• No results found

mechanical tests

Applicability of mechanical tests for biomass pellet characterisation for bioenergy applications

Applicability of mechanical tests for biomass pellet characterisation for bioenergy applications

... of mechanical tests for biomass pellet characterisation was ...rate) mechanical tests were applied to mixed wood, eucalyptus, sunflower, miscanthus, and steam exploded and microwaved pellets, ...

18

Conduct of Mechanical Tests Simulating the Accidental Action of External Mechanical Factors

Conduct of Mechanical Tests Simulating the Accidental Action of External Mechanical Factors

... These tests were conducted on the Instron 4303 testing machine. The universal traction, compression and buckling testing machine Instron 4303 is a universal testing tool shown in Figure 16. The machine has a ...

8

An assessment of the compaction behaviour of pharmaceutical compacts by means of complementary mechanical tests

An assessment of the compaction behaviour of pharmaceutical compacts by means of complementary mechanical tests

... 55 loading and stress distributions were not completely defined. The new diametral compression test had less variance and was not affected by surface conditions or inherent effects as is the case for bending ...

295

A Study of the Electrochemical Performance of Strip Supercapacitors under Static and Dynamic Mechanical Tests

A Study of the Electrochemical Performance of Strip Supercapacitors under Static and Dynamic Mechanical Tests

... Mechanical tensile stress tests were performed with an Instron machine (Model 2580- 106/105924). The length between the two grips, where the tensile loading was applied, is 80 mm. The configuration of the ...

11

PLC based CB Endurance Controller

PLC based CB Endurance Controller

... the mechanical tests. However, lubrication is After the tests, the contacts, linkages and all the other parts should be in good condition and should not show any permanent deformation or ...the ...

6

Influence of clay properties on shoe-kinematics and friction during tennis movements

Influence of clay properties on shoe-kinematics and friction during tennis movements

... of mechanical tests were conducted with three different devices on the two different clay surfaces prepared: the pendulum test (British Standard), Crab III test and a bespoke sled friction test device were ...

6

Real time sensing of structural glass fiber reinforced composites by using embedded PVA - carbon nanotube fibers

Real time sensing of structural glass fiber reinforced composites by using embedded PVA - carbon nanotube fibers

... different mechanical tests were conducted and the potential for electrical conductivity measurements for structural health monitoring was evaluated: (a) progressive damage accumulation (PDA) tests on ...

8

Abstract study and validation of a device of tests of quality control of the mechanical characteristics of tiles in micro concrete

Abstract study and validation of a device of tests of quality control of the mechanical characteristics of tiles in micro concrete

... load and the device that holds the tile are not met. Having regard to all the foregoing, we have developed in the laboratory of applied mechanics and energy (LEMA), a new test which includes three control tests. ...

8

Suitability of Vermiculite and Rice Husk Ash as Raw Materials for Production of Ceramic Tiles

Suitability of Vermiculite and Rice Husk Ash as Raw Materials for Production of Ceramic Tiles

... soaking time, at a heating rate of 50°C per minute in a Carbolite box furnace (RHF 14/8 Model) manufactured by Keison products Inc, UK. The firing parameters tests were all performed at Tanzania Portland Cement ...

10

The quality of orthodontic wires of nickel titanium: a short review

The quality of orthodontic wires of nickel titanium: a short review

... good mechanical properties (Quintão and Brunharo, 2009). Mechanical tests are effective in determining the properties of orthodontic wires of various brands, however, such methods do not reflect the ...

5

Re-examination of the mechanical anisotropy of porcine thoracic aorta by uniaxial tensile tests

Re-examination of the mechanical anisotropy of porcine thoracic aorta by uniaxial tensile tests

... the mechanical tests. In the tests, the engineering stress σ and strain ε were calculated by σ = F/A and ε = Δl/l, respectively, where F is the tension force, A is the initial cross-sectional area ...

14

A combination of SEM and EDX studies on a clay-based natural composite with animal fibre and its mechanical implications

A combination of SEM and EDX studies on a clay-based natural composite with animal fibre and its mechanical implications

... A variety of natural fibres are nowadays being utilized as soil reinforcement. Test results demonstrate the positive effects of adding natural fibres to soils, in that they decrease shrinkage, reduce curing time and ...

8

Evaluation of antinociceptive activity of nanoliposome-encapsulated and free-form diclofenac in rats and mice

Evaluation of antinociceptive activity of nanoliposome-encapsulated and free-form diclofenac in rats and mice

... of mechanical hyperalgesia compared with the control group (Figure ...carrageenan-induced mechanical hyperalgesia at various experimental time points compared with its nonencapsulated form at all equivalent ...

7

Response of UHPFRCs in Tension under High Stress Rate

Response of UHPFRCs in Tension under High Stress Rate

... The mechanical response of UHPFRC under high loading rate in tension can be considered linear-elastic up to matrix tensile strength localized in the notch is reached (see ...these tests the damage is forced ...

6

A Study on the Effect of Fly Ash on Hybrid Fibre Reinforced Concrete A Paul Makesh1, Vellingiri Anusuya 2

A Study on the Effect of Fly Ash on Hybrid Fibre Reinforced Concrete A Paul Makesh1, Vellingiri Anusuya 2

... The compressive strength test is carried out as per IS 516 – 1968. The specimens of size 150mm cube are caste with volume fraction of 0.5 and 1.0 % with two types of fibre. The test is carried out for 28 days and test ...

9

Application of Taguchi approach to optimize friction stir welding parameters of polyethylene

Application of Taguchi approach to optimize friction stir welding parameters of polyethylene

... tensile tests performed on tensile specimens having a weld cordon width of 14mm situated in the central zone of the active ...the mechanical properties of the base material are much lower than those of the ...

8

Strength Behaviour of Recycled Concrete with Partial Replacement of Conventional Aggregate

Strength Behaviour of Recycled Concrete with Partial Replacement of Conventional Aggregate

... Specimen test: The compressive and tensile strength for each types of concrete were determined using Universal Testing Machine. The compression test is carried out to determine the characteristic strength of the ...

7

Simulation of a Single  Motor of Latch Type Control Element Drive Mechanism for Korean Next Generation  Reactor

Simulation of a Single Motor of Latch Type Control Element Drive Mechanism for Korean Next Generation Reactor

... motor coil from tests give valuable information of the latch mechanical motion and the amount of force necessary to the.. system operation.[r] ...

8

Shearing with Infiltration Tests to Study Mechanical Behavior and Failure Mechanism of Shallow Slopes

Shearing with Infiltration Tests to Study Mechanical Behavior and Failure Mechanism of Shallow Slopes

... stress, after which matric suction was decreased by increasing pore water pressure to start water.. 17.[r] ...

13

Text
BC final IC STAR2015 pdf

Text BC final IC STAR2015 pdf

... and mechanical properties resemble wih conventional plastics LDPE (Low Density ...of mechanical strength on a sheet of bioplastics due to various factors, including the addition of a different filler ratio ...

7

Show all 10000 documents...

Related subjects