• No results found

Deposition Temperature

Effects of Deposition Temperature on the Electrochemical Deposition of Zinc Oxide Thin Films from a Chloride Solution

Effects of Deposition Temperature on the Electrochemical Deposition of Zinc Oxide Thin Films from a Chloride Solution

... increasing deposition temperature due to the increase in differences between ZnO thin films and the bare FTO ...a deposition temperature of 70 and 80°C, the resistivity was comparable to ...

7

Deposition Temperature Dependence of Vortex Pinning Property in YBa2Cu3O7+BaHfO3 Films

Deposition Temperature Dependence of Vortex Pinning Property in YBa2Cu3O7+BaHfO3 Films

... nanocomposite film is more complicated, because the nanocomposite structure is formed with complex process comprising diffusion of atoms, nucleation and growth of matrix and second phase, and coalescence of the islands. ...

6

The Effects of Hydrogen Peroxide and Deposition Temperature on the electrodeposited Zinc Oxide Film

The Effects of Hydrogen Peroxide and Deposition Temperature on the electrodeposited Zinc Oxide Film

... as deposition solution. An electro-deposition system with three electrodes, ITO glass as working, platinum as counter and saturated camel electrode as reference, was applied in the deposition ...The ...

9

Effect of the Deposition Temperature on the Corrosion Stability of TiO2 Films Prepared by Metal Organic Chemical Vapor Deposition

Effect of the Deposition Temperature on the Corrosion Stability of TiO2 Films Prepared by Metal Organic Chemical Vapor Deposition

... behavior of the films was assessed through electrochemical impedance spectroscopy (EIS) measurements, potentiodynamic polarization curves and chronoamperometric curves. The tests were performed in a sodium chloride ...

14

Factors Affecting Electroplated Semiconductor Material Properties: The Case Study of Deposition Temperature on Cadmium Telluride

Factors Affecting Electroplated Semiconductor Material Properties: The Case Study of Deposition Temperature on Cadmium Telluride

... It can be recalled from the succinct discussion on the cyclic voltammogram in Section 1.1 and Figure 2, there seems to be continued shift in the graph to the right with decreasing deposition temperature ...

22

Influence of the Deposition Temperature on the Electrodeposition Mechanism of Zn-Co-Fe Alloy

Influence of the Deposition Temperature on the Electrodeposition Mechanism of Zn-Co-Fe Alloy

... the deposition parameters that result in increasing the pH of the zinc–iron metal electrolyte may promote zinc ...zinc deposition potential on the surfaces of iron metals will be higher than that on the ...

15

Synthesis and Analysis of Thin Conducting Pyrolytic Carbon Films

Synthesis and Analysis of Thin Conducting Pyrolytic Carbon Films

... The deposition rate was seen to increase in an exponential fashion with increasing growth temperature as shown in Figure ...the deposition rate against the inverse of the deposition ...

32

Metal Ir coatings on endocardial electrode tips, obtained by MOCVD

Metal Ir coatings on endocardial electrode tips, obtained by MOCVD

... The present work demonstrates the application of the Metal-Organic Chemical Vapor Deposition technique to fabricate metal iridium coatings onto the pole tips of endocardial electrodes. Using iridium (III) ...

24

Fabrication parameters dependent morphology variation of silicon thin film

Fabrication parameters dependent morphology variation of silicon thin film

... as deposition time, temperature and the rate of flow of the precursor gas are controlled to achieve the optimized growth ...The deposition temperature, time and the amount of hydrogen flow ...

7

Molten Salt Pulse Electrodeposition of Silicon on Low Silicon Steel

Molten Salt Pulse Electrodeposition of Silicon on Low Silicon Steel

... A schematic diagram of the electrodeposition experimental device was shown in Fig. 1. The anode, a high purity graphite crucible, served as melt container. The substrate material was used as a cathode. Electrodeposition ...

6

Plasma Assisted Chemical Vapor Deposition of Titanium Oxide Layer at Room Temperature

Plasma Assisted Chemical Vapor Deposition of Titanium Oxide Layer at Room Temperature

... pressure of 3 mtorr by the plasma-cracked precursors and the thermal dissociation of TTIP on the surface. However, the hydrophilic property was degraded with decreasing deposition temperature and not ...

7

Surface Mechanisms in Low-Temperature Plasma Deposition of Silicon

Surface Mechanisms in Low-Temperature Plasma Deposition of Silicon

... low temperature silicon film ...of temperature and precursor flux under steady state growth ...increasing temperature due to an increase in the fractional surface coverage of silicon mono-hydride ...

212

Efficacy of Magnetic and Capacitive Hyperthermia on Hepatocellular Carcinoma

Efficacy of Magnetic and Capacitive Hyperthermia on Hepatocellular Carcinoma

... A (0) . Fig. 3 shows the SAR distribution in the tissues, which ranges from 1 to 8 (watt/kg) in the tumor. Fig. 4 shows the SAR distribution attributed to magnetic nanoparticles. The magnitude of SAR is higher in the ...

12

Effect of Deposition Time and Temperature on the Performance of Electroless Ni-P Coatings

Effect of Deposition Time and Temperature on the Performance of Electroless Ni-P Coatings

... The purpose of this study is to investigate the effects of deposition time and temperature on the surface properties, corrosion and electrolyte resistance of Ni-plated Cu tabs. The surface morphologies and ...

10

Chemical Bath Deposited PbSe Thin Films: Optical and Electrical Transport Properties

Chemical Bath Deposited PbSe Thin Films: Optical and Electrical Transport Properties

... Preparation: Thin films of lead selenide with varying thicknesses were deposited onto ultrasonically cleaned glass substrates using AR grade chemicals. For the deposition, 10 ml (0.33 M) lead sulphate, 4 ml ...

5

Combined apatite fission track and U Pb dating by LA ICPMS and its application in apatite provenance analysis

Combined apatite fission track and U Pb dating by LA ICPMS and its application in apatite provenance analysis

... linear defects are commonly referred to as fission tracks, and are enlarged using a standardized chemical etching process so they can be observed under an optical microscope (Price & Walker 1962). The technique is ...

30

High precision detection of change in intermediate range order of amorphous zirconia-doped tantala thin films due to annealing

High precision detection of change in intermediate range order of amorphous zirconia-doped tantala thin films due to annealing

... ambient temperature during deposition was less than 100°C. Post-deposition annealing of three di↵erent samples was carried out at 300, 600 and 800 C in air for 12 ...

12

Effect of sintering temperature on adhesion of spray-on piezoelectric transducers

Effect of sintering temperature on adhesion of spray-on piezoelectric transducers

... Results indicate that the high-temperature processing con- ditions may alter the surface composition of the metal due to a diffusion of the metal into the ceramic, which results in a surface of the metal that is ...

11

Search | Preprints

Search | Preprints

... chemical deposition. The physical deposition refers to the technologies in which material is released from a source and deposited on a substrate using thermodynamic, electromechanical or mechanical ...

27

Colloidal stability of Pinus radiata wood extractives Part 1: Effect of extractives composition and process variables

Colloidal stability of Pinus radiata wood extractives Part 1: Effect of extractives composition and process variables

... pitch deposition of wood extractives released in thermomechanical pulp of Pinus ...are temperature, soluble calcium, pH, dissolved carbohydrates and wood extractive concentration and ...to deposition ...

13

Show all 10000 documents...

Related subjects