304L stainless steel
Analysis of friction stir welding process for 304l stainless steel
... This paper focusses on Friction stir welding (FSW) invented by Wayne Thomas in The Welding Institute (TWI) at London in 1991. Friction stir welding (FSW) is a solid state joining process which means joining of metal ...
5
Dynamic Mechanical Properties and Fracture Behavior of a 304L Stainless Steel GTAW Joint under Shear Conditions
... annealed 304L stainless steel plates and were then butt-welded using the manual Gas Tungsten Arc Welding (GTAW) process with a total of 14 welding ...
9
Metronidazole Performance as Corrosion Inhibitor for Carbon Steel, 304L Stainless Steel and Aluminum in Hydrochloric Acid Solution
... coordination of lone pairs of electrons with the d-vacant orbital of elements from alloy surface can take place (pure adsorption) [32, 40-42] as well as, their linkages can occur with metal cations formed by oxidation in ...
20
Effects of Hydrogen Water Chemistry on Stress Corrosion Cracking Behavior of Cold Worked 304L Stainless Steel in High Temperature Water Environments
... This study measured the stress corrosion cracking (SCC) growth rates of cold-worked 304L stainless steel in oxygenated and hydrogenated coolant environments. The effects of cold work at the levels of ...
5
The effect of substrate temperature of (Ti,A1)N coating on AISI 304L stainless steel and high speed steel using physical vapor deposition (PVD) method
... [1,2]. 304L stainless steel and high speed steel were chosen as the substrate material in this research and (Ti,Al)N hard coating was deposited because it has excellent high oxidation ...
24
The Effects of Trace PbO on the Oxide Behavior of 304L Stainless Steel in High Temperature Water
... 304L stainless steel was corroded in a simulated PWR primary circuit at 315°C with ppb level PbO treatment. Corrosion properties and semiconductor behaviors of the oxide layers on SS304L exposed to ...
11
Effect of Heat Treatments on the Electrochemical Behavior of 304L Stainless Steel in Nitric Acid
... of 304L stainless steel (SS) after heating at different temperatures and times was investigated by using the double loop electrochemical potentiokinetic reactivation (DL-EPR), the potentiodynamic ...
14
Comparison of Aggressiveness Behavior of Chloride and Iodide Solutions on 304 and 304L Stainless Steel Alloys
... and 304L stainless steel (SS) alloys was investi- gated by using the cyclic potentiodynamic polarization test at ...and 304L SS suffered from severe pitting corrosion at room temperature up to ...
10
Characterization of Gas Nitrided 304L Stainless Steel
... of 304L stainless steel to enhance the properties of components like wear resistance, fatigue resistance, and surface hardness without degradation of corrosion ...L stainless steel ...
8
Microstructual Study of the Dissimilar Joints of Alloy 690 and SUS 304L Stainless Steel
... This study was to characterize the microstructure of Alloy 690-SUS 304L stainless steel dissimilar weldments with Inconel 52 and 82 filler metals (I-52 and I-82). The weldments were butt-welded with ...
9
Corrosion Fatigue Behavior of Cold Worked 304L Stainless Steel in a Simulated BWR Coolant Environment
... In the corrosive environments, the FCGRs of 304 stainless steel specimens with prior cold work is about 7 times higher than those for the annealed ones. 18) The twins and grain boundaries are the preferred ...
7
Photomechanical Ablation of 304L Stainless Steel, Aluminum Oxide (Al2O3) Thin Film, and Pure Silicon
... In this work, the energy from a CO2 laser was used to ablate three different materials, namely, stainless steel 304L, a thin film of amorphous aluminum oxide Al2O3, and pure silicon, due[r] ...
15
Shear forming of 304L stainless steel – microstructural aspects
... al. [4] linked these forces to the process variables and in 2003, Kim et al. [5] obtained convergence of experimental and theoretical tangential forces by considering a pure shear model. Understanding the forces required ...
6
Cisplatin-chemotherapeutic Drug Interactions with the Surface of Some Metal Bioimplants in Physiological Serum
... for stainless steel in PS, without and with CisP, shown in ...the 304L stainless ...the 304L stainless steel surface morphology can be noticed in the presence of CisP that ...
14
Investigation on Various Aspects of using Activated Tio2 Flux in GTAW on Stainless Steel (AISI 304l)
... on 304L stainless steel for an optimal parameter and the effect of various process parameters (welding current (I), welding speed(V), active ...
6
Optimization of magneto rheological fluid assisted cylindrical surface finishing parameters for machining AISI 304L austenitic stainless steel
... AISI 304L stainless steel by proper combination of process ...of 304L SS without MR fluid is around 100 nm (average initial value) to 50–120 nm (average final ...
8
finite element based analysis of friction stir welding process using ansys apdl
... Zhu and Chao [28] presented three-dimensional nonlinear thermal and thermo-mechanical simulations using finite element analysis code –WELDSIM on 304L stainless steel friction stir welded plates. ...
10
Study of Fatigue Crack Propagation in the Austenitic Stainless Steel 304L
... B. Effect of stress ratio on the fatigue crack growth rate In order to investigate the cyclic deformation behaviour of 304L stainless steel when it is subjected to mean stresses, numerical ...
7
Anti-corrosion Properties of a Bioinspired superhydrophobic surface on Stainless Steel
... superhydrophobic stainless steel surface with anti-corrosion property was realized in this ...superhydrophobic stainless steel possessed a polarization resistance that is ...common ...
10
Preparation, Characterization and Application of Stainless Steel/Fe, Co, Ni Electrocatalyst Electrodes
... using stainless steel substrate which is coated by Fe, Co, Ni as electro-deposition with linear voltammetric method, afterward it was used as electro-catalyst electrodes in the production of hydrogen gas by ...
10