OPtiOnAl AcceSSOrieS
4 Rod loader
69 69
351433002 Steady rest · Passage Ø 10 mm up to Ø 130 mm
351433003 Follow rest · Passage Ø 10 mm up to Ø 100 mm
351433001 Hydraulic tailstock sleeve · for rapid processing
· Sleeve can be retracted and extended hydraulically 351433011 Quick-action tool changer Multifix 4 · Instead of the serial equipment - hydraulic turret VDI30
351433007 Hydraulic turret LS-120 · Standard type
· 8 tools
351433008 Tool holder kit
· for the hydraulic turret LS-120 (351433007) - Only for standard changer not VDI -
· 3 fixtures for reducing bushes · 1 fixture for external lathe tool · 4 reducing bushes
351433012 Rod loader PRO 1.20 metre 351433019 Rod loader PRO 3.20 metre
351433009 Portable electronic handwheel · Instead of the serial equipment - Joystick
351433013 Power transformer · for special clamping
· Weight 147 kg 1
2
3
4
6
Hydraulic tailstock
5
Portable electronic handwheel
2 Rests
Power transformer
quick change tool holder and turret
5
6
3
Lathe chuck „L44“ on page 104
PREM IUM PREM I UM
· High precision machine with latest SIEMENS control and SIEMENS servo drives · New compact structure of the headstock
· High-speed spindle 4'500 min-1 with high-precise, largely dimensioned taper roller bearings · Change-over between the two gears is performed pneumatically via the air cylinder · Headstock structure guarantees minimum noise development
· Wide machine bed with double rectangle slideways also for roughing work · Hardened and ground slide ways
· Largely dimensioned tailstock, travelling on two guideways, easy-to-position via carriage and is equipped with a quick clamping
· 2 front separately travelling sliding doors incl. integrated window
· Micro switches prevent starting up the machine if the protecting device is not completely closed and thus avoids the opening of the door
· RJ45 plug connection, USB connection and power connection 230V · Travelling operating panel
· Two electronic handwheels for manual operation of the X and Z axis · Automatic lubrication of the headstock
· Automatic lubrication of the saddle slide and the cross slide rest · Halogen work lamp
· Heat exchanger for switch cabinet · Two-year SIEMENS warranty included „Warranty extension“ on page 102
High performance. Additional speed. Highest precision.
SINUMERIK 828D Basic T
Siemens control
IncludIng:
Safety Integrated
Residual material detection and operation
Shopturn programming of working steps 3-D Simulation
Network preparation Simultan recording
Safety Integrated
Siemens
Set up with opened door
Fig. L 460
Fräs en Pr eamble Millin g Tur nin g Sof twa re A cc es so ries
** Depending on the installed chuck
71
Type L 440 L 460
Item No 3514410 3514420
Electrical connection
Electrical connection 400 V / 3 Ph ~50 Hz 400 V / 3 Ph ~50 Hz
Total connected value load 20 kW 20 kW
Spindle
Driving motor 11 kW (S1mode 9 kW) 11 kW (S1mode 9 kW)
Torque driving motor 70 Nm 70 Nm
Spindle nose DIN ISO 702-1 No. 6 DIN ISO 702-1 No. 6
Spindle bore Ø 65 mm** Ø 65 mm**
Coolant-lubricant system
Power of the coolant pump 375 W 375 W
Tank capacity without chip conveyor 170 litres 240 litres
Hydraulic system
Motor power 750 W 750 W
Tank capacity 50 litres 50 litres
Machine data
Centre height 235 mm 235 mm
Turning length max. 1'000 mm 1'500 mm
Turning Ø over cross slide 240 mm 240 mm
Turning Ø over machine bed 475 mm 475 mm
Turning Ø in the bed bridge 710 mm 710 mm
Hydraulic lathe chuck Ø 200 mm Ø 200 mm
Chuck through hole Ø 52 mm Ø 52 mm
Speed range
Spindle speeds Step 1 / Step 2 100 - 950 min-1 / 900 - 4'500 min-1 100 - 950 min-1 / 900 - 4'500 min-1
TorqueStep 1 / Step 2 525 Nm / 382 Nm 525 Nm / 382 Nm
Turret
Hydraulic type LS 160 VDI 40 LS 160 VDI 40
Number of tool positions 8 8
Fixture height, width square max. 25 x 25 mm 25 x 25 mm
Fixture diameter drill rod max. Ø 32 mm Ø 32 mm
Optional C axis
Motor 5 kW 5 kW
Torque motor 15 Nm 15 Nm
Spindle speeds 6'000 min-1 6'000 min-1
Accuracy
Repeatability ± 0.005 mm ± 0.005 mm
Positioning accuracy ± 0.005 mm ± 0.005 mm
Travel
X axis 260 mm 260 mm
Z axis 1'150 mm 1'680 mm
Feed speed
X axis 15'000 mm/min 15'000 mm/min
Z axis 15'000 mm/min 15'000 mm/min
Torque motor
X axis 6 Nm 6 Nm
Z axis 16 Nm 16 Nm
Tailstock
Tailstock seat MT 4 MT 4
Tailstock - sleeve diameter/travel 65 mm / 150 mm 65 mm / 150 mm
Dimensions
Length x width x height 3'030 x 1'952 x 2'025 mm 3'530 x 1'952 x 2'025 mm
Total weight 3'000 kg 3'450 kg
„Starter kit VDI 40“ on page 109 Standard equipment
· EMC
· Portable electronic handwheel · Hydraulic turret LS160 VDI40 · Hydraulic 3-jaw chuck Ø 200 mm · Hard and non-rigid block jaws · Heat exchanger
· Tailstock end cover · 6 pcs. Machine feet · Coolant equipment
· A lifting gear is required to unload the machine Lifting device 3514301
INFORMATION
Lathe chuck „L440“ on page 104 Starter kit VDI 40
Item No 3536116
· Generously dimensioned · Carriage with ball screw with
pre-stressed nut
· High-performance pump 375 W · Guaranteed repeatability
and positioning accuracy
· 3-jaw chuck hydraulic Ø 200 mm
· Passage 52 mm · Simple clamping of
work-pieces
· for clamping jaws lathe chuck and tool changer
· Motor power 750 W · Tank capacity 50 litres · Clamping pressure / Operating
pressure 2'500 - 2'942 kPa Laser measurement
· Precision bearings · Stable structure · Smooth running also at
high spindle speeds · Particularly broad design
· Ball screw drive for higher repeatability
· Pneumatic · Automatically
· The shaft is running in sin-tered bronze so that it is always lubricated and thus guaranteeing high accuracy Machine bed
Speed changer Headstock
· Efficient integrated heat transfer from the switch cabinet · Avoids that faults are generated
from the overheated electrical and CNC components
Heat exchanger
Fräs en Pr eamble Millin g Tur nin g Sof twa re A cc es so ries
OPtiOnAl AcceSSOrieS
Special equipment can only be ordered ex works.
For prices and other options please contact your dealer or send us an e-mail to: [email protected]
73 73
L440 L460
3514410 01 351442001 Internal tool cooling CTS 20 bars · Including external unit
3514410 03 351442003 Steady rest · Passage Ø 20 - Ø 200 mm
3514410 04 351442004 Follow rest · Passage Ø 20 - Ø 100 mm
3514410 16 351442016 Tool holder kit
· for the - hydraulic turret LS160 - in the serial equipment
· - Only for standard changer not VDI -
3514410 12 351442012 Turret Baruffaldi TBMA160 VDI40
· 8 tool positions · Tool drive · Hydraulic
· Instead of the serial equipment - turret LS160 VDI40 3514410 17 351442017 C axis brake system · only with turret Baruffaldi TBMA 160 VDI40
(3514410 12/351442012) 3514410 21 351442021 Hydraulic tailstock spindle
3514410 19 351442019 Machine preparation Hyd. Tailstock spindle
3514410 23 351442023 Pneumatic lifting device for the tailstock · Pneumatic air cushion reduces the friction thus easing the movement of the tailstock 3514410 22 351442022 Device to travel the tailstock simultaneously · Tailstock and support are coupled for travelling 3514410 33 351442033 Rod loader V65-E-Pro 1.25 metre ·Short rod loader on page 107
3514410 35 351442035 Rod loader DH 65 Fedek 1.25 metre ·Short rod loader on page 107 3514410 34 351442034 Rod loader V65-LE-Pro 1.5 metre ·Short rod loader on page 107 3514410 36 351442036 Rod loader DH 65 Fedek 1.5 metre ·Short rod loader on page 107
3514410 20 351442020 Portable electronic handwheel
· Instead of the serial equipment - electronic handwheel (cannot be combined with Joystick 3514410 02 / 351442002)
3514410 02 351442002 Joystick · to travel the X and Z axis (cannot be combined with
electrical handwheel 351441(2)0 20)
3514410 14 351442014 Air conditioning · Instead of the serial equipment - heat exchanger
3514410 07 351442007 Oil separator · including rotary disc, removes the oil from the
coolant, Capacity: 1 l per hour
3514410 13 351442013 Coolant pump · 5 bars
3514410 05 351442005 Chip conveyor · L 440: 1.0 metre - L 460: 1.5 metre
3514410 06 3514410 06 Chip carriage · Can be rolled, collapsed
· L x B x H: 994 x 510 x 838 mm 9 Chip conveyor
and carriage
C axis brake system