Additive nanomanufacturing methods (square) compared with conventional
Respiratory Virus Detection in Immunocompromised Patients with FilmArray Respiratory Panel Compared to Conventional Methods
... both methods, underwent further verification testing at Idaho Technol- ogy using validated real-time singleplex PCR ...both methods were randomly selected from all samples which were negative by FilmArray ...
6
A New Technique Provides Faster Particle Size Analysis at a Lower Cost Compared to Conventional Methods
... Introduction Recently, PMI finished development of an automated method for determining the envelope surface area of powders from their gas permeability. The method is based on theoretical and experimental work from ...
5
Validity and acceptability of a laser fluorescence device compared to conventional methods for detection of proximal caries in primary teeth
... Other methods for caries detection and diagnosis ...been compared to other diagnostic methods in many studies (Deery et ...Both methods are subjective rather than ...
266
Location of the sensorimotor cortex: functional and conventional MR compared
... supplement conventional MR imaging for locating the rolandic cortex. METHODS: Parasagittal MR images acquired in conjunc- tion with functional MR images were ...by conventional parcellation ...
5
Novel Soil Strength Criterion Compared with Conventional Criteria
... In this study, the authors conducted true triaxial tests of 4 kinds of intact loesses un- der conditions of consolidation and drain. Tests were completed with the newly devel- oped true triaxial apparatus, with 70 mm × ...
16
Diagnosis of paediatric tuberculosis by cartridge based nucleic acid amplification test and its effectiveness as compared to the other conventional diagnostic methods
... the methods were 100%.Compared with microscopy, Xpert offered better sensitivity for the diagnosis of Tuberculosis in children though remained suboptimum to culture ...
7
Hybrid Manufacturing: Analysis of Integrating Additive and Subtractive Methods.
... Machinability is an important factor for the unit cost, since selection of machining parameters can vary based on the material (Aluminum, Ti-6-Al-4V), available cutting tools (High speed steel, coated carbides) and ...
204
Additive and multiplicative properties of scoring methods for preference aggregation
... To each ranking problem (N, A) ∈ R, we associate a results matrix R = A − A > = (r ij ) ∈ R n×n and a matches matrix M = A+A > = (m ij ) ∈ N n×n , where m ij is the number of the comparisons between X i and X j , whose ...
27
The incremental cost effectiveness of introducing PCR for early detection of E coli infections associated with acute diarrhea compared to conventional microbiological methods
... technique compared to CMM for EHEC/STEC detection 28 4 DISCUSSION AND CONCLUSION In this study an economic analysis was performed to evaluate the incremental cost- effectiveness of the PCR technique ...
39
A Comparative Analysis between Conventional Manufacturing and Additive Manufacturing of Ankle-Foot Orthosis
... CAM software, adjustments to the AFO are done easier compared to the CM method. Thus, it could also reduce the amount of wastes generated during the manufacture. In other words, the production of AFO using AM ...
8
The efficiency of the conventional physical treatment of the shoulder pain compared to conventional treatment plus the Mulligan’s joint mobilization technique and acupuncture
... METHODS Patients We included a total of 277 consecutive patients from two institutions, from January 2013 to December 2016. Shoulder pain was diagnosed by the physi- cal medicine specialist based on medical ...
6
Abstract: The contact, residual, and ingestion efficacy of two conventional insecticides was compared with that of ano-
... Cáceres 2001; Barzman) . MATERIAL AND METHODS The experiments were conducted under laboratory conditions in 2017 and 2018 with adult P. oblongus collected by hand into plastic tubes within agro- chemically ...
7
Colon Capsule Endoscopy compared to Conventional Colonoscopy under routine screening conditions
... Methods: We performed a prospective, single-center pilot study at a University Hospital. Data were obtained from November 2007 until May 2008. Patients underwent CCE on Day 1 and CSPY on Day 2. Outcomes were ...
7
Superb microvascular imaging (SMI) compared with conventional ultrasound for evaluating thyroid nodules
... SMI is a relatively new imaging modality that is imple- mented on the Toshiba Aplio 500 ultrasound system. It enables better depiction of microvascularity and low- velocity blood flow compared with ...
6
nanomanufacturing technology?
... the nanomanufacturing technology industry and broadening of demand for emerging applica- tions such as solar, which are subject to many factors, including global economic conditions, business spending, consumer ...
10
NanoManufacturing and NanoRobots
... Nanomanufacturing is a key enabling technology for fulfilling the promise of nanotechnology with special material properties and processing capabilities at the nanoscale. Nanorobotics is an emerging ...
11
BIOS, conventional blocks compared
... thrips and western predatory mites), on the other hand, were significantly more abundant in BIOS blocks, though the difference was small. These findings contradict the broadly held assertion that mites can be reduced by ...
7
Additive Nanomanufacturing of Multifunctional Materials and Patterned Structures: A Novel Laser-Based Dry Printing Process
... This new method allows the in situ and on-demand formation of various nanoparticle building blocks in atmospheric pressure and at room temperature. These nanoparticle building blocks can be directed toward the substrate ...
10
Nanomanufacturing Process Database
... Nanomanufacturing processes are typically unique methods employed to control the shape, features, size, and morphology of materials in order to achieve some value-added functionality. Depending on the ...
5
Several Trends in Nanomanufacturing
... (molecules as devices “by design”, nanoscale machines, etc.), - hierarchical integration with larger scale systems.. Nanomanufacturing: typical bottom-up processes[r] ...
43