Mg alloys
Improvement of Mechanical Characteristics in Severely Plastic deformed Mg Alloys
... Mg alloys have become attractive as a light and highly efficient eco-material for high performance applications such as the components of automobile and electronics because of their low density, high specific ...
5
Effect of Mg Content on Stress Corrosion Cracking of Al-X Mg Alloys
... Al-Mg alloys are upon exposure to corrosive electrolyte such as seawater, the potential difference between the β-phase precipitate and the Al matrix causes formation of a microgalvanic ...Al-Mg ...
14
Effect of Trace Additions of Ag on Precipitation in Al Mg Alloys
... Alloys of the Al–Mg system have been a recent focus of attention for applications in the automobile industries, because they possess a combination of high specific strength, relatively good formability, ...
7
Two types of S phase precipitates in Al Cu Mg alloys
... Al-Cu-Mg alloys, which indicates the dense precipitates, which were in this work shown to be Type I, as ...series alloys Type II is more stable than Type I and hence also the third choice of phase ...
11
A Comparative Investigation on the Corrosion Behavior of cast and rolled ZG21 Mg Alloys
... cast Mg alloys will change greatly after forming treatment, possible from micrometer scale with network distribution to nanometer scale with discrete distribution, which will dramatically influence the ...
17
Precipitation hardening in Al Cu Mg alloys revisited
... used alloys in aeronautical industry is 2024 ...Al-Cu-Mg alloys are observed, separated by a ...Al-Cu-Mg alloys are formation of Guinier-Preston-Bagaryatsky (GPB) zones [1], ...
12
Low Energy Optical Absorption Peak in Aluminum and Al Mg Alloys
... Measurements of the absorptivity of Al and dilute Al-Mg alloys were made at 4.2 K in the 0.2- to 5-eV energy region by a calorimetric technique. In addition to the well-known conductivity peak around 1.6 ...
5
Creep Deformation Mechanisms in Coarse Grained Solid Solution Mg Alloys
... pure Mg fall within these two ...solution Mg alloys with high Al content compared to pure Mg or dilute Mg-Al alloy is due to the higher dislocation density in the ...since Mg-Al ...
6
Effect of Mg Content on Vibration Fracture Resistance of Friction Stirred Al Mg Alloys
... the Mg content ...2.5 Mg sample mentioned in the previous section. The correlation between Mg content and vibration cycle numbers is shown in ...solute Mg is found to be one of the dominant ...
8
Effect of CaO Addition on the Ignition Resistance of Mg Al Alloys
... of Mg and Mg-Al Mg alloys (pure Mg, AZ31, AM60, and AZ91) with CaO addition through the furnace chip ignition test, DTA under dry air, and torch ignition test under an ambient ...
6
Investigation on the Microstructure and Mechanical Properties of Mg Al Yb Alloys
... creep-resistant Mg-Al alloys with RE have already been developed, not many investigations have been reported in the literature concerning the effect of RE addition on the mechanical properties of Mg ...
8
Hydrogenation Properties of Partially Remelted Mg Ni Alloys
... Thixotropic Mg alloys have been focused only on the aspect of semi liquid forming until ...in Mg-(3, 6, 9, 12 mass%) Ni alloys by using a partial remelting ...analysis, Mg rich solid ...
7
Corrosion Performance of as-rolled Mg-8Li-xAl Alloys
... (Mg) alloys, the lightest structural metal in the world, are considered as a potential alternative to other metallic structural engineering materials ...[1-3]. Mg alloys have low density, ...
12
Biodegradable stents made of pure Mg and AZ91 alloy through SPS sintering
... these alloys are produced by casting technologies and then submitted to hot working ...for Mg alloys because the powders display a high reactivity to oxygen and thus, easily form oxides on their ...
121
Grain Refinement and Superplasticity Induced by Hot Compression of Continuously Casted Mg 9Al 1Zn 1Ca and Mg 9Al 1Zn Alloys
... The Mg-9Al-1Zn-1Ca and Mg-9Al-1Zn alloy billets with the diameter of 155 mm, prepared by continuous casting method, were purchased from Sankyo Material, ...the alloys are listed in Table 1. Some of ...
8
The Effect of Ca and Zn on Microstructure and Hardness Properties of Mg-10Al-1Zn and Mg-10Al-5Ca-2Zn Alloy
... The alloys melting was prepared in arc melting furnace on a water-cooled Cu hearth in Argon (Ar) ...the Mg alloy was refined at 720 ◦C and then held for 20 minutes before ...
6
Characterisation of the precipitation in Al Li Cu Mg (Mn, Zr) alloys
... new alloys from the 2xxx series which have enhanced formability but still retain good mechanical ...Al-Cu-Mg alloys has the double advantage of reducing their density and increasing their elastic ...
14
Hydrogen Storage in Mg and Mg Based Alloys and Composites Processed by Severe Plastic Deformation
... commercial Mg alloys (such as ZK60) have good hydrogen storage capacities and kinetics that will depend on the processing ...Such alloys can be processed by SPD or extensive plastic deformation ...
10
Evolution of Mechanical Properties and Microstructure in Extruded Mg96Zn2Y2 Alloys by Annealing
... temperatures are shown in Fig. 2. The yield stress and tensile strength of the as-extruded specimen were 391 and 432 MPa, respectively, and the elongation was 5.4%. When annealed at 623 K, above which temperature the ...
6
Electrochemical performance of Mg-Al-Zn and Mg-Al-Zn-Ce alloys as anodes for Mg-air battery
... of Mg alloys is to alloy Mg with other elements, such as Al, Zn, Sn, Pb, In, Ga, and RE ...magnesium alloys have been widely used and studied as anode materials ...magnesium alloys to ...
13