[PDF] Top 20 Explorer Digital Set-Top User s Guide

... This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such ... See full document

... On: S M T W T F S Home phone _______ from _______ to _______ On: S M T W T F S Mobile phone _______ from _______ to _______ On: S M T W T F S Pager _______ from _______ to ... See full document

... In the lin_tape drivers with level lower than 3.0.3, the maximum transfer length per device per SCSI command is 262144 bytes (256 KB) by default. Variable block read/write requests with transfer length greater than the ... See full document

... • The camera is set to your country’s AC mains frequency. If you use it in another country with different frequency (either 50 or 60Hz), you should not take the photo under the lamp.Black strips of line will be ... See full document

... This publication refers to Telrad Connegy's Avanti 3015 set and Avanti 3000 set connected to Telrad Connegy’s UNITe IP system, Release e2e-1, as of May, 2003. Telrad Connegy reserves the right to modify the ... See full document

... To create a one-time-only scheduled backup to run at some time in the next seven days, leave the "Single Backup" radio button checked. Next, set the time and day you would like the backup to run, and click ... See full document

... Always monitor the line for an audible signal before attempting to go off-hook to draw dial tone. The data detect circuitry on the test set is designed to detect data signals above the human audio range. To detect ... See full document

... You can schedule activities either for yourself or for your assistant. You can also set reminders so that you never forget to complete important tasks. Then once you’ve completed the activity, you can mark it ... See full document

... Softkeys have several functions, which change according to the state of your telephone. A softkey's function, at any particular moment, is indicated on the telephone display. To operate a displayed function, press the ... See full document

... BY YOUR USE OF THE SOFTWARE INCLUDED WITH THIS PRODUCT YOU AGREE TO THE LICENSE TERMS REQUIRED BY THE LICENSOR OF THAT SOFTWARE, AS SET FORTH DURING THE INSTALLATION PROCESS. IF YOU DO NOT AGREE TO THE LICENSE ... See full document

... You may decide you would prefer certain incoming calls arriving at particular times of day or night to be handled in a different manner to that programmed in Part C, above. You can distinguish between calls that receive ... See full document

... their user status that they are available for operator ...you set your user status to one which indicates that you are available for operator ...additional user status definitions that only ... See full document

... emaGEN offers you two ways of reviewing your new and existing messages. You may choose to listen to them directly (as described below) or view a listing of all your messages on the display before selecting the ... See full document

... You may decide you would prefer certain incoming calls arriving at particular times of day or night to be handled in a different manner to that programmed in Part C, above. You can distinguish between calls that receive ... See full document

... you set Remove Prefix from NV Names, the nvi or nvo string will be removed from the beginning of the network variable's ...you set Remove Array Subscripts from NV Names, any endings of network variable ... See full document

... Effective principals prioritize instruction and student achievement by developing and sharing a clear definition of high-quality instruction based on best practices from research. They implement a rigorous curriculum ... See full document

... If you are using an LNS application that does not support monitor sets (groups of data points that the LonMaker tool uses to monitor and control network variables) and you are making many bound connections to the LNS ... See full document

... To comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules, this device must only be installed on computer equipment certified to comply with the Class B limits. In addition, only ... See full document

... Light reflecting back from eyes can make them appear red when the flash is used in dark areas. Under these conditions, use the red-eye reduction mode. For this mode to be effective, the subject must be looking right at ... See full document

... 4 Load bar Analog indicator to help identify when an overload condition is imminent. The bar increases either to the right or to the left from the midpoint of the graph. Increasing to the right indicates compression ... See full document