Post-Tensioned Metal Straps
Seismic retrofitting of RC buildings using CFRP and post tensioned metal straps : shake table tests
... This article examines the effectiveness of two innovative retrofitting solutions at enhancing the seismic behaviour of a substandard reinforced concrete building tested on a shake table as part of the Pan-European funded ...
37
Seismic Retrofitting of RC Buildings Using CFRP and Post-Tensioned Metal Straps: Shake Table Tests
... This article examines the effectiveness of two innovative retrofitting solutions at enhancing the seismic behaviour of a substandard reinforced concrete building tested on a shake table as part of the Pan-European funded ...
37
Seismic retrofitting of RC buildings using CFRP and post tensioned metal straps: shake table tests
... This article examines the effectiveness of two innovative retrofitting solutions at enhancing the seismic behaviour of a substandard reinforced concrete building tested on a shake table as part of the Pan-European funded ...
36
Full Scale Shaking Table Tests on a Substandard RC Building Repaired and Strengthened with Post Tensioned Metal Straps
... using Post-Tensioned Metal Strapping ...the post-tensioning of high-strength steel straps (bands) around RC members using hydraulically-operated steel strapping tools similar to those ...
45
Full scale shaking table tests on a substandard RC building repaired and strengthened with post tensioned metal straps
... All straps were fastened using “push type" seals of 25 mm length (see seals in ...the metal strapping provided a confining grid around the beam-column joints and columns ...and metal ...
46
Strengthening of short splices in RC beams using Post-Tensioned Metal Straps
... The test results of this study suggest that the PTMS confinement can be as effective as other techniques currently used in practical strengthening solutions. For instance, the average lap bond strength enhancement ...
29
Strengthening of short splices in RC beams using Post-Tensioned Metal Straps
... novel Post-Tensioning Metal Strapping (PTMS) technique for strengthening RC beams and ...the post-tensioning of ductile metal straps around RC elements using pneumatic steel strapping ...
29
Strengthening of short splices in RC beams using Post-Tensioned Metal Straps
... novel Post-Tensioning Metal Strapping (PTMS) technique for strengthening RC beams and ...the post-tensioning of ductile metal straps around RC elements using pneumatic steel strapping ...
29
Full-scale shaking table tests on a substandard RC building repaired and strengthened with post-tensioned metal straps
... using Post-Tensioned Metal Strapping ...the post-tensioning of high-strength steel straps (bands) around RC members using hydraulically-operated steel strapping tools similar to those ...
46
Elastic Design of Slender High-Strength RC Circular Columns Confined with External Tensioned Steel Straps
... fib (2013). “ Model Code for Concrete Structures 2010 ”, 1st Ed. Berlin, Germany: Ernst & Sohn GmbH & Co. Garcia, R., Hajirasouliha, I., Guadagnini, M., Helal, Y., Jemaa, Y., Pilakoutas, K., et al. (2014). “Full ...
32
Analysis and Design of Post Tention Concrete Slabs
... on post- tensioned flat plates, bonded or unbonded, may be analyzed as for rigid frames in accordance with the provisions of the code ( IS, ACI ...by post-tensioning has a more gentle ...
9
Recent Advances in the Straps/Strips Technique for Out-of- plane Strengthening of Load-bearing Masonry Walls
... the straps/strips technique with straps made either with steel ribbons or with steel wire ropes: the masonry wall failed with a disconnection at the interface between mortar and bricks, as usual in ...
14
BEYOND DESIGN CONSIDERATIONS FOR BONDED AND UN-BONDED TENDONS IN NUCLEAR CONTAINMENTS
... The objective of this paper is to assess the pressure capacity of the containment in the ultimate limit state at which the structural integrity is retained. For estimating the pressure capacity of the containment ...
9
Post-Tensioned Clay Brick Masonry Walls for Modular Housing in Seismic Regions
... unbonded post-tensioning steel enters into the inelastic range thus resulting in residual deformation in the bar upon reversal which produces a loss of ...the post-tensioning bars during the tests were ...
212
Optimization of Precast Post tensioned Concrete I Girder Bridge
... After the mathematical formulation of optimization problem, design program is developed and tested. Next step is to test the optimizer and connect the design program to optimizer. In this problem detailed study on ...
7
A Study on Post Tensioned T Beams Strengthened with AFRP Fabric
... Aramid Fiber as an external reinforcement is used extensively to deal with the strength requirements related to flexure in structural systems. The manufacturing unit of good quality of fibers is Kevlar. The modulus of ...
6
Case study to determine the camber of post- tensioned 'I' beam
... The scope of this study will be focused on full scale 36m long post-tensioned “I” beam with overall height of 1.98m.( Figure 1.2 ) Field data for actual beam camber will be measured base on differences of ...
23
Performance Evaluation of Post Tensioned Concrete Beams with Bonded System
... the post-tension stress applied to each beam. Therefore it concludes that increase in cracking load is achieved by increasing the stress level.The maximum loads of specimens Beam 1 and Beam 4 were higher than the ...
5
A Review on Seismic Assessment of Post-Tensioned Flat Slab
... analyzed post-tensioned concrete slab-column frame buildings by pushover ...general post-tensioned concrete slab-column frame buildings possess relatively low lateral stiffness, low lateral ...
5
Effect of Prestressing Force, Cable Profile and Eccentricity on Post Tensioned Beam
... of post-tensioned beams. The nonlinear flexural behavior of post-tensioned concrete beams, a 3-D finite element model was developed using ...four post- tensioned beams were ...
7