Ti-C
Effect of Al-Ti-C-La Composite Alloy on Microstructure and Mechanical Properties of 6063 Aluminum Alloy
... Abstract: In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure ...
15
(Ti,Cr)C Synthesized In Situ by Spark Plasma Sintering of TiC/Cr3C2 Powder Mixtures
... The mechanical properties of (Ti,Cr)C consolidated by SPS are summarized in Table 2. The hardness values of (Ti,Cr)C from both mixtures were almost identical. It was 23.0 and 22.9 GPa for the ...
5
Microstructure and Grain Refining Performance of a New Al-Ti-C Master Alloy (RESEARCH NOTE)
... Al, Ti, and TiC ...while Ti and TiC powder particle sizes ranged from 1 to 5 ...wt Ti and 93% wt Al powders, and the other 5% wt TiC and 95% wt Al ...
6
Twisting Relaxed Tensile Strength and Its Reliability of Si Ti C O (Tyrano) Fiber
... Although the twisting relaxation decreases the initial slope of stress–strain curve (see Fig. 4), the twisting relaxation elongates the fracture strain. As a result, the elongation mainly enlarges the fracture stress. ...
5
Effect of Sintering Temperature on the Microstructure and Properties of Ultra Fine Ti(C,N) Based Cermets
... the Ti(C,N) matrix, the fracture surfaces of the reacted sam- ples were ...the Ti(C,N) particles often ex- hibited a polyhedral morphology, 10,14) as shown by the EDS ...
5
Metal Ceramic Smart Composite in Ti(C,N) Ni Mo W System
... Compressed and dried specimens were sintered at various temperatures in vacuum furnace at 1600˚C with 50˚-interval. After sintering the specimens were visually inspected and setting, water absorption, density and ...
10
The influence of thermal history on the hot ductility of Ti containing C Mn Al and C Mn Nb Al steels
... List of Symbols a y Do Ferrite phase Austenite phase Delta phase Grain size D,, Df L [ ]x[ ] p or ps n; s; CR Initial, final diameter Liquid phase Product of solubility Particle size Num[r] ...
219
Retroviral DNA Methylation and Epigenetic Repression Are Mediated by the Antiviral Host Protein Daxx
... the TI-C pop- ulation, is provided in the top panel of ...in TI-C, TI-L, and TI-E cells were analyzed, including the LTRs, two areas of the env gene, the internal CMV promoter, ...
14
Effect of Milling on the Carbothermal Reduction of Oxide Mixture for (Ti,W)C Ni
... or Ti(CN)-based cermets and the poor wettability of the Ni binder phase on the ...or Ti(CN)-Ni system is effective in improving the toughness and is decreasing the particle growth ...
6
Preparation of Ti Matrix Composites of Ti B C N Systems by Spark Sintering and Their Friction and Wear Characteristics
... of Ti, Fe and B are shown in ...of Ti as a main element on the worn surface in the ring, see ...in Ti-concentration profile, corresponded to adhesive films showing in ...in Ti-concentration ...
8
Microstructural Evolution of Ti Mo Ni C Powder by Mechanical Alloying
... was a typical fcc Debye ring of polycrystalline structure (Fig. 5(b)). As a consequence of the diffraction pattern, the lattice constant was estimated to be 0.4315 nm. This value is smaller than that for TiC (0.43274 nm), ...
6
Effects of Cryo Treatment on Corrosion Behavior and Mechanical Properties of Laser Welded Commercial Pure Titanium
... of Ti before and after laser ...for Ti became smaller after ...laser-welded Ti after cryo-treatment exhibited the most obvious passivation behavior of all the ...of Ti, cryo-treated Ti ...
6
Effect of Titanium Carbides on the Ductility and Toughness of High Carbon 30 mass% Chromium Steels
... containing C and Ti were melted from electrolytic iron and electrolytic chromium by a high frequency vacuum induction ...The Ti/C ratio of the two specimens is nine ...
6
Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy
... Titanium alloys due to its low weight, high strength and good biocompatibility are widely used in aerospace, military, chemical and medical industries [1, 2]. However its poor wear resistance and low tribo-corrosion ...
15
Theoretical Study of Laser Emission for C Like (Ar XIII), (Ti XVII) and (Fe XXI)
... XIII, Ti XVII & Fe XXI ...XIII, Ti XVII & Fe XXI ions) together with the calculated parameters could be achieved experimentally, then successful low-cost electron collisional pumping XUV and soft ...
17
Novel aluminium alloys for thermal spray applications to steel substrates
... a c ita n c e (Cdi), h o w ever during modelling a constant p h a s e e le m e n t (CPE) m ay be used to rep resen t a non ideal capacitor, or, an Inductor (L), which rep resen ts ...
461
On Modeling and Maximizing Online Customer Group Value
... This study established online customer lifecycle value model as follows [2]: Ni-1 Ni E i 1 f ti Bti CLVi p ti 1+d Ni ti n Ni 1 d ti Ni ti 0 ti Ni 1 ti[r] ...
6
Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy
... layer of Fe atoms adhered on plane specimen (Fig. 10 Plane TW12) which slows down the abrasive wear kinetics. In this case, there is no transfer of Ti particles on the sphere specimen (Fig. 10 Sphere TW12). Wear ...
17
The politics of trade unionism in a sweated industry : boot and shoemakers in late nineteenth century London
... relief» c o u l d obtain it from the Ru sso-Dewish Conjoint C o m m i t t e e if they could p r o v e that they had been victims of pe rsecution in ...ia ti on ; to h e lp f i nd work for immigrants ...
450
Effect of Cooling Rate on Superelasticity and Microstructure Evolution in Ti 10V 2Fe 3Al and Ti 10V 2Fe 3Al 0 2N Alloys
... as Ti-Ni alloys, its shape memory and superelastic properties are often improved by heat treatments after the solution ...a Ti-10V-2Fe-3Al alloy with a small amount of nitrogen after solution ...
6