Negative electrodes
A Commercial Conducting Polymer as Both Binder and Conductive Additive for Silicon Nanoparticle Based Lithium Ion Battery Negative Electrodes
... battery negative electrodes where multiple non-active electrode additives (usually carbon black and an inert polymer binder) are replaced with a single conductive binder; in this case the conducting polymer ...
29
Electrochemical Properties of Si Negative Electrodes Bonded with Partially Hydrolyzed Polyacrylamide for Li-ion Batteries
... containing the sodium carboxymethyl cellulose (NaCMC). The efficiency of NaCMC binder could be attributed to its extended conformation in solution that facilitates the formation of an efficient conductive material, ...
7
Effects of Negative Electrodes Coated by ZnO with Different Morphologies on Electrochemical Performances and Safety of Lithium Ion Batteries
... T-ZnO-coated negative electrodes are presented in Fig. 2. A pristine negative electrode consisted of natural crystal graphite spheroids of length 13–16 μm and width 40 ...the negative ...
11
A new type of lithium ion battery based on tin electroplated negative electrodes
... This work describes the preparation and the characterization of various samples of metallic Sn electroplated on a cupper foil under different current and time regimes. These samples have been characterized by XRD and SEM ...
12
Carbon based negative electrodes for li ion batteries
... It may be concluded that Li-ion rechargeable batteries may offer a high energy density, low toxicity alternative to existing primary and secondary battery technologies.... They may also [r] ...
169
Alginic acid-derived mesoporous carbonaceous materials (Starbon®) as negative electrodes for lithium ion batteries : Importance of porosity and electronic conductivity
... as negative electrode for lithium ion ...A800HPV electrodes can be formulated without carbon black without impacting the electrochemical performance, contrary to NC ...
26
Sustainable polysaccharide-derived mesoporous carbons (Starbon®) as additives in lithium-ion batteries negative electrodes
... other electrodes (up to 60 mV for LTO-Y50A, ...of electrodes formulated with other carbons ...Other electrodes such as LTO-Super P or LTO-Y50A gave only 70 to 80 % capability retention under the same ...
9
Titanium dioxide nanomaterials as negative electrodes for rechargeable lithium ion batteries
... A class of non-graphitic or disordered carbons are the hard carbons. These materials are obtained by pyrolysis of non-expensive precursors, such as phenolic or epoxy resins, or natural carbohydrates, such as sugar, ...
216
Three-dimensional Ni3Sn4 Negative Electrodes for Lithium-Ion Batteries
... A three-dimensional architecture was proposed as a step change that can provide new exciting opportunities to significantly improve the performance of LIBs. Accordingly, various concept designs of three-dimensional ...
10
Effect of Compression on Negative Lead-Acid Battery Electrodes Doped with Glass Fibres
... of negative electrodes are ...positive electrodes with ...in negative active mass pores when the battery is without current charge or in the PSoC ...the negative active mass, the pores ...
14
Mass-Balancing of Electrodes as a Strategy to Widen the Operating Voltage Window of Carbon/Carbon Supercapacitors in Neutral Aqueous Electrolytes
... mass-balancing electrodes with respect to electrochemical performance of carbon-based supercapacitors (SCs) is ...and negative electrodes in SCs using the same active material in both ...
15
Carbon Xerogel and Manganese Oxide Capacitive Materials for Advanced Supercapacitors
... the negative and the positive ...the electrodes and the cycling stability of the ASC for improving capacitance ...of electrodes and electrolytes influence the electrochemical performance of ...
17
Cell voltage versus electrode potential range in aqueous supercapacitors
... In summary, we have studied and compared the maximum char- ging voltage (MCV) of aqueous supercapacitors with various elec- trode materials. The capacitive potential ranges (CPRs) and the capacitance ratio of the ...
8
Negative Lead-Acid Battery Electrodes Doped with Glass Fibres
... in negative lead acid electrodes cause nearly the same effect as carbon or titanium dioxide in prolonging the cycle life during partial state of charge in hermetic ...of negative active mass ...
14
Estimation of some Organophosphorus Pesticides Using Carbon Paste Electrode Coupled with Molecularly Imprinted Polymers Yehya Kamal Al-Bayati
... chlorpyrifos electrodes were investigated using two plasticizers have different polarities, including (TCP) and (DDBP) and MIP (w/w) ratios were studied to determine the influence of the amount of plasticizer in ...
7
Structural principles to steer the selectivity of the electrocatalytic reduction of aliphatic ketones on platinum
... Pt(111) electrodes, the activity of stepped Pt(100) electrodes increases with step density.. The most 193[r] ...
27
Phase Structure and Electrochemical Hydrogen Storage Characteristics of La0.7Ce0.3Ni3.85Mn0.8Cu0.4Fe0.15-x(Fe0.43B0.57)x (x = 0-0.15) Alloys
... improved the activation ability and the high-rate dischargeability of the alloy electrodes. The addition of B element has been proved to be effective to enhance the activation performance and the high-rate ...
10
Detection Of Dielectric Material Using Miniature Two-Plate Electrical Capacitance Sensor
... Electrical Capacitance Sensor (ECS) is a type of a non- destructive testing technique. This system is adopted from the Electrical Capacitance Tomography (ECT) concept which is become utmost mature between various ...
24
New Technique for Efficiency Enhancement of Film Electrodes Deposited by Argon Gas Condensation from Metal Chalcogenide Sources
... and n-type respectively [38]. Due to improvement in dark current, photoactivity 34.8 % has been achieved. There was only slight lowering in dark current at voltages more positive than + 0.8 V for film deposited from ...
13
Microstructures and Electrochemical Properties of LaNi3.55Co0.2-xMn0.35Al0.15Cu0.75(V0.81Fe0.19)x Hydrogen Storage Alloys
... All the alloy electrodes for test were prepared by cold pressing the mixture of 0.15 g alloy powders of 200-400 meshes and 0.75 g nickel carbonyl powders into a pellet of 10 mm in diameter under 15 MPa. ...
12