Orthogonal cutting
Deformation State of Aluminum-6% Silicon Alloy (319 Al) Subjected to Orthogonal Cutting at Different Speeds and Feed Rates
... in orthogonal cutting influences the primary deformation, built-up edge formation, cutting temperatures, tool wear, etc and hence it is important to analyze it in order to better understand the ...
320
Influence of Water Cooling on Orthogonal Cutting Process of Ti-6Al-4V Using Smooth-Particle Hydrodynamics Method
... of orthogonal cutting process increases by entering cutting tool then converges to constant value as the process remains at steady ...non-cooling orthogonal process are higher than process ...
8
Investigation of formation mechanisms of chips in orthogonal cutting process
... in orthogonal cutting of mild steel and the transformation conditions between various morphology ...In orthogonal cutting process, both the plastic flow and the instability behaviors of chip ...
6
Residual strain analysis with digital image correlation method for subsurface damage evaluation of hinoki (Chamaecyparis obtusa) finished by slow-speed orthogonal cutting
... slow-speed orthogonal cutting of hinoki (Chamaecyparis obtusa), to evaluate the damage in the subsurface cell ...the cutting direction was detected for the depth of cut and cutting angles, ...
10
Strain analysis near the cutting edge in orthogonal cutting of hinoki (Chamaecyparis obtusa) using a digital image correlation method
... Instead of using those methods, we decided to utilize a digital image correlation (DIC) method [13–17], a non- contact strain measurement technique that is becoming popular in the study of wood and wood-based materials ...
12
Determination of the Deformation State of a Ti-6Al-4V Alloy Subjected to Orthogonal Cutting Using Experimental and Numerical Methods
... During orthogonal cutting, cutting and thrust forces are two important forces exerted by tool on the ...measuring cutting and thrust ...
267
Evaluation of the Minimum Quantity Lubrication in Orthogonal Cutting with the Application of Finite Element Method
... in cutting, it is necessary to understand the tribological and thermal effects of MQL during cutting ...of cutting force and cutting temperature. In the meantime, orthogonal ...
6
Estimation of Tool Wear Rate in Orthogonal Cutting Using Experimental and Statistical Approach Sonawane Swapnil Vijay
... in orthogonal cutting based on experimental data and statistical ...metal cutting tool wear is strongly influenced by cutting forces, speed, feed, and depth of ...and cutting forces ...
7
Observation of machined surface and subsurface structure of hinoki (Chamaecyparis obtusa) produced in slow-speed orthogonal cutting using X-ray computed tomography
... resultant cutting force [15, 16], although the relation between the types and surface quality is not deeply discussed in these ...and orthogonal cutting, and found that changes in the occur- rence of ...
8
Orthogonal cutting mechanics of maple: modeling a solid wood-cutting process
... of orthogonal cutting of maple and the modeling of the cutting mechanics are pre- ...tool cutting forces were measured for different feed ...edge cutting force coeffi- cients was ...
7
Effect of grain angle on the strain distribution during orthogonal cutting of hinoki (Chamaecyparis obtusa) measured using a digital image correlation method
... with orthogonal cutting with and against the grain of hinoki (Chamaecyparis obtusa) was ...the cutting direction was detected in the area above the path of the cutting edge regardless of ϕ ...
11
Finite Element Analysis of Orthogonal Cutting Forces in Machining AISI 1020 Steel Using a Carbide Tip Tool | Journal of Engineering Sciences
... model orthogonal cutting processes. An ALE model for orthogonal cutting of AISI 4340 with cemented carbide tools was developed by Llanos et ...and cutting forces were predicted with ...
10
A Model for Predicting Dynamic Cutting Forces in Sand Mould Milling with Orthogonal Cutting
... the cutting force directly affects the machining quality and tool ...of cutting force is proposed based on the unequal division shear zone model of orthogonal ...the orthogonal cutting ...
11
Machining induced damage in orthogonal cutting of UD composites : FEA based assessment of Hashin and Puck criteria
... This article focusses on the 2D FE simulation of orthogo- nal cutting of composites taking into account effect of various fibre orientations and change of cutter geometry. Two numeri- cal algorithms - Hashin-Rotem ...
7
Influence of anisotropy of additively manufactured AlSi10Mg parts on chip formation during orthogonal cutting
... specific cutting force shown in Figure 7 a) is within a 20% error corridor for most experiments, when anisotropy is ...the cutting force is underestimated by a little more than 20% for the 45° variant, and ...
6
Experimental studies and numerical simulations of continuous and discontinuous chip formation during orthogonal cutting.
... the cutting line and decreased with increasing distance from the cutting line until below a certain depth, where it became close to the yield strength o f the ...
217
Experimental Analysis of Cutting Forces and Temperature in Orthogonal Machining of AISI 1045 Steel
... the cutting forces and the temperature during the orthogonal cutting of AISI 1045 steel using a tungsten carbide ...by cutting speed, feed rate and tool ...of cutting forces and ...
7
An Investigation into Orthogonal and Oblique Cutting Processes
... The cutting process was originally defined as orthogonal cutting in which a piece of material is separated by applying enough force to cause material to fail but orthogonal cutting is ...
155
Survey on Nano Cutting Fluids in Metal Cutting Application
... the cutting edge wear occurs rapidly, because of the absence of cutting ...conventional cutting fluid, the cutting fluid presence protects the edge of the cutting tool partially due to ...
5
Cutting-Tool Wear during High-Speed Cutting
... by cutting is strongly connected with wear on the tools edge. The cutting-tool materials, the machined material, and the machining parameters have a direct influence on the tools wear grade and, of ...
11