six inches.

c. Install the cylinder studs (Item 25) onto the bonnet (Item 2).

d. Install the blind plug (Item 40), pipe plug (Item 41), and tubing gland (Item 42) onto the bonnet (Item 2).

e. Install the O-rings (Item 21) onto the operating cylinder (Item 23), then in-stall the operating cylinder (Item 23) onto the bonnet (Item 2).

f. Install the seal ring (Item 30) and wear ring (Item 31) onto the piston sub-assembly (Item 3) and then install the piston subsub-assembly (Item 3) into the bonnet.

Note: This piston can be installed in two positions, depending on whether the order is for

g. Install the O-rings (Item 33) onto the ram change cylinders (Item 6) and then install the ram change cylinders onto the bonnet (Item 2).

h. Install the O-rings (Items 28 and 35) and wear ring (Item 32) onto the ram change pistons (Items 4 and 5). On some versions there are two O-ring grooves near the threaded end. O-rings should be installed in both grooves. Install the ram change pistons into the ram change cylinders (Item 6). The bonnet may be assembled as either a left or right hand

(42)

bon-net. The left-hand configuration is shown in SD-034498. Reverse the loca-tion of the open and close pistons for a right-hand bonnet assembly. i. Install the O-rings (Item 17) onto the cylinder head (Item 24) and install

this subassembly on the assembled bonnet components. Install the nuts (Item 26) onto the cylinder studs (Item 25). Torque the nuts (Item 26) per Cameron Engineering Bulletin EB701D.

j. Install the locking screw (Item 20) into the lock screw housing (Item 22). Note: The lock screw must be installed in the fully extended position.

k. Install the studs (Item 36) on the cylinder head (Item 24).

l. Attach the lock screw housing subassembly to the bonnet assembly and install the nuts (Item 37). The housing should be oriented so that one of the three support ribs is aligned with the top of the bonnet. This is to help deflect falling objects from the lock screw and tail rod. Torque to the value listed in Cameron Engineering Bulletin EB701D.

m. Install the check valve (Item 11), plastic packing (Item 29), socket head set screw (Item 12) and pipe plug (Item 13).

n. Install the lifting eye (Item 78) onto the bonnet (Item 2).

o. Lift the bonnet assembly and set it down with the piston in the horizontal position. Install the ram guides (Item 10) into the bonnet. Using a small pipe wrench or strap wrench tighten these until they bottom out in the bonnet.

p. Insert the bonnet bolts (Item 52) with the O-rings (Item 74) into the bon-net (Item 2).

3. 13-5/8” UM BOP Assembly Reference page 16.

a. Install the polypaks (Item 14), retainers (Item 12), retaining rings (Item 11), energizing ring (Item 28) and plastic packing ring (Item 27) into the bon-net (Item 2) as shown in Detail A of SD-034538.

b. Install the O-rings (Item 38) and wear ring (Item 15) into the bonnet (Item 2).

c. Lay down the bonnet (Item 2) with the cylinder side up, situated on blocks or a pallet of sufficient height to allow the ram shaft and ram change pis-tons to extend past the body face at least six inches.

(43)

Note: Be sure to install the studs with end stamped ‘3A Bonnet End’ into the bonnet. The

end marked ‘2A’ is for the nuts. This assists in having the nuts being capable of be-ing loosened without causbe-ing the studs to unthread from the bonnet.

e. Install the O-rings (Item 31) onto the operating cylinder (Item 23), then in-stall the operating cylinder (Item 23) onto the bonnet (Item 2).

f. Install the seal ring (Item 30) and wear ring (Item 29) onto the piston sub-assembly (Item 3) and then install the piston subsub-assembly (Item 3) into the bonnet.

Note: This piston can be installed in two positions, depending on whether the order is for

g. Install the O-rings (Item 36) onto the ram change cylinders (Item 6) and then install the ram change cylinders onto the bonnet (Item 2).

h. Install the O-rings (Items 35 and 37) onto the ram change pistons (Items 4 and 5). On some versions there are two O-ring grooves near the threaded end. O-rings should be installed in both grooves. Install the ram change pistons into the ram change cylinders (Item 6). The bonnet may be assem-bled as either a left or right hand bonnet. The left-hand configuration is shown in SD-034538. Reverse the location of the open and close pistons for a right-hand bonnet assembly.

i. Install the polypaks (Item 14), retainers (Item 12), and retaining rings (Item 11), as shown in Detail A of SD-034538 onto the cylinder head (Item 24) and install this subassembly on the assembled bonnet components. In-stall the washers (Item 32) and nuts (Item 26) onto the cylinder studs (Item 25). Torque the nuts (Item 26) per Cameron Engineering Bulletin EB701D. j. Install the O-rings (Item 8) onto the ram change piston caps (Item 9) and

assemble onto the cylinder head (Item 24). There is no specific torque re-quirement as these make up solid into the cylinder head. Use PN

2164429-01 spanner wrench to make up the caps into the cylinder head. k. Install the locking screw (Item 20) into the lock screw housing (Item 22). Note: The lock screw must be installed in the fully extended position.

l. Attach the lock screw housing subassembly to the bonnet assembly with the 12 point (ferry head) cap screws (Item 39). The housing should be ori-ented so that one of the three support ribs is aligned with the top of the

(44)

bonnet. This is to help deflect falling objects from the lock screw and tail rod. Torque to the value listed in Cameron Engineering Bulletin EB701D. m. Install the check valve (Item 16), plastic packing (Item 19), socket head set

screw (Item 17) and pipe plug (Item 18).

n. Install the pipe plugs (Item 45) onto the ram change piston caps (Item 9). o. Install the Autoclave tubing nut and gland (Item 42) with the blind plug

(Item 41) onto the bonnet (Item 2) and cylinder head (Item 24).

p. Install the hex socket pipe plugs (Item 43) onto the bonnet (Item 2) and cylinder head (Item 24).

q. Install the lifting eyes (Item 40) onto the bonnet (Item 2).

r. Lift the bonnet assembly and set it down with the piston in the horizontal position. Install the ram guides (Item 10) into the bonnet. Using a small pipe wrench or strap wrench tighten these until they bottom out in the bonnet.

s. Insert the bonnet bolts (Item 50) with the washers (Item 33) and O-rings (Item 51) into the bonnet (Item 2).

V. Operation and Installation Procedures

A. Preparation

Prior to the installation of the preventer, ensure that the following requirements are met:

1. The capacity and the pressure rating of the accumulators and the pressure pumps must comply with the API RP53 recommendations or appropriate reg-ulatory agency requirements.

2. Ensure that the ring gaskets are correct for the preventer flange, the hub size, and the pressure rating.

B. Installation

1. Install the preventer, ensuring that the preventer is right-side-up (outlets are below the center of the preventer).

2. Inspect the preventer, the ram subassemblies, and all rubber parts during in-stallation.

3. Remove the external mechanical protectors.

(45)

6. Drain the fluid from the operating system.

7. Remove the 1” ball valves or pipe plugs from the inlet and outlet connec-tions.

8. Connect the hydraulic control lines, and flush the operating system with clean fluid.

9. Test for leaks in the operating system (refer to Part VII, TESTING.)

10. Install the rams in accordance with the assembly procedure described in Part IV, ASSEMBLY.

11. While installing the rams, inspect the ram bore and bonnet. a. Inspect the vertical bore for key seating.

b. Inspect the intersection between the vertical bore and the ram bore. Grind out any raised metal surfaces. Do not remove any metal below the original surface.

VI. Maintenance Procedures

A. Routine Maintenance

1. If more than 500 psi (34.5 Bars) hydraulic pressure is required to operate the ram subassemblies when there is no pressure in the well bore, determine the cause and correct any irregularities.

Caution: To avoid damage to the packers, close pipe and variable bore rams only when

pipe is in the preventer.

2. Pressure test and operate the preventer once a week per API RP53 “Periodic Field Testing” or appropriate regulatory agency requirement.

B. Periodic Maintenance

1. Once a year, or every six months in cold weather conditions, completely dis-assemble the preventer.

Note: For detailed description of disassembly, see Part III, DISASSEMBLY. a. Clean all parts. Do not use a wire brush on sealing areas. b. Replace all rubber seals, gaskets, and O-rings.

(46)

d. Repair or replace damaged metal parts. 2. Reassemble the preventer.

Note: For a detailed description of assembly, see Part IV, ASSEMBLY.

a. After reassembling the preventer, test the rams and operating system. Re-fer to Part VII, TESTING for the correct procedure.

VII. Testing

A. Hydraulic Operating System

1. Test the hydraulic operating system after installation.

a. Flush the hydraulic operating system with clean operating fluid. b. Test for proper stroking of the rams and operating system.

1) Apply a maximum of 300 psi (20.7 Bars) hydraulic pressure to the OPEN port.

2) Ensure that the rams open.

3) Reduce hydraulic pressure to zero psi.

4) Apply a maximum of 300 psi (20.7 Bars) hydraulic pressure to the CLOSE port.

5) Ensure the rams close.

6) Reduce hydraulic pressure to zero psi. c. Test for leaks in the operating system.

1) Remove the hydraulic line from the OPEN port.

Note: If testing pipe, casing, flex packers, or variable bore rams, be sure that an

appropri-ate size test mandrel is installed into the preventer. DO NOT close the rams on an open hole unless closing pressure is less than 300 psi (20.7 Bars). Flex Packers and VBRs should be tested with the largest pipe size for that packer.

2) Apply 300 psi (20.7 Bars) hydraulic pressure to the CLOSE port, and ob-serve the OPEN port for leaks.

3) Increase the pressure to 3000 psi (207 Bars) and observe the OPEN port for leaks.

4) Inspect for leaks between the intermediate flange, the bonnet, and the BOP body. Bleed all pressure from the BOP closing line.

(47)

6) Remove the hydraulic line from the CLOSE port.

7) Apply 300 psi (20.7 Bars) hydraulic pressure to the OPEN port, and ob-serve the CLOSE port for leaks.

8) Increase the pressure to 3000 psi (207 Bars) and observe the CLOSE port for leaks.

9) Inspect for leaks between the intermediate flange, body, and bonnet. Bleed all pressure from the BOP opening line.

10) Replace the hydraulic line to the CLOSE port.

11) Replace the seals if leaks were observed and repeat the test with new seals.

12) Repeat the procedure for each preventer.

B. Ram Test

(After installation and as required by API RP53 or appropriate regulatory agency.)

1. Hydraulically test ram packers with water using the following procedure: a. Install the BOP stack on a prepared test stump or install a test plug below

the BOP if on the wellhead.

b. Inspect for ram packer leaks at low pressure by closing rams on an appro-priate size test mandrel (none if blinds or shears are used) with 1500 psi (103 Bars) operating pressure, and apply 200 psi (13.8 Bars) pressure under the rams. Hold pressure for 3 minutes. Maximum pressure drop is 10 psi (.7 Bars) in 3 minutes.

c. Increase pressure slowly to the rated working pressure of the preventer. Hold pressure for 3 minutes. Maximum pressure drop is 100 psi (6.9 Bars) in 3 minutes.

d. If rams leak at low pressure or at working pressure, inspect for worn ram packers and replace if necessary.

e. Repeat the above procedure for each set of casing, pipe and shear rams.

Cameron Um Bop Ram

UM Blowout Preventer

Operation and Maintenance Manual

PREFACE

Contents

Tandem Booster Assembly

Tandem Boosters for UM BOPs

UM BOP Specifications and Accessories

UM BOP Ram Hang-Off Weights and

Shear Requirements

Hang-Off Weights

Drill Pipe Shearing Requirements

U and UM BOP Pipe Rams

U and UM BOP Pipe Ram Part Numbers

U and UM BOP Pipe Ram Part Numbers

-U and -UM BOP Pipe Ram Part Numbers

U and UM BOP Shearing Blind Rams

U and UM BOP H

2

S Shearing Blind Ram Part Numbers

U and UM BOP Shearing Blind Ram Part Numbers

Flexpackers for U and UM BOPs

CAMRAM 350 Packers and Top Seals for

U and UM BOPs

Bonnet Seals and Connecting Rod Seals

UM BOP Operation and Maintenance

I. Physical Data

A. Lubricants

B. Dimensional Drawings

C. Drawings with Bills of Material

D. Weights

E. Lifting and Handling

F. External Thread Connections

G. Hydraulic Operating System Requirements

H. API 16A Drift Diameter

II. Applicable Operating Characteristics

A. Subasemblies

III. Disassembly Procedure

A. Part Preparation Prior To Disassembly

B. BOP Disassembly

C. Bonnet Disassembly

IV. Assembly Procedure

A. Part Preparation Prior to Assembly

B. Bonnet Assembly

V.

Operation and Installation Procedures

A. Preparation

B. Installation

VI. Maintenance Procedures

A. Routine Maintenance

B. Periodic Maintenance

VII. Testing

A. Hydraulic Operating System

B. Ram Test

VIII. Storage

A. Preventer