Mg alloy
Thermal analysis of cryogenic machining of Mg alloy using FEM
... Finite element modelling (FEM) has been used widely in machining to reduce the need for extensive experiments and help researchers to better understand the metal cutting mechanism though the prediction of information ...
5
Effect of Mg on the Sintering of Al Mg Alloy Powders by Pulse Electric Current Sintering Process
... After tensile test, microstructures of the fractured surfaces of Al-Mg alloy specimens prepared by PECS process were observed using SEM. Here, the results at sintering temper- ature of about 0.94 times as ...
6
Processing and Characterization of Porous Mg Alloy for Biomedical Applications
... porous Mg alloy with different measured porosities are shown in ...of Mg alloy ...between Mg particles as the structures will weaken the strength of porous Mg ...between ...
5
Solid Recycling of an AZ31 Mg Alloy with a Vapor Deposition Coating Layer of High Purity Mg
... AZ31 Mg alloy with vapor deposition coating layer of high purity Mg was ...AZ31 Mg alloy specimens with the pure Mg deposition coating layer of the 30 mm in thickness were ...
5
Gas Pore Formation in Lost Foam Casting of AZ91H Mg Alloy in Comparison with A356 Al Alloy
... the Mg alloy, though the Mg alloy has many distinct advantages over other construction materials, such as low density, high modulus, good machinability and availability, and is also used in ...
7
Grain Refinements of Al Mg Alloy by Hydrogen Heat Treatments
... We chose an Al–7.8 mass%Mg (Al–7.8Mg) alloy in per suiting the possibility of occurrence of HDDR phenomena. Then, the purpose of the present study is to investigate of occurrence of the HDDR phenomena and ...
5
Ultrastrong Mg Alloy via Nano-Spaced Stacking Faults.
... In Mg alloys, adding Gd and Y elements can lower the stacking fault energy (SFE) and make a full dislocation easily split into two partials [5, ...hcp Mg alloy has some characteristics analogous to ...
108
Corrosion Resistance of Super-Hydrophobic Coating on AZ31B Mg Alloy
... of Mg or Mg alloys usually occurs in the presence of water, and it is significant to prepare an anticorrosion super-hydrophobic surface on the Mg alloy surface for wide application of ...
11
Performance of Mg-air Battery Based on AZ31 Mg Alloy Sheets with Different Grain Sizes
... of Mg-air batteries. AZ31 Mg alloy sheets with different grain sizes were obtained through cold-rolling and ...AZ31 Mg alloy sheets with fine grain sizes have higher electrochemical ...
7
Effects of 2 mass% Li Addition on the AZ80 Mg Alloy
... also replotted in Fig. 6. As shown in Fig. 6, the tensile strength increases, but fracture strain decrease, with increas- ing strain rate for both alloys. The variation of tensile strength and fracture strain exhibits a ...
5
Potentiodynamical Research of Zn Al Mg Alloy System in the Neutral Ambience of NaCl Electrolyte and Influence of Mg on the Structure
... the alloy in a NaCl ambience has been de- ...Zn55Al alloy, which has been contained of Magnesium in various con- centrations in the studied environments, ...Zn55Al alloy with additive Magnesium, the ...
5
Lithium-magnesium Alloy as an Anode for Lithium-Sulfur Based Batteries
... (Li-Mg) alloy can also act as the anode of Li-S based batteries and perform comparably to ...Li-Mg alloy could be further improved by the surface nitridation and coating with a layer of ...
6
Technology for Recycling Magnesium Alloy Housings of Notebook Computers
... Figure 5 shows the results of the corrosion resistance test. In this figure, the corrosion of a recycled material progresses as recycling is repeated. The corrosion of a molding created from a material recycled 10 times ...
7
Effect of Roll Material on Surface Quality of Rolled Aluminum
... Al-Mg alloy appeared darkened, and the surfaces rolled with 440C and D2 were observed to have a higher density of dark patches than the 52100 rolled sample, as shown in Figure 37d-e, 38d-e and ...in ...
107
ANALYSIS OF MATERIALS FOR INDIAN LMV SUB- SYSTEMS: A STUDY
... Analysis of power train and their sub-components mass and percentages are presented in Table 2. It was found that percentage mass saving for aluminiu m a lloys is 39.36 followed by magnesium a lloys 47.23. Analysis of ...
7
Tensile Properties of Forged Mg Al Zn Ca Alloy
... Continuously-casted Mg-9Al-1Zn-1Ca (in mass%) alloy (Mg-Ca alloy) and Mg-9Al-1Zn alloys (Ca-free Mg alloy) were forged at 573 K and their mechanical properties were ...
5
Effect of Stresses for Electrochemical Calculations of Mg-Zn-In-Sn Alloy
... for Mg alloy Mg- Zn-In-Sn with stresses immersed in ...of Mg 2+ , which are measured via inductively coupled plasma (ICP) analysis and FACSIMILE software ...of Mg-Zn-In-Sn alloy ...
11
Creep Deformation Mechanisms in Coarse Grained Solid Solution Mg Alloys
... for Mg alloy. In Fig. 6(b), VGC’s area (surrounded by solid line-set) vanishes and will be possessed by Harper-Dorn creep, grain boundary sliding and DCC when no VGC is assumed (gray dot-line set). ...
6
The Effect of Ca and Zn on Microstructure and Hardness Properties of Mg-10Al-1Zn and Mg-10Al-5Ca-2Zn Alloy
... Before the melting process, the chamber was cleaned thoroughly with laboratory tissues that were soaked in acetone to eliminate contaminants. After chamber decontamination, the samples and Ti getter were placed inside ...
6
Effect of Iron and/or Carbon on the Grain Refinement of Mg 3Al Alloy
... necessary that the particle lies inside a grain. As expected, many tiny particles could be observed in the samples of Mg- 3Al alloy modified by Fe (as shown in Figs. 1(c) and 1(d)) and these tiny particles ...
6