Parameters used for intra-cavity modelling
High Power Pulsed Intra-Cavity Frequency Doubled Vertical Extended Cavity Blue Laser Arrays
... external cavity provides the necessary feedback to enable lasing. The intra-cavity power in the external cavity is higher than would be obtained from a standard ...external cavity ...
9
Enhanced photoacoustic spectroscopy sensitivity through intra-cavity OPO excitation
... Figure 5. Sensitivity of the system to ammonia on absorption line 6605.6cm -1 4. FUTURE WORK Results achieved in this study demonstrated significant improvement of photoacoustic spectroscopy sensitivity, resulting from ...
8
Intra-cavity spectroscopy using amplified spontaneous emission in fiber lasers
... for intra-cavity absorption spectroscopy giving a path length enhancement of in the linear regime of operation for very weak ab- sorption lines or low gas concentrations, transforming a 6 cm path-length, ...
7
Flow Modelling Of Nasal Cavity With Various Flow Rate
... Nasal cavity is one of the organs in the human respiration system. Nasal cavity acts as the air flow passage for human ventilation and ...nasal cavity can change the flow behaviour and the flow ...
24
Modelling the inhalation of drug aerosols in a human nasal cavity
... 2.2. Segmentation & Surface Reconstruction A 2D segmentation is used to detect and extract, slice by slice, the walls of the airway. For the segmentation process, a region growing algorithm, based on the Mumford ...
7
Simultaneous intra-cavity detection of some physical effects in a CO 2 laser
... The chart presented in Fig.5, shows the high correlation coefficients of the three signals with the laser power. The PPE signal has the highest correlation coefficient for modulation frequencies and laser gas pressures ...
6
Heat, air and moisture transport modelling in ventilated cavity walls
... widely used external wall type in north-western Europe with a good moisture tolerance in cool humid ...a cavity wall configuration with a brick veneer outside leaf and a wood fibre board inside leaf is ...
29
Modelling nanoparticles parameters for antimicrobial activity
... main parameters which should be considered for nanoparticles antimicrobial ...to modelling these complex parameters to assess key variable parameters variation the role they play for the ...
20
Space and time modelling of intra-urban air pollution
... current modelling processes generally do not usually take into account the errors in many of the assumptions ...model parameters to give a distribution of exposure ...Probabilistic modelling ...
261
Modelling intra-regional geographic mobility in a rural setting
... Modelling intra-regional geographic mobility in a rural setting ∗ David Philip McArthur † , Inge Thorsen ‡ and Jan Ubøe § Abstract Large-scale models are often used in the urban planning context to ...
26
Modelling the Cavity of Continuous Chemical Lasers (CCLs) Using Matlab Applications
... map cavity in 3D Figure ...designations used in this diagram are: ω the probability of transitions sti- mulated in the channel from oscillation (channel 2-1); ω ...
5
Discrete element modelling and cavity expansion analysis of cone penetration testing
... model used in this study comprises a refined sample of spheres simulated in a 30° segment of a calibration chamber, shown in Figure ...samples used consist of a minimum of three zones of different-sized ...
27
Modelling the Intra-Metropolitan Location of Foreign Investment Firms in Istanbul
... been used in the analysis of the obtained data from questionnaires of foreign investment firms where was active in both service and industry ...was used for summarizing many variables by a few ...were ...
21
The definition of input parameters for modelling of energetic subsystems
... Each used component in the model has to be de- scribed, simulated and evaluated ...or parameters, the simulation of an individual subsystem does not have to be ...are used to find out the stable state ...
8
MODELLING AND OPTIMIZATION OF WIRE EDM PROCESS PARAMETERS
... machining parameters for performance measures of surface roughness in the WEDM ...is used to obtain optimum parameters combination for maximization of MRR and minimization of surface ...
11
Adjuvant chemotherapy for brain tumors delivered via a novel intra cavity moldable polymer matrix
... resection cavity after surgery and begins to solidify into a matrix at body temperature, adhering to the surgical cavity ...the cavity wall as observed when applied surgically ex vivo, refines and ...
12
Clinical Parameters of Oral Cavity, Physical and Microbiological Properties of Saliva in Patients with Obesity
... Złe nawyki żywieniowe czy wszechobecny cu- kier dodawany do większości produktów spożyw- czych to poniekąd wspólny mianownik chorób bę- dących plagą XX i XXI wieku. Zarówno otyłość, jak i próchnica zębów to choroby ...
9
Identification of parameters for Hill Curve used in general anesthesia
... and intra-patient variation of the hypnotic state, the model-based controller with adaptation on prediction model is a suitable ...model parameters to be adapted is as low as ...of parameters. ...
8
Properties of Estimates of Daily GARCH Parameters Basaed on Intra-Day Observations
... gent conditions are req uired, which may not b e met in (for ex ample ) asset-re turn data. The second p ot en tial strat egy is t o use the observ ation of Ande rsen and Bolle rslev (1998) that the volatility of low-f ...
28
Reduced order modelling for a rotating cavity flow using proper orthogonal decomposition.
... and 72% for Model A and B respectively) but Model A has a CPU time to com- plete a rotor-disc revolution one order of magnitude lower than that of Model B, the former seems to better represent the characteristics of a ...
165