3D finite element model
Development of a 3D finite element model of lens microcirculation
... working model is that the current, carried primarily by Na + , enters at all locations around the lens via the extracellular space between fibre ...this model, the circulat- ing current creates a net flux ...
27
Moisture-induced stresses in engineered wood flooring with OSB substrate
... The finite element method is a useful tool to predict the behavior of EWF [3, ...(3D) finite element model of the hygromechanical cupping in layered wood composite floor- ...The ...
9
Finite Element Model of Interior Concrete Structures for Seismic Analysis with High-Frequency Content
... (3D) Finite Element Model (FEM) of the reactor building Interior Concrete Structure (ICS) with an emphasis on the dynamic modeling requirements for performing seismic analyses subject to ...
10
Paper 13-2007
... transient 3D finite element model is developed to simulate the functional electrical stimulation of the human upper arm over ...Our model was validated by comparison the computed ...
10
Seismic Response of the ACR(TM) Reactor Building
... stick model that captures both mass and stiffness characteristics of the reactor ...detailed 3D finite element model that captures areas of irregularities and stress concentration is ...
8
Exploring the Impact of Work Life Balance on the Employee and Organisational Growth
... A 3D finite element model was developed for simulation in the electro-thermal environment of COMSOL MULTIPHYSICS 3.5 software with aluminium plate as the test specimen and surface and ...
5
Sensor Placement based on FE Modal Analysis: Dynamic Characteristic of Cable Stayed Penang (I) Bridge
... mathematical model is provided by the Malaysian highway authority as depicted in Figure 3 ...the 3D Finite element model was tuned manually to reduce the errors and discrepancy of ...
7
Analysis and Design of Transverse Post Tensioned Slab K V S Sasidhar Reddy, J Vara Prasad, N Venkata Hussain Reddy
... a 3D finite element model, representing a 45- floors high rise shear Wall structure, is created with the aid of ETABS 2015 ...the finite element analysis and presented in the ...
7
Moment resistance and rotation capacity of semi-rigid composite connections with precast hollowcore slabs
... of 3D finite element model and full scale tests, the analytical method to calculate the moment and rotation capacity of this type of composite joints were ...
23
Evaluation on Fatigue Life of Expressway Asphalt Pavement Based on Tire-Pavement-Subgrade Coupling Model
... as 3D) finite element model of tire-subgrade-pavement structure was established, and the steady-stable rolling of tire and stress-dependent dynamic resilient modulus of subgrade soil were ...
8
Electromagnetic Analysis of Hysteresis Synchronous Motor Based on Complex Permeability Concept
... to model this kind of motor and take into account the magnetic hysteresis characteristic of the rotor hysteresis ...to model the hysteresis loop and the hysteresis loop in inclined ellipse shape is ...using ...
6
Numerical and Experimental Study on Stiffened Composite Panel Repaired by Bolted Joints under Compressive Load
... a 3D finite element model of stiffened composite panels under compressive load was established, and tests were performed on stiffened compo- site panels in virgin or repaired by bolted joints ...
9
Finite Element Analysis of 3D Printed Aircraft Wing
... The 3D printed aluminum wing shows superior fracture/yielding safety factor (1,109% higher), buckling resistance ...of 3D printed model aircraft [10], however there were no calculations to determine ...
11
A Triaxiality-Dependent Constitutive Model For Predicting Damage-Induced Softening in 3D-Printed Soft Suture Layer, Lei Liu
... Chapter 3 focuses on the design/evaluation of the new scarf joint specimens. In Section 3.1, the existing design at the free edge of scarf joint specimens and Arcan specimens are reviewed. In Section 3.2, to investigate ...
243
A MATHEMATICAL MODEL FOR TEMPERATURE DISTRIBUTION IN MULTILAYERED 3D IC’s USING GALERKIN’S FINITE ELEMENT TECHNIQUE
... of 3D circuit design shown in Fig 1 is the problem of increased power density which results in increased temperature of the ...In 3D circuits, in a smaller area large numbers of devices are placed, ...
10
Paper 03-2014-2
... The model consists of the scala vestibuli and scala tympani, separated by the basilar ...simplest model of the cochlea is a box model of the uncoiled ...mechanical model of the cochlea was ...
9
Finite element model of a double-stage helical gear reduction.
... oth model of each gear was chosen because of the fact th a t the contact ratio of this helical gear pair was calculated to be approximately ...partial model would be sufficient for one complete mesh cycle ...
117
Modelling of Patient-Specific Femur with Osteogenesis Imperfecta to Determine the Fracture Risk Under Various Loads
... Abstract— Osteogenesis imperfecta (OI) is a fragile bone disease characterized by easy fractures. The femur consists of cortical and cancellous bone, each with different mechanical properties. Bone fractures often occur ...
9
Composites circular bars based Analysis of Thermal Expansion with Finite Element
... the finite element modelling of these composite materials and tried to gain a better understanding of their ...A 3D model was made using CATIA and finite element, Structural and ...
8
Patterns of stress distribution in different root morphologies on tipping a 3d finite element study
... geometric model in IGES format was imported for creating a finite element model consisting of nodes and elements using discretization ...to finite with the help of MAC ...
9