○
○Speed CPUSpeed CPU [[ Mea Meaningning]]
[[ExplanationExplanation]]
[[CountermeasuresCountermeasures]]
T
TC
CD 1
D 10
07
7
S
SD
D1
1U O
U ON t
N trro
ou
ub
blle
e
SD1U does not operate from bottom floor. SD1U does not operate from bottom floor.
It is detected when SD1U input does not enter when car is
It is detected when SD1U input does not enter when car is in top floor.in top floor.
1.Check the value of address 8021 from MEMORY READ MODE, 1.Check the value of address 8021 from MEMORY READ MODE,
when car is not in top floor. If it is x00, it is normal. If it is x01, when car is not in top floor. If it is x00, it is normal. If it is x01, check voltage of LSU-05, LSU-06 and HA-06. They must have check voltage of LSU-05, LSU-06 and HA-06. They must have DC 48V.
DC 48V.
DC48V is abnormal, check wiring and connection. DC48V is abnormal, check wiring and connection.
2. Check the value of address 8023 from MEMORY READ MODE 2. Check the value of address 8023 from MEMORY READ MODE when car is in top floor. If it is x01, it is normal. If it is x01, check when car is in top floor. If it is x01, it is normal. If it is x01, check voltage of LSU-06 and HA-06, and They must have DC 0V. voltage of LSU-06 and HA-06, and They must have DC 0V. 3. Check if SD switch
3. Check if SD switch works normally.works normally. 4. Check assembly condition of SDS1U. 4. Check assembly condition of SDS1U.
TCD 107 TCD 107 check_out
check_out SWD_I[VI_SD1U]SWD_I[VI_SD1U] FTD_Current_Fl == FTD_Current_Fl == SPD_Floor_Spec.Top SPD_Floor_Spec.Top 0x8021 0x8021 TCD 77 TCD 77 check_out check_out 0x923C 0x923C ERD_Digi_Fl_Err ERD_Digi_Fl_Err Coil[AC_OP_FHM_ Coil[AC_OP_FHM_ START_MODE] START_MODE] Coil[AC_OP_ Coil[AC_OP_ FHM_MODE] FHM_MODE] Coil[SW_SS_48V_ Coil[SW_SS_48V_ DOWN_HOLD] DOWN_HOLD] Coil[SW_GS_ Coil[SW_GS_ OPEN_ZONE]
OPEN_ZONE] SWD_I[VI_LDC]SWD_I[VI_LDC] TCD 78 TCD 78 TCD 114TCD 114 0x9031 0x9031 0x90320x9032 0 0xx99225566 00xx88002255 Coil[SV_ Coil[SV_ FORCE_DECEL] FORCE_DECEL] 0x921D 0x921D Coil[IS_ZERO_V] Coil[IS_ZERO_V] Coil[AC_OP_MAINT_MODE] Coil[AC_OP_MAINT_MODE] 0x91F2 0x91F2 0x9030 0x9030
○
○Speed CPUSpeed CPU [[ Mea Meaningning]]
[[ExplanationExplanation]]
[[CountermeasuresCountermeasures]]
T
TC
CD 1
D 10
08
8
S
SD
D2
2U O
U ON t
N trro
ou
ub
blle
e
Detected only when the rated speed is 90m/min or more. Detected only when the rated speed is 90m/min or more.
Detected when SD2U input does not enter when car is on the top floor. Detected when SD2U input does not enter when car is on the top floor.
SD2U does not operate from bottom floor. SD2U does not operate from bottom floor.
1.Check the value of address 8022 from MEMORY READ 1.Check the value of address 8022 from MEMORY READ
MODE, when car is not in bottom floor. If it is x00, it is normal. MODE, when car is not in bottom floor. If it is x00, it is normal. If it is x01,
If it is x01, check voltage of LSU-07, LSU-08 and HA-07. Theycheck voltage of LSU-07, LSU-08 and HA-07. They must have DC 48V.
must have DC 48V.
DC48V is abnormal, check wiring and connection. DC48V is abnormal, check wiring and connection. 2. Check the value of address 8022 from MEMORY READ 2. Check the value of address 8022 from MEMORY READ
MODE when car is in bottom floor. If it is x01, it is normal. If it MODE when car is in bottom floor. If it is x01, it is normal. If it is x01, check voltage of LSU-08 and HA-07, and They must is x01, check voltage of LSU-08 and HA-07, and They must have DC 0V.
have DC 0V. 3. Check if SD switch
3. Check if SD switch works normally.works normally. 4. Check assembly condition of SDS2U. 4. Check assembly condition of SDS2U.
TCD 108 TCD 108 c
chheecckk__oouutt SWSWDD__II[[VVII__SSDD22UU]] FTD_Current_Fl == FTD_Current_Fl == SPD_Floor_Spec.Top SPD_Floor_Spec.Top 0x8022 0x8022 SPD_Control_Spec. SPD_Control_Spec. Contract_Velocity >= 90 Contract_Velocity >= 90 TCD 77 TCD 77 check_out check_out 0x923C 0x923C ERD_Digi_Fl_Err ERD_Digi_Fl_Err Coil[AC_OP_FHM_ Coil[AC_OP_FHM_ START_MODE] START_MODE] Coil[AC_OP_ Coil[AC_OP_ FHM_MODE] FHM_MODE] Coil[SW_SS_48V_ Coil[SW_SS_48V_ DOWN_HOLD] DOWN_HOLD] Coil[SW_GS_ Coil[SW_GS_ OPEN_ZONE]
OPEN_ZONE] SWD_I[VI_LDC]SWD_I[VI_LDC] TCD 78 TCD 78 TCD 114TCD 114 0x9031 0x9031 0x90320x9032 0 0xx99225566 00xx88002255 Coil[SV_ Coil[SV_ FORCE_DECEL] FORCE_DECEL] 0x921D 0x921D Coil[IS_ZERO_V] Coil[IS_ZERO_V] Coil[AC_OP_MAINT_MODE] Coil[AC_OP_MAINT_MODE] 0x91F2 0x91F2 0x9030 0x9030
○
○Speed CPUSpeed CPU [[ Mea Meaningning]]
[[ExplanationExplanation]]
[[CountermeasuresCountermeasures]]
TC
TCD
D 1
114
14
R
RPD
PD O
ON
N tr
tro
oub
uble
le (L
(LD
DC
C))
Detected RPD (LDC) ON/OFF trouble. Detected RPD (LDC) ON/OFF trouble.
1.Check at door zone, if the value of 3rd row and 5th c
1.Check at door zone, if the value of 3rd row and 5th c olumn of olumn of
DOA-DOA-100 is ‘1’.100 is ‘1’.
2. Check at no door zone, if the value of 3rd row
2. Check at no door zone, if the value of 3rd row and 5th columnand 5th column of
DOA-of DOA-100 is ‘0’.100 is ‘0’.
3. Check the voltage between Y1-05 of DOM PCB and CA-10 of 3. Check the voltage between Y1-05 of DOM PCB and CA-10 of
DOC-131. (with door zone, 0V is normal and without door zone, DOC-131. (with door zone, 0V is normal and without door zone, 48V is normal)
48V is normal)
4. Check if RPD is defective. 4. Check if RPD is defective.
Coil[RS_RUNNING]
Coil[RS_RUNNING] SWD_I[VI_LDC]SWD_I[VI_LDC]
Coil[SW_GS_LDC] Coil[SW_GS_LDC]
Co
Coilil[S[SW_GW_GS_S_OPOPENEN_Z_ZONONE]E] CoCoil[il[ISIS_C_CURUR_V_V_1_10]0]
TMC_Check(RPD_OFF_ TMC_Check(RPD_OFF_ ERR_T,FINISH_STATE) ERR_T,FINISH_STATE) Coil[SW_FS_MAINT] Coil[SW_FS_MAINT] check_out check_out TCD 114 TCD 114 TMC_Start(RPD_ TMC_Start(RPD_ OFF_ERR_T) OFF_ERR_T) check_out check_out 0x91B0 0x91B0 0x929A0x929A 0x80250x8025 0x9256 0x9256 0x9251 0x9251 0x91EB 0x91EB T
TCCD D 7788 Coil[RS_RUNNING]Coil[RS_RUNNING] SWSWDD__II[[VVII__CC11SSTT]]
0x91B0 0x91B0
SWD_I[VI_C1BR] SWD_I[VI_C1BR]
Coil[S
Coil[SV_FASV_FAST_MOT_MODE]DE] Coil[ICoil[IS_CUS_CUR_V_R_V_10]10]
check_out check_out 0x9202 0x9202 0x91EB0x91EB 0x802A 0x802A 0x80290x8029 TMC_Check(RPD_ON_OFF_ TMC_Check(RPD_ON_OFF_ DETECT_T,FINISH_STATE) DETECT_T,FINISH_STATE) TCD 114TCD 114 TMC_Reset(RPD_ON_ TMC_Reset(RPD_ON_ OFF_DETECT_T) OFF_DETECT_T) check_out
check_out SWD_I[VI_LDC] == old_LDC_stateSWD_I[VI_LDC] == old_LDC_state
0x8025 0x8025 old_LDC_state old_LDC_state SWD_I[VI_LDC] SWD_I[VI_LDC] TMC_Start(RPD_ON_ TMC_Start(RPD_ON_ OFF_DETECT_T) OFF_DETECT_T) 2070 msec 2070 msec RPD off error RPD off error Coil[AC_OP_ALP_MODE] Coil[AC_OP_ALP_MODE] 0x9041 0x9041 RPD on error RPD on error
○
○Speed CPUSpeed CPU [[ Mea Meaninnin gg]]
[[ExplanationExplanation]]
[[ S S ymptomymptom]]
TC
TCD
D 1
116
16
R
RPD
PD O
ON
N tr
tro
oub
uble
le (L
(LD
DU
U))
[[CountermeasuresCountermeasures]] Detected RPD(LDU) ON/OFF trouble.
Detected RPD(LDU) ON/OFF trouble.
1. The trouble will be detected, when SPEC data in address 0016 1. The trouble will be detected, when SPEC data in address 0016 is set, even if rope compensation is not applied.
is set, even if rope compensation is not applied. 2. Check if the input signal of LDU is
2. Check if the input signal of LDU is activated normally.activated normally. (Check by Memory Read Mode A21E, Address: 8027) (Check by Memory Read Mode A21E, Address: 8027)
3. Check the voltage between Y3-14 of DOM PCB and CB-03 of 3. Check the voltage between Y3-14 of DOM PCB and CB-03 of
DOC-131. (B contact) DOC-131. (B contact) 48V: LDU off, 0V: LDU on. 48V: LDU off, 0V: LDU on.
4. Replace LDU, if LDU RPD is defective. 4. Replace LDU, if LDU RPD is defective. No problem for operation, but rope
No problem for operation, but rope compensation function iscompensation function is unable.
unable.
When LDU trouble is detected, rope compensation function would be cut. When LDU trouble is detected, rope compensation function would be cut.
SPD_Function. SPD_Function. Rope_Compen Rope_Compen Coil{AC_OP_ Coil{AC_OP_ MAINT_MODE] MAINT_MODE] SPD_I[SP_ SPD_I[SP_ FAC_INSPECT] FAC_INSPECT] TCD 114 TCD 114 Coil[IS_ZONE_250] Coil[IS_ZONE_250] TMC_Check(POWER_ TMC_Check(POWER_ READY_T,FINISH_STATE) READY_T,FINISH_STATE) check_out check_out 0x9030 0x9030 0x8025 0x8025 0x9191 0x9191 0x91F2 0x91F2 TCD 79 TCD 79 TCD 78 TCD 78 tmp tmp tmp tmp Coil[IS_ZERO_V]Coil[IS_ZERO_V] check_out check_out SWD_I[VI_LDC] SWD_I[VI_LDC] TCD 116 TCD 116 SWD_I[VI_LDU]
SWD_I[VI_LDU] SWD_I[VI_LDD]SWD_I[VI_LDD] 0x8028 0x8028 0x8027 0x8027 tmp tmp check_out check_out Coil[IS_ZONE_250]
Coil[IS_ZONE_250] SWD_I[VI_LDC]SWD_I[VI_LDC] 0x8025 0x8025 0x9191 0x9191 check_out check_out TCD 116 TCD 116 SWD_I[VI_LDU]
SWD_I[VI_LDU] SWD_I[VI_LDD]SWD_I[VI_LDD] 0x8028 0x8028 0x8027 0x8027 ldc_on_event ldc_on_event SWD_I[VI_LDU] ^ old_ldc
SWD_I[VI_LDU] ^ old_ldc SWD_I[VI_LDC]SWD_I[VI_LDC]
tmp tmp
Coil[IS_ Coil[IS_ ZONE_250]
ZONE_250] Coil[IS_ Coil[IS_ CUR_V_30]CUR_V_30] ldc_on_eventldc_on_event
TCD 116 TCD 116 Coil[RS_
Coil[RS_ UP_RUN]
UP_RUN] SWD_I[VI_LDU]SWD_I[VI_LDU]
ldc_off_event ldc_off_event
TCD 116 TCD 116 Coil[RS_UP_RUN]
Coil[RS_UP_RUN] SWD_I[VI_LDU]SWD_I[VI_LDU]
SWD_I[VI_LDC] SWD_I[VI_LDC] old_ldc old_ldc 0x8027 0x8027 0x8027 0x8027 0x91AE 0x91AE 0x9191 0x9191 0x91EE0x91EE
○
○Speed CPUSpeed CPU [[ Mea Meaninnin gg]]
[[ExplanationExplanation]]
[[ S S ymptomymptom]]
TC
TCD
D 1
117
17
R
RPD
PD O
ON
N tr
tro
oub
uble
le (L
(LD
DD
D))
[[CountermeasuresCountermeasures]] Detected RPD (LDD) ON/OFF trouble.
Detected RPD (LDD) ON/OFF trouble.
1.The trouble will be detected, when
1.The trouble will be detected, when SPEC data in address 0016SPEC data in address 0016 is set, even if rope compensation is not applied.
is set, even if rope compensation is not applied. 2. Check if the input signal of LDD is
2. Check if the input signal of LDD is activated normally.activated normally. (Check by Memory Read Mode A21E, Address: 8028) (Check by Memory Read Mode A21E, Address: 8028)
3. Check the voltage between Y3-15 of DOM PCB and CB-04 of 3. Check the voltage between Y3-15 of DOM PCB and CB-04 of
DOC-131. (B contact) DOC-131. (B contact) 48V: LDD off, 0V: LDD on. 48V: LDD off, 0V: LDD on. 4. Replace LDD, if LDD RPD is defective. 4. Replace LDD, if LDD RPD is defective. No problem for operation, but rope
No problem for operation, but rope compensation function iscompensation function is unable.
unable.
When LDD trouble is detected, rope compensation function would be cut. When LDD trouble is detected, rope compensation function would be cut.
SPD_Function. SPD_Function. Rope_Compen Rope_Compen Coil{AC_OP_ Coil{AC_OP_ MAINT_MODE] MAINT_MODE] SPD_I[SP_ SPD_I[SP_ FAC_INSPECT] FAC_INSPECT] TCD 114 TCD 114 Coil[IS_ZONE_250] Coil[IS_ZONE_250] TMC_Check(POWER_ TMC_Check(POWER_ READY_T,FINISH_STATE) READY_T,FINISH_STATE) check_out check_out 0x9030 0x9030 0x8025 0x8025 0x9191 0x9191 0x91F2 0x91F2 TCD 79 TCD 79 TCD 78 TCD 78 tmp tmp tmp tmp Coil[IS_ZERO_V]Coil[IS_ZERO_V] check_out check_out SWD_I[VI_LDC] SWD_I[VI_LDC] TCD 117 TCD 117 SWD_I[VI_LDU]
SWD_I[VI_LDU] SWD_I[VI_LDD]SWD_I[VI_LDD] 0x8028 0x8028 0x8027 0x8027 tmp tmp check_out check_out Coil[IS_ZONE_250]
Coil[IS_ZONE_250] SWD_I[VI_LDC]SWD_I[VI_LDC] 0x8025 0x8025 0x9191 0x9191 check_out check_out TCD 117 TCD 117 SWD_I[VI_LDU]
SWD_I[VI_LDU] SWD_I[VI_LDD]SWD_I[VI_LDD] 0x8028 0x8028 0x8027 0x8027 ldc_on_event ldc_on_event SWD_I[VI_LDU] ^ old_ldc
SWD_I[VI_LDU] ^ old_ldc SWD_I[VI_LDC]SWD_I[VI_LDC]
ldc_off_event ldc_off_event tmp tmp Coil[IS_ Coil[IS_ ZONE_250]
ZONE_250] Coil[IS_ Coil[IS_ CUR_V_30]CUR_V_30] ldc_on_eventldc_on_event
TCD 117 TCD 117 Coil[RS_
Coil[RS_ DOWN_RUN]
DOWN_RUN] SWD_I[VI_LDD]SWD_I[VI_LDD]
ldc_off_event ldc_off_event
TCD 117 TCD 117 Coil[RS_DOWN_RUN]
Coil[RS_DOWN_RUN] SWD_I[VI_LDD]SWD_I[VI_LDD]
SWD_I[VI_LDC] SWD_I[VI_LDC] old_ldc old_ldc 0x8028 0x8028 0x91AF 0x91AF 0x9191 0x9191 0x91EE0x91EE
○
○Speed CPUSpeed CPU [[ Mea Meaningning]]
[[ExplanationExplanation]]
[[CountermeasuresCountermeasures]]
TC
TCD 1
D 119
19
SL
SLOW
OW D
DOW
OWN S
N S/W
/W tr
trou
oubl
ble
e
Detect Slow Down Switch OFF trouble Detect Slow Down Switch OFF trouble
ERD_SDS_Off_Error ERD_SDS_Off_Error TCD 119 TCD 119 Coil[SW_GS_IS_STOP] Coil[SW_GS_IS_STOP]
TCD 119 will occur when car is in stop. TCD 119 will occur when car is in stop. Condition of detecting ERD_SDS_Off_Error Condition of detecting ERD_SDS_Off_Error
1. In case forced slow down occurs 1. In case forced slow down occurs
2. Excluding top and bottom floor, SD1U, SD2U are activated during operation 2. Excluding top and bottom floor, SD1U, SD2U are activated during operation
for 540msec and more. for 540msec and more.
3. Excluding top and bottom floor, SD1D, SD2D are activated during operation 3. Excluding top and bottom floor, SD1D, SD2D are activated during operation
for 540msec and more. for 540msec and more.
4. Excluding top floor, SD1U is activated at door zone for 540ms
4. Excluding top floor, SD1U is activated at door zone for 540ms ec and more.ec and more. 5. Excluding bottom floor, SD1D is activated at door zone f
5. Excluding bottom floor, SD1D is activated at door zone f or 540msec andor 540msec and more.
more.
1. Check the connection of SDS. 1. Check the connection of SDS.
If normal (SDS closed), check below. If normal (SDS closed), check below.
LSD-06 (SDS1D) is to be 48V LSD-06 (SDS1D) is to be 48V LSD-08 (SDS2D) is to be 48V LSD-08 (SDS2D) is to be 48V LSU-06 (SDS1U) is to be 48V LSU-06 (SDS1U) is to be 48V LSU-08 (SDS2U) is to be 48V LSU-08 (SDS2U) is to be 48V 2. Check if SDS switch works
2. Check if SDS switch works normally.normally. 3. Check assembly condition of SDS. 3. Check assembly condition of SDS.
○
○Speed CPUSpeed CPU [[ Mea Meaningning]]
[[ExplanationExplanation]]
[[CountermeasuresCountermeasures]]
TC
TCD 1
D 123
23
Re
Rege
gene
nera
rati
tive
ve Re
Resi
sisto
stor T
r The
herm
rmal
al tro
troub
uble
le
Regenerative Resistor Thermal error. Regenerative Resistor Thermal error.
1. Check the Regenerative resistor (THB) wiring according to 1. Check the Regenerative resistor (THB) wiring according to
drawing drawing
2. Check if the FAN works
2. Check if the FAN works normally.normally. 3. Check the balancing rate of
3. Check the balancing rate of counter weight.counter weight.
Coil[SW_GS_POWER_READY] Coil[SW_GS_POWER_READY] TCD123 TCD123 SWD_I[VI_REGEN_R_THERMAL SWD_I[VI_REGEN_R_THERMAL
