Al-Cu Based Alloys
Influence of Si and Ge Microalloying Additions and Plastic Deformation on Precipitation Processes in Al Cu Based Alloys
... In Al-Cu based alloys, different kinds of micro-alloying additions have been ...to Al-Cu have been shown to enhance the hardening rate and to increase peak hardness [2] [4] ...
17
Determination of the transformation exponent s from experiments at constant heating rate
... various Al-based based alloys is studied using ...water-quenched Al-6at%Si. Al-Si is a useful model system as it contains only two phases: the Al-rich phase and the Si ...
15
A model for the yield strength of Al Zn Mg Cu alloys
... multi-component alloys is presented and applied to overaged Al-Zn-Mg-Cu alloys (7xxx ...is based on an approximation of the strengthening due to precipitate by-passing during ...
36
Precipitates and intermetallic phases in precipitation hardening Al–Cu–Mg–(Li) based alloys
... stretched) alloys have been interpreted to show that the second stage of hardening is because of GPB ...non-stretched alloys to peak hardness, the S phase precipitation peak observed in DSC virtually ...
23
Formation, Thermal Stability and Mechanical Properties of Cu Zr Al Bulk Glassy Alloys
... glassy alloys in conjunc- tion with high stability of supercooled liquid against crys- ...glassy alloys with a large supercooled liquid region in Mg-, 1) lan- thanide (Ln)- 2) and Zr- 3) based alloy ...
5
Investigation of AlMgCu Alloy Corrosion in 0.5M NaCl: Polarization and EIS studies
... of Cu and ...for alloys 4 and 5, with Mg/Cu ratios of ...by alloys 4, 5 and 6, in accordance with the increase in Cu content (from ...wt. Alloys with higher Cu content are ...
10
Relationship Between the Liquidus Surface and Structures of Zr Cu Al Bulk Amorphous Alloys
... amorphous al- loy is merely depend on the phase diagrams, because a high melting (eutectic) temperature brings about a thermal affect as exemplified structural relaxation embrittlement, and a steep slant liquidus ...
5
Strength modelling of Al Cu Mg Type alloys
... the Cu-Mg co-clusters at room temperature after the alloy has been underaged at high ...the Cu-Mg co-clusters and the S ...2024-T351 alloys [11, 30, ...predicted based on alloy composition and ...
229
Surface Characterization of Amorphous Zr Al (Ni, Cu) Alloys Immersed in Cell Culture Medium
... Zr–Al–Cu alloys were calculated as listed in Table ...both alloys were similar each ...both alloys was reduced because concentra- tions of carbon and nitrogen were too ...both ...
6
Mechanism of Intergranular Corrosion of Brazed Al Mn Cu Alloys with Various Si Content
... The results show that the variation of IGC susceptibility corresponds with the change in the potential difference be- tween the grain boundaries and the grain interiors with in- creasing amount of Si added. Furthermore, ...
8
A model for the electrical conductivity of peak aged and overaged Al Zn Mg Cu alloys
... overaged Al-Zn-Mg-Cu (7xxx series) alloys is ...7xxx alloys including both Zr containing alloys and Cr containing alloys under various ageing conditions, achieving an accuracy of ...
29
Two types of S phase precipitates in Al Cu Mg alloys
... et al [22] suggested that there would be 24 instead of 12 precipitate orientations if these two types of S precipitates ...these alloys [22]. This was based on the assumption that Types I and II ...
11
Damping Properties of Ductile Cu Al Mn Based Shape Memory Alloys
... decreasing Al content. 5) There- by, Cu-Al-Mn alloys with low Al content below 18 at% have an excellent ...Ti-Ni alloys, can be obtained by microstructural control in ...
5
Recent Progress in Shape Memory Alloys
... memory alloys (SMAs) for the past 10 years was reviewed and research trends in the field were briefly ...novel alloys, such as the ductile Cu-Al-Mn SMA, ferrous superelastic alloys and ...
5
Melting and Corrosion Behavior of Al 9Zn Based Alloys with Cu and Mg Additions
... and Cu additions on melting, mechanical and corrosion behavior of Al-9Zn alloy was studied and ...of Cu and Mg led to form the Al-Cu, Al-Mg and Mg-Zn interme- tallic ...the ...
7
Application of uniform design in optimisation of three stage ageing of Al Cu Mg alloys
... Al-Cu-Mg based alloys (2xxx series) are widely used in structural applications, in particular alloys with Cu:Mg atomic ratio close to 1 are used extensively in the aerospace sector ...
22
Experimental Investigation of the Early Stage of Precipitation on Binary Al Li, Al Cu Alloys and Ternary Al Li Cu Alloys by Means of Atom Probe Tomography
... Aluminum-based alloys play a key role in modern engineering and are widely used in construction components in aircraft, automobiles and other means of transporta- tion due to their light weight and superior ...
20
Precipitation hardening in Al Cu Mg alloys revisited
... Fig. 1 shows two curves of hardness vs ageing time for samples aged at 190ºC and 150ºC, respectively. It shows that ageing at 190ºC for 6 hours is just short of peak ageing and 190ºC for 12 hours is at peak ageing. ...
12
Development of new damage tolerant alloys for age forming
... of Al-Cu-Mg-Li-(Zr-Mn) based alloys predicted to provide yield strengths in aged condition comparable with incumbent 2024-T351 alloy for lower wing skins are ...new alloys after ...
6
Japanese irogane alloys and patination – a study of production and application
... metal alloys came to great prominence in the sword furniture of Edo period Japan (1603-1868), from the somber shakudo work of the Goto family to the flamboyant inlays of the machibori ...
37