polyamide-6
Zinc stannate interactions with flame retardants in polyamides; Part 2: Potential synergies with non-halogen-containing flame retardants in polyamide 6 (PA6)
... Zinc stannate is a well known synergist and smoke suppressant with brominated flame retardants in a number of polymers but its possible synergistic function with phosphorus- containing species is less well documented. ...
25
Mechanical, thermal and physical properties of chitosan and chitin filled compatibilized polyamide-6/polypropylene composites
... Wahit, M.U., Lim, J.W., Hassan, A. and Mohd Ishak, Z.A. (2004). Polyamide 6/ Polypropylene Blends Nanocomposites : The Effect of Blend Ratio on the Mechanical Properties. 1st National Postgraduate ...
30
Statistical Optimization of the Sol–Gel Electrospinning Process Conditions for Preparation of Polyamide 6/66 Nanofiber Bundles
... Some other researches, related to the electrospinning process, adapted it to a coagulation bath and tensile cyl- inders to develop the electrospinning sol–gel process (see Fig. 1). With the latter, polyvinyl alcohol ...
7
Modification of organo-montmorillonite with disodium H-phosphonate to develop flame retarded polyamide 6 nanocomposites
... (DHP/PA6) decreased PHRR value by about 14%, compared to the PA6. Curves of HRR versus time for DHP/PA6 and Mt-DHP/PA6 samples exhibit two peaks assigned to the development of intumescenct char. The first corresponds to ...
39
Multi-jet electrospinning of polystyrene/polyamide 6 blend: thermal and mechanical properties
... Polystyrene (PS) has high thermal resistance thus can be applied as thermally comfort- able textile. However, the application is limited due its low mechanical strength. In this study, polyamide 6 (PA6) was ...
12
Numerical Simulation of Mechanical Properties of Nano Particle Modified Polyamide 6 via RVE Modeling
... In this paper the mechanical behavior of a Polyamide 6 (PA 6)/Montmorillonit (MMT)-nanocom- posite is examined by a selected structure modification within a numerical parameter study. Ex- perimental ...
8
The Effect of Curative Concentration on Thermal and Mechanical Properties of Flexible Epoxy Coated Jute Fabric Reinforced Polyamide 6 Composites
... Many researchers have shown interest in the reinforcement of commodity thermoplastic with natural fibers. However, the drawback of natural fibers is their low thermal processing temperatures, that border around 200˚C. In ...
6
Study of fluid structure of polyamide 6 with polar/apolar solvents using dielectric parameters
... [1]. Polyamide-6 (PA 6) is widely used in manufacturing of gears, fittings, bearings, electrical switches, bobbins, and connectors, power tool housings, wheelchair wheels and automotive cooling fans ...
9
The Antibacterial Polyamide 6 ZnO Hierarchical Nanofibers Fabricated by Atomic Layer Deposition and Hydrothermal Growth
... electrospun polyamide 6 (PA 6) nanofiber (NF) surface in the purpose of antibacterial ...ZnO/PA 6 core-shell composite fabricated by the combination of ALD with hydrothermal are markedly ...
8
Synthesis of Polyamide-6/Montmorillonite Nanocomposites by Direct In-situ Polymerization Catalysed by Exchanged Clay
... obtain polyamide-6 nanocomposites with national organically modified clay (termed ...of polyamide-6 was confirmed by infrared spectroscopy (IR), the prepared nanocomposites were characterized ...
8
Degradation of Glass Fiber Reinforced Polyamide 6 Composites Throughout the Direct Long-Fiber Reinforced Thermoplastic Process
... plastics. Polyamide 6 (PA6) is a good candidate as a polymer matrix in the D- LFT process because it has high toughness over a large range of temperature, good impact and abrasion resistance, lubricity, and ...
95
Characterization of unidirectional carbon fiber reinforced polyamide-6 thermoplastic composite under longitudinal compression loading at high strain rate
... PA6 CF60-01, a 60% carbon fiber by weight polyamide- 6 unidirectional reinforced thermoplastic composite tape [15]. According to the material data sheet [15] a fiber volume content of 48% is then obtained. ...
6
Acoustic Emission Analysis of Dissimilar Laser welds of Aluminium and Polyamide 6 6
... Abstract A novel laser joining process for hybrid polymer-metal structures has proven a strong bond between polyamide and aluminium. This welding technique is strongly requested by the automobile producing ...
6
Modeling and Simulation of Mechanical Properties of Nano Particle Modified Polyamide 6
... This paper discusses the utilization of nano-sized fillers in Polyamide 6 to increase the fracture resistance of the composites, which are crucial for various engineering applications. The tough- ening of ...
8
Extraction of KHCO 3from Microporous Polyamide 6 and Single
... Experimental Procedure: Microporous polyamide 6-pellets were used a porous material. This material is an inert and plastic material in the pellet form that provides a suitable porous carrier for the ...
6
Rheological behavior of polyamide-6/linear low density polyethylene grafted maleic anhydride/monmorillonite nanocomposites and statistical model
... Polyamide 6 (PA6) with different linear low density polyethylene grafted maleic anhydride (LDPE-g-MAH) and montmorillonite (MMT) loadings were produced by melt compounding using single screw ...
25
Interactions between Nanoclays and Flame Retardant Additives in Polyamide 6 and Polyamide 6.6 Films
... Figure 1 shows that the bimodal structure of the fusion endotherm for the pure polyamide 6.6 film, presumably the α-form, changes to a single peak when the nanoclay is present. The change in shape is indicative of ...
36
Study on the mechanical behavior of directly compounded long glass fiber reinforced polyamide 6 composites
... SEM images taken on the fracture surfaces of tensile D-LFT specimens with 20 and 50 wt.% fiber tested in 0-direction are shown in Figure 4-6. Large amounts of holes in the matrix indicate that the fiber pull out ...
120
Maleic anhydride polyethylene octene elastomer toughened polyamide 6/polypropylene nanocomposites: mechanical and morphological properties
... The redBctioa of flexlllal stength and odulus was abol$ 50% and 620/0 fot 6e PA6PP (70:30) bleld respectivelv However, iDterestingly the addition of organoclay into POBg toughen[r] ...
10
Color masterbatches for polyamide 6 fibers. Optimization of compounding and spinning processes. Physical-chemical characterization of industrial products.
... Generally speaking, PA6 shows excellent resistance to fatigue, impact, good toughness and low friction coefficient. Moreover PA6 has good chemical resistance against many fuels, oils and it is inert to biological attack ...
194