Inconel-625
Mechanical Behavior of Inconel 625 at Elevated Temperatures
... The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier (PLC) effect. This phenomenon is usually attributed to the dynamic ...
15
Optimizing the process parameters of AWJM using Taguchi method and ANOVA on Inconel 625
... Extensive studies over optimization of AWJM of grey cast iron, aluminium, composites, steel, hard polymers and tiles reveals that water pressure and abrasive jet traverse speed are the significant factors influencing MRR ...
9
Effect of the Cutting Tool Geometry on the Tool Wear Resistance when Machining Inconel 625
... Inconel 625. For the selected geometries of the cutting inserts and the proposed cutting condi- tions with a cutting depth a p = 0.5 and 1.5 mm, the angle of the main cutting edge was κ r < 45°. Under ...
8
A Study on Effect of Intergranular Corrosion by Heat Input on Inconel 625 Overlay Weld Metal
... Aging heat treatment was conducted to determine the intergranular corrosion resistance of 500A, 570A, and 620A specimens under as-weld conditions. Based on the TTT curve of Inconel 625 alloy given in Fig. ...
11
The effect of coating architecture and defects on the corrosion behaviour of a PVD multilayer Inconel 625/Cr coating
... the Inconel 625 and Cr have preferential growth directions, the high relative intensity of both the Cr{1 1 0} and Inconel 625{1 1 1} planes indicates that the preferential growth of each ...
29
CHARACTERIZATION OF MICRO STRUCTURE AND MECHANICAL PROPERTIES OF INCONEL 625 SHEET OFND:YAG LASERWELDING
... In this research work Inconel 625 of 1.5 mm thickness is used. The base material is cut into 82.5 mm × 25 mm × 1.5 mm on Wire EDM machine. The faying surfaces and neighborhood of all the specimens were ...
9
Tribological Effects of H Bn Nano Cutting Fluid Minimum Quantity Lubrication (Nf Mql) on Machining Inconel 625
... the Inconel 625 stock bar used for turning , schematic layout of experimental setup and devices used to measure various response variables (surface roughness, cutting force and material removal rate) ...
10
Microstructure and Surface Morphology of Inconel 625 Alloy Prepared by Laser Melting Deposition using Abrasive-Assisted Jet Electrochemical Machining
... The LMD shaping process of the Inconel 625 is was performed in three main stages. The melted superalloy powder that absorbed the majority of laser energy, mixed with the micro-melted substrate or the last ...
15
Study on Effect of Welding Speed on Micro Structure and Mechanical Properties of Pulsed Current Micro Plasma Arc Welded Inconel 625 Sheets
... [3] K. S. Prasad, C. S. Rao and D. N. Rao, “Optimizing Pulsed Current Micro Plasma Arc Welding Parameters to Maximize Ultimate Tensile Strength of Inconel 625 Nickel Alloy Using Response Surface Method,” ...
7
Corrosion Resistance of Inconel 625 Overlay Welded Inside Pipes as a Function of Heat Treatment Temperature
... Inconel 625 was initially produced as a solid solution strengthening alloy, but it shows precipitation, intermetallic compounds, and carbide formation at specific temperatures and over ...
11
Comparison of Corrosion Resistance and Corroded Surfaces of Welding Metal in Overlay-Welded Inconel 600 and Inconel 625 by Gas Metal Arc Welding
... hand, Inconel 625 has high oxidation resistance because of its high Cr content and excellent resistance against SCC and intergranular ...of Inconel 625 broadens, more and more studies are ...
14
Optimizing of High Speed Turning Parameters of Inconel 625 (Super Alloy) by using Taguchi Technique
... turning. Inconel 625 is on which optimization experiment can be performed to find out the set of optimum values of process parameters in order to reduce surface roughness (SR) and increase material removal ...
7
Study of the pitting corrosion at welding joints of Inconel 625 alloy under high temperature and high H2S/CO2 partial pressure
... of Inconel 625 weld is directly affected by the alloy microstructure ...of Inconel 625 weld is equivalent to that of base metal ...in Inconel 625 welds is reported to be ...
15
Effect of Heat Treatment Temperatures on Microstructure and Corrosion Properties of Inconel 625 Weld Overlay Deposited by PTIG
... Fronius automatic PTIG welding system was used to clad Inconel 625 on the substrate. The optimized essential welding parameters used to deposit the cladding are listed in Table 2. The diameters of the jet ...
13
Electrochemical Behavior of Corrosion Resistance of X65/Inconel 625 Welded Joints
... on Inconel 625 is a mixed Fe-Cr oxide; and protects the material from further ...wrought Inconel 625 to exhibit passivation at remarkably low current density values during polarization tests ...
11
Experimental and Finite Element Simulation in Turning Inconel 625 with CNMG Carbide Insert
... Quality of a product can be described by various quality attributes. The attributes may be quantitative or qualitative. In on-line quality control controller and related equipments are provided with the job under ...
10
Investigation of the Weld Properties of Inconel 625 based on Nb Content
... solidification process and the larger Cr depletion region compared to the other specimens. The No.1 specimen contains 2% Nb, which is lower than the typical Nb content of Inconel 625 (3.15~4.15 wt%). Since ...
13
Experimental Optimization of Process Parameters with Wire EDM on Inconel 625
... Inconel 625 is superalloy of nickel and chromium which is mainly used in marine, petroleum, chemical industries due to its superiority mechanical, chemical and thermal properties ...
8
Microstructural evolution of Inconel 625 and Inconel 686CPT weld metal for clad carbon steel linepipe joints : a comparator study
... in Inconel 686CPT weld metal, the segregation of tungsten is a function of the level of iron dilution from the parent ...the Inconel 686CPT weld metal has a morphology that is dependent on tungsten ...
46
The influence of the post weld heat treatment on the microstructure of Inconel 625/carbon steel bimetal joint obtained by explosive welding Robert Kosturek 1, Marcin Wachowski 1, , Lucjan Śnieżek 1, Michał Gloc2
... of Inconel 625 – steel P355NH joint obtained by explosive welding decreases its shear strength by 33% (decrease from 572 MPa to 383 MPa, determined according to PN-EN13445:2014) ...Additionally, ...
15