Fe-Co-Cr alloy
Theoretical Predict of Half Metals in Co Cr Fe Al Alloys
... the alloy shows typical metallic behavior for the up-spin states while at the same time being a semiconductor for the down-spin ...the alloy is half-metallic or not, in the following ...
5
STUDY OF COATINGS OBTAINED FROM ALLOY Fe-Mn-C-B-Si-Ni-Cr
... eutectic alloy and other materials for building up wear-resistant coatings makes it possible to increase significantly the resistance of their elements to ...The Fe, Co, Ni, Ti – based alloy ...
5
Laser Cladding of Fe Cr C Alloys on A5052 Aluminum Alloy Using Diode Laser
... aluminum alloy, we proposed a diode laser cladding of iron-based alloy on the surface of an aluminum ...with CO 2 laser, which has been conventionally used for laser ...
7
Laser and GTAW torch processing of Fe-Cr-B coatings on steel : Part I - melt features
... adding Co-based alloy powder, while in the third case, a tool steel substrate was used employing a tool steel ...compares Fe-Cr-B powder on plain carbon steel for both laser and GTAW surface ...
16
Phase Transformation and Properties of Fe Cr Co Alloys with Low Cobalt Content
... The results of the heat flow as a function of temperature for the Fe-10Cr-1Co alloy are shown in Fig. 1. It can be found that there are three distinct endothermic peaks during heating. The first one around ...
5
Effect of Tungsten on Mechanical Properties of High Purity 60 mass%Cr Fe Alloys
... and co-researchers reported that the duc- tility of Cr–Fe alloys containing 50 or 60 mass%Cr was re- markably improved by ...50%Cr–Fe alloy has high strength with high ...
6
Effect of Fe Addition on Microstructures and Mechanical Properties of Ni and C Free Co Cr Mo Alloys
... that Co-Cr-Mo alloys possess excellent wear resistance, corrosion resistance, and biocom- ...When Co-Cr-Mo alloys are solidified from the liquid phase, the cooling rate of the alloy ...
5
Original Article Influence of four heat treatments on the corrosion resistance of magnetic attachment keepers
... ways: Co-Cr alloy casting, Ni-Cr alloy casting, gold alloy casting, and laser welding (Ni-Cr ...ceramic alloy, Co-Cr alloy, and gold noble ...
5
Particle shape anisotropy and its effects in AlNiCo and Fe Cr Co magnet alloys
... an alloy so that in principle, and in practice in many alloys which have a ferromagnetic constituent, such measurements can pinpoint the presence of new phases and provide information on the kinetics of the ...
331
Erosion Wear Mathematical Model for WC-Co Reinforcement Hardness Distribution in Fe-Based Alloy Matrix With Evoluted Algorithms Francisco Casesnoves MSc MD
... The current mathematical models for erosion, corrosion, tribocorrosion and biotribology have become more complicated in current industrial manufacturing because of the number of compounds in the physical-chemical ...
9
Evolution of Solidification Structures in Fe Mn Si Cr Shape Memory Alloy in Centrifugal Casting
... the Fe-28Mn-6Si-5Cr SMA was cast into a steel mould with a stair shaped cross section (step-type of the ...the Fe-28Mn-6Si-5Cr SMA has also been done to compare the macro- (dendrite and equi-axed) and ...
11
Surface Tension and Wettability of Liquid Fe 16 mass%Cr O Alloy with Alumina
... liquid Fe–Cr alloys reported by different investi- gators ...the alloy samples or due to in- accurate experimental techniques or those elements affecting the O, S concentrations ...of ...
8
Corrosion Behavior of Fe-Al Alloy Modified with Cr and Ti in Simulated Physiological Human Media.
... the EDS technique did not reveal precipitates on the surface of this alloy. This observation is consistent with the wide interval of composition (35-50 at.% Al) which contains a FeAl phase with a B2 type crystal ...
15
Effect of Annealing on Magnetostrictive Properties of Fe Co Alloy Thin Films
... with increasing annealing temperature up to 1073 K. The magnetostriction above 1093 K signi fi cantly decreased with the emerging fcc phase in the Fe Co alloy. SEM images showed that the crystal ...
5
Sulfur tolerant, exsolved Fe–Ni alloy nanoparticles for CO oxidation
... and Fe–Ni/p catalysts, in as-prepared state, as well as after tempera- ture dependence catalytic ...and Fe–Ni/p catalysts display similar average particle size, with uniformly distributed particles, ...
8
Influence of the Deposition Temperature on the Electrodeposition Mechanism of Zn-Co-Fe Alloy
... In alloy plating, the co-deposition procedure is influenced by a number of factors, ...metal co-deposition mechanism is determined for various plating conditions, a commendable standard may be ...
15
Hydrogen Storage Characteristics and Corrosion Behavior of V-rich Ti-V-Cr-Fe Alloy
... known to promote the secondary Laves phase [24‒26], which is considered to be a catalyst that facilitates hydrogen absorption/desorption kinetics [27]. The microstructure of the alloy was a primary, light grey ...
10
3 An Auger electron spectroscopic study of surface segregation on Fe Cr, Fe C and Fe Cr C alloys
... Fef.rC alloy probably contained a grain-boundary contribution as it was nearly two orders of magnitude above the main grouping of literature ...FeCr alloy, the rer- It lay very close to the extrapolated ...
236
Structural Characterization of Stress Induced Martensitic Transformation in a Polycrystalline Austenitic Fe Mn Si Cr Alloy
... Thus, it was inferred in the above analysis that grains with large Schmid factors for the fcc-hcp martensitic transforma- tion are preferentially transformed in polycrystalline grains by unidirectional stress. Although ...
6
Effects of Helium on Radiation Behavior in Low Activation Fe Cr Mn Alloys
... The results of void swelling are shown in Fig. 7. The void swellings of Fe–Cr–Mn alloy irradiated by three dif- ferent modes were very low as a whole. In the case of helium injection the void ...
5