Three-dimensional (3D) printing
“Three-Dimensional Printing” – A New Vista for Periodontal Regeneration: A Review
... resolution three-dimensional imaging of bony topography obtained by CBCT allows the development of image-based scaffolds which can fit precisely in defect morphologies around ...3D printing, and ...
5
Original Article Clinical effect of three-dimensional printing assisted less invasive stabilization system (LISS) to treat femoral intercondylar fracture
... Three-dimensional printing got rapidly progress in orthopaedics field ...3D printing, surgery time and blood loss could be reduced for completed preop- erative preparation and less intra-trau- ...
6
Packing Irregular Shapes For Three-Dimensional Printing: A Bibliographical Study
... This study mainly explores two databases that are Scopus and WoS (Web of Science) by using a combination of keywords for the analysis purpose. Both databases have resulted in somewhat similar level of results but the ...
7
Of PhDs, Pirates, and the Public: Three-Dimensional Printing Technology and the Arts
... of three-dimensional printing, three-dimensional scanning, and the Internet will erode the dividing line between the physical and the digi- tal worlds and will bring millions of ...
26
A DECISIVE OVERVIEW ON THREE DIMENSIONAL PRINTING IN PHARMACEUTICALS
... Three dimensional printing (3DP) is particularly an emerging technology expected to develop pharmaceutical manufacturing along with other ...minutes. Three situations where this on-demand ...
8
Regulating Three-Dimensional Printing: The Converging Worlds Of Bits And Atoms
... 3D printing, none offers a holistic analysis or suggests an overarching regulatory ...3D Printing: It’s No “Use,” 23 F ORDHAM I NTELL ...Rideout, Printing the Impossible Triangle: The Copyright ...
71
Experimental study of PLLA/INH slow release implant fabricated by three dimensional printing technique and drug release characteristics in vitro
... of three dimensional printing (3DP) technique had received wide at- tention [6-8], since the technique was first introduced by Sachs ...the printing head very ...
11
Three-Dimensional Printing Model as a Tool to Assist in Surgery for Large Mandibular Tumour: a Case Report
... The model is shown in Figure 4. The tumour of dimensions 55 x 40 x 22 mm was completely covered with thin cortical bone. The IAN was at the inferior border of the mandible. Cortical bone thickness around the lesion was ...
7
Accuracy of Rapid Prototyping Biomodels Plotted by Three Dimensional Printing Technique: Ex Vivo Study
... The rapid prototyping biomodels manufacturing is a recent technology with great importance in oral and maxillofacial surgery. It provides a better surgical planning, decrease of anesthesia time and great functional and ...
5
Development of palm oil based fly ash powder binder system for three dimensional printing
... of dimensional accuracy and mechanical properties, formulations with binder content of 30–40% were found to give the optimized properties for three dimensional printing of ...The ...
44
Three-dimensional printing models in congenital heart disease education for medical students: a controlled comparative study
... 3D printing process was performed to pro- duce lesion-specific ...of three ventricular septal defects (VSD) (subarterial, membranous, and muscular types, one for each) were exported from insti- tutional ...
6
Efficacy evaluation of three-dimensional printing assisted osteotomy guide plate in accurate osteotomy of adolescent cubitus varus deformity
... 19.0 software (Materialize, Leuven, Belgium) to generate three-dimensional reconstructed upper limb models. Then, the osteotomy plane was defined parallel to the articular surface 1 cm above the olecranon, ...
9
Three-Dimensional Printing and a Laissez-Faire Attitude Towards the Evolution of the Products Liability Doctrine
... 48. The inability to examine a product with the naked eye will require experts in the fields of 3D printing and engineering to determine exactly what caused the defect. While the cost of their opinions may prevent ...
29
Three-Dimensional Printing Using Recycled High-Density Polyethylene: Technological Challenges and Future Directions for Construction
... The key design concept here was the use of an arch roof as the main spanning slab for the entire 3D-printed house. Such arch-like structures have long been known to reduce tensile stress over long spans [32]. The arch ...
24
Case Report Three-dimensional printing technology facilitates customized pelvic prosthesis implantation in malignant tumor surgery: a case report
... The designed prosthesis was then saved as an STL file and input into an EOS M290 3D metal printer (Germany). The printing of the titanium alloy personalized prosthesis was completed in about 20 hours. Meanwhile, ...
6
Three-dimensional printing technology for treatment of intracranial aneurysm
... patients. The reason of choosing unilateral approach de- pends on the aneurysm pointing direction [16]. Aneu- rysms pointing in lateral, anterior or posterior directions are more difficult to clip from the contralateral ...
10
Antenatal Three-Dimensional Printing of Aberrant Facial Anatomy
... of three-dimensional (3D) modeling and 3D printing of complex fetal maxillofacial anatomy after prenatal ultrasound indicated potential upper airway obstruction from a midline mass of the ...
6
Direct three dimensional printing of polymeric scaffolds with nanofibrous topography
... The PLLA gel formed by TIPS was directly printed layer-by-layer with a speed of 18 mm/s to rapidly generate a 2x2x1 cm 3 self-supporting lattice structure with interconnected pores (250 µm-sized pores, 800 µm-diameter ...
32
Harnessing smartphone technology and three dimensional printing to create a mobile rehabilitation system, mRehab: assessment of usability and consistency in measurement
... The mRehab system was updated to more closely resem- ble household items and better guide the individual through the activities (further described in the results section). Figure 5 shows the updated 3D printed objects ...
13
A REVIEW ON NOVEL APPROACH TO PHARMACEUTICAL DRUG DELIVERY: 3D PRINTING
... of three-dimensional printing for the elaboration and distribution of controlled drugs plays a vital role in the current pharmaceutical industry, considering that drugs can be designed according to ...
7