• No results found

Bearing Strength

BEARING STRENGTH OF POLYETHYLENE TEREPHTHALATE (PET) FIBRE REINFORCED RECYCLE AGGREGATE CONCRETE

BEARING STRENGTH OF POLYETHYLENE TEREPHTHALATE (PET) FIBRE REINFORCED RECYCLE AGGREGATE CONCRETE

... The bearing strength at ultimate state for all mixes is presented in Table 3 and Figure ...the bearing strength was ...the bearing strength is decreased from 8 to 41% for 25 to ...

10

BEARING STRENGTH OF SILICA FUME CONCRETE WITH AREA RATIO OF FIVE

BEARING STRENGTH OF SILICA FUME CONCRETE WITH AREA RATIO OF FIVE

... The bearing strength test was conducted on cubes. To analogous the column and footing, a steel plate 67mm (breadth) x 67mm (width) x 25mm (thick) was placed on cubes and tested in cube compression machine. ...

15

Plain and threaded bearing strength for the design of bolted connections with pultruded FRP material

Plain and threaded bearing strength for the design of bolted connections with pultruded FRP material

... the strength and response of bolted connections failing in bearing (pin or otherwise) are sensitive to bolt diameter, material thickness, fibre orientation and architecture, clearance hole size and ...

11

Bearing strength of steel fibre reinforced silica fume concrete

Bearing strength of steel fibre reinforced silica fume concrete

... the bearing stress can be checked at the inter surface of column and ...the bearing stress is function of characteristic compressive strength of ...compressive strength of concrete, the ...

5

Abstract — An analytical method for computing the stresses was developed to predict bearing strength of pinned

Abstract — An analytical method for computing the stresses was developed to predict bearing strength of pinned

... stresses, bearing strength and mode of failures of the ...reduce bearing stress, and thereby increase the joint strength, especially when it is not possible to increase the hole diameter due ...

7

Laterally unrestrained bearing strength of hot wet conditioned pultruded FRP material

Laterally unrestrained bearing strength of hot wet conditioned pultruded FRP material

... the strength and response of bolted connections failing with the bearing mode are sensitive to bolt diameter, material thickness, fibre orientation and architecture, clearance hole size and environmental ...

13

Effect of hot wet aging on the pin bearing strength of a pultruded material with polyester matrix

Effect of hot wet aging on the pin bearing strength of a pultruded material with polyester matrix

... Aged pin-bearing strengths have been determined for the web material in a pultruded wide flange shape (of size 203 x 203 x 9.53 mm), after the specimens had received hot-wet conditioning to simulate aging for an ...

43

Bearing Strength and Failure Modes Analysis of Carbon Reinforced Aluminium Laminate

Bearing Strength and Failure Modes Analysis of Carbon Reinforced Aluminium Laminate

... the bearing strength of the pin –loaded glass laminate by varying the geometrical configurations like e/D and W/D ...laminate strength is achieved for e/D and W/D ratios higher than ...the ...

6

Numerical evaluation of pin bearing strength for the design of bolted connections of pultruded FRP material

Numerical evaluation of pin bearing strength for the design of bolted connections of pultruded FRP material

... 2017 Numerical evaluation of pin-bearing strength for the design of bolted connections of pultruded FRP material.. Journal of Composites for Construction, 21 5.[r] ...

42

Grain Size Influence on the Compaction Aptitude and the Bearing Strength of the Gravel Lateritic Soils

Grain Size Influence on the Compaction Aptitude and the Bearing Strength of the Gravel Lateritic Soils

... greatest bearing strength and a good Optimum Moisture ...its bearing strengths, the material is usa- ble up to subbase layer and its behavior depends on the grain ...

14

Specific bearing strength of bolted composite joint with different glass 
		fiber reinforcement

Specific bearing strength of bolted composite joint with different glass fiber reinforcement

... the bearing strength behaviour of the laminates with different woven linear densities was ...the bearing characteristics of pinned joints in an orthogonal fabric and a non-orthogonal fabric with ...

6

Bearing Strength and Failure Behavior of Bolted GLARE Joints

Bearing Strength and Failure Behavior of Bolted GLARE Joints

... Finite element results validated with the experimental Based on the experimental observation described in the previous sections, bearing failure is mainly related by matrix and fiber compression damage. Therefore, ...

10

Load Bearing Strength of Innovative I-Shapes of Cold Formed Steel Sections

Load Bearing Strength of Innovative I-Shapes of Cold Formed Steel Sections

... yield strength of steel sheets used in cold-formed sections is at least 280 N/mm 2 , although there is a trend to use steels of higher strengths, and sometimes as low as 230 N/mm 2 ...

10

Using a hybrid heuristic to solve the balanced vehicle routing problem with loading constraints   Pages 255-280
		 Download PDF

Using a hybrid heuristic to solve the balanced vehicle routing problem with loading constraints Pages 255-280 Download PDF

... Particularly, (1) is defined to minimize the total distance traveled, (2) minimizes the total tardiness, in (3) the vehicle fleet is balanced by minimizing the difference between the most and the least loaded vehicles, ...

26

A Comparative Study on the Mechanical Properties of Laminated Veneer Lumber (LVL) Produced from Blending Various Wood Veneers

A Comparative Study on the Mechanical Properties of Laminated Veneer Lumber (LVL) Produced from Blending Various Wood Veneers

... Rotary veneers from spotted gum (Corymbia citriodora) and white cypress pine logs (Callitris glaucophylla) recovered from the native forest in Queensland, as well as Queensland plantation hoop pine (Araucaria ...

18

Experimental Investigation of Mechanical Properties of Impact Modified Polyvinyl Chloride Fly Ash Composites

Experimental Investigation of Mechanical Properties of Impact Modified Polyvinyl Chloride Fly Ash Composites

... Pin-bearing strength is obtained by tension testing a pin-loaded hole in a flat specimen (Figure 1(a) and Figure ...mm/min. Bearing strength was calculated as per ASTM D ...

14

Experimental Investigation on Clay with Rice Husk Ash and RBI Grade 81

Experimental Investigation on Clay with Rice Husk Ash and RBI Grade 81

... Clay: Clay is an expansive soil. It has the property to swell when comes in contact with water and it shrinks when water get evaporated from it due to increase in temperature. But as we know that clay particle is very ...

7

Stress distribution of secondary bending in single lap bolted joints with dissimilar joining plates and plate types

Stress distribution of secondary bending in single lap bolted joints with dissimilar joining plates and plate types

... to bearing failure known as critical W/d and e/d ...that bearing strength and micro- mechanism of failure are strongly dependent on lay- up ...reduced strength for larger ...

8

Effects of Geofoam Particles on Geotechnical Properties of Clay-dune Sand

Effects of Geofoam Particles on Geotechnical Properties of Clay-dune Sand

... compressive strength exhibited an incremental trend in the clay soil by increasing the geofoam ...compressive strength in the clay soil demonstrated an incremental trend by increasing the geofoam ...

18

A Study on the Effect of the Change of Tempering Temperature on the Microstructure Transformation of Cu-Ni-Sn Alloy

A Study on the Effect of the Change of Tempering Temperature on the Microstructure Transformation of Cu-Ni-Sn Alloy

... for bearing fabrication have to meet the requirements such as high fatigue strength, high seizure resistance, high wear resistance (include abrasive wear, adhesive wear, fatigue wear, corrosive wear erosive ...

8

Show all 10000 documents...

Related subjects