P=123 KF=1 YYY

P=123 KF=1 YYY

2. Press and set the operation of each of the 4 buttons of the key-fob. Set the parameters for the Arm button #1 (±) (used to perform the Full/Part Setting operation) from the following options:

ƒ None: The button is disabled.

ƒ Set: The button is used for full setting the assigned partitions (default). ƒ Part Set: The button is used for part setting the assigned areas.

3. Define if the Full or Partial Setting will be instant or delayed (following an exit delay) 4. Press . The system moves to the next key, and the following display appears:

Key-fob:1 Butt:2 1)None Ð Key-fob:1 Butt:2 1)None Ð

5. Set the parameters for the Disarm button #2 (²) (used to perform the unsetting operation) from the following options:

ƒ None: The button is disabled (default).

ƒ Unset: The button is used for unsetting its assigned partitions.

6. After selecting the required option, press . The system moves to the next button, and the following display appears:

Key-fob:1 Butt:3 1)None Ð Key-fob:1 Butt:3 1)None Ð

Fob:1 Butt:3 PO: 01)Output 1 Ð Fob:1 Butt:3 PO: 01)Output 1 Ð

8. After selecting the required option, press . The system moves to the next button, and the following display appears:

Kef-fob:1 Butt:4 1)None Ð Kef-fob:1 Butt:4 1)None Ð

9. Set the parameters for the button #4 (the small button), from the following options: ƒ None: The button is disabled (default).

ƒ Set: The button is used for full setting the assigned partitions. ƒ Part Set: The button is used for part setting the assigned partitions.

ƒ PO: The button is used to operate a Programmable Output. When selecting this option, you must select a Programmable Output:

NOTE:

Full or Part setting can be defined as instant or delayed (Exit Delay)

10.After selecting the required option, press .

11.Repeat the procedure to program the other wireless key fobs.

77 33

Key-fob: Communication Test

The Key fob communication menu enables to perform a communication test between the key fob and the WisDom’s receiver.

¾

1. Access the Key - Fob menu, as described above.

2. From the Key - Fob menu, press [3] to access the Communication Test menu options. The following display appears:

K-fob comm.test 1)Key-fob 1: -- Ð K-fob comm.test 1)Key-fob 1: -- Ð

3. Select the key-fob you wish to perform the test on.

4. In order to proceed, initiate a transmission from the selected key-fob by pressing on any of the buttons. A confirmation beep along with an OK message indicates a successful communication test.

The Keypads menu contains parameters that enable WisDom to allocate the data it receives from the wireless keypads. Up to 2 wireless keypad can be added to the system.

The wireless keypads are rolling code transmitters with the following options: Full Set, Part Set , Unset, Panic, and PO activation:

After you access the Keypads menu from the main Engineer Programming menu, as described in this section, you can access the following submenu:

88 11 _{Allocation, below}

88 22 _{Communication Test, page 4-87}

¾

From the main Engineer Programming menu, press [8] or use the or keys and then press . The following display appears:

Keypads:

1)Allocation Ð Keypads:

1)Allocation Ð

You are now in the Keypads menu and can access the submenu, as described in the sections that follow.

88 11

Keypads: Allocation

This procedure is required to assign a wireless keypad to the WisDom.

¾

1. Access the Keypads menu,.

2. From the Keypads menu, press [1] to access the Allocation menu options. The following display appears:

Keypad alloc.: Select=1 (1-2)

Keypad alloc.: Select=1 (1-2)

3. Select the keypad you wish to learn-in to the system. 4. Press . Three options are available, as follows:.

ƒ Press [1] to move to the next keypad assignment.

ƒ Press [2] to write (or overwrite) data into the selected location and allocate a Wireless Keypad. Send a write signal (within 255 seconds) from the keypad by pressing the ±(Set) key twice on the keypad. After each press the wireless keypad will send a beep and its Power LED will blink. If the WisDom successfully recognizes the wireless keypad it will sound a confirmation beep.

ƒ Press [3] to erase the data in the selected location. Select [Y] or [N] using the key and press to confirm your selection.

The Keypads communication menu enables to perform a communication test between the wireless keypad and receiver.

¾

1. Access the Keypads menu, as described above.

2. From the Keypads menu, press [2] to access the Communication Test menu options. The following display appears:

Keypad comm.test 1)Keypad 1: -- Ð Keypad comm.test 1)Keypad 1: -- Ð

3. Select the keypad you wish to perform the test on

4. In order to proceed, initiate a transmission from the selected keypad by pressing on any of the keypad keys. Allow a few seconds for the receiver to react.

A confirmation beep along with an OK message indicates a successful communication test . 5. Repeat the procedure to test an additional keypad or press to exit.

The More Devices menu contains parameters that enable the WisDom to expend its communication, signaling capabilities and enabling the security panel to support X-10 transmitters.

99 11 _{GSM, below} 99 22 _{Sounder, page 4-94} 99 33 _{X-10, page 4-97}

99 11

More Devices: GSM

The GSM /GPRS BUS module is a cellular communication module that can be used as a backup or a substitute to a normal PSTN line.

Reporting to the ARC can be performed using Voice, SMS or GPRS channel using RISCO's IP receiver at the ARC site.

99 11 11 _{Add / Delete GSM, page 4-88} 99 11 22 _{Communication test, page 4-88} 99 11 33 _{GSM Parameters, page 4-89}

¾

From the main engineer menu press [9] to access the “More Devices” menu. Press [1] for GSM. The following display appears:

Press [1] for the Add/Del GSM menu. The following display appears:

Configure the parameters as follows:

More Devices: GSM

Quick Keys Parameter Default Range

99 11 11 Add/Delete GSM

Press on the or on the key to select the GSM option.

TYPE=NONE: GSM deactivated

TYPE=GSM: GSM activated

99 11 22 Communication test

After allocating the GSM/GPRS BUS Module, it is recommended to perform a communication test in order to verify the BUS communication quality between

Quick Keys Parameter Default Range

BUS COM QUALITY