push-out
Online Scheduling FIFO Policies with Admission and Push-Out
... pushed out from the queue after being admitted due to admission control pol- icy considerations (if push-out is allowed), the packet is lost without gain to the algorithm’s ...
22
Experimental study and analytical study of push-out shear tests in Ultra Shallow Floor Beams
... As the floors are being cast, the in-situ concrete passes through the web openings, which may or may not include a tie-bar or duct. This concrete plug and tie bar forms a unique mechanism for transferring longitudinal ...
9
Analysis of failure behavior of shear connection in push-out specimen by three-dimensional stress analysis
... the analysis of the shear composite behavior of real composite beams and those of standard push-out test. To that goal, the stress computed by three-dimensional FEA of the push-out specimen ...
9
The Effect of Different Irrigation Regiments on the Push out Bond Strength of MTA Fillapex Sealer to Dentin
... The adhesive properties of endodontic sealers are important as gutta-percha does not bond to root dentin and is used in conjunction with a root canal sealer. The risk of filling detachment from dentin during restorative ...
8
Effect of various factors on the push out bond strength of mta based root canal sealers - a systematic review
... and push-out ...and push-out ...contrary, push-out bond strength test eliminates this shortcoming of microtensile test, and has thus gained popularity for determining the bond ...
6
Comparative evaluation of push-out bond strength of two different root end repair material
... Melek Akman et al., in 2015 evaluated the effect of intra-canal medicaments on push-out bond strength of Biodentine and DiaRoot Bioaggregate when used as apical plug. Combination of Metronidazole- ...
105
The Effect of Swain's Push Out Hypothesis on Promoting Jordanian Language Learners' Reading Performance
... Moreover, it is believed that few teachers look at the push out hypothesis as a great facilitator to enhance reading com- prehension, which also leads to improve the knowledge of English grammar. ...
13
Influence of aging methods on push-out bond strength of adhesive systems to dentin cavities
... Although the use of sodium hypochlorite has already been proposed to promote bond degradation in dentin cavities [7], thermal cycling (TC) and mechanical loading (ML) are methods commonly used to promote bond degradation ...
7
Effect of Layering Technique on Push-Out Bond Strength of Composite Resin to Intracanal Dentin of Primary Anterior Teeth
... a push-out model. The push-out test results in a shear stress at the dentin-bonding agent interface as well as the bonding agent-composite resin interface, which is more comparable with ...
9
Effect of the of Zeolite Containing Silver-Zinc Nanoparticles on the Push out Bond Strength of Mineral Trioxide Aggregate in Simulated Furcation Perforation
... The samples were subjected to a push-out test with the use of a universal testing machine (H5K-S; Hounsfield Test Equipment, Surrey, England). A force was inserted to the restorative materials in the ...
5
Effect of Etching Time and Preparation on Push-Out Bond Strength of Composite to Intracanal Dentin of Primary Anterior Teeth
... of push-out test, samples were examined under a light microscope at x40 magnification (SZX2-zb16; Olympus, Tokyo, Japan) to determine the mode of ...the push- out bond strength was evaluated ...
8
Push-out tests and analytical study of shear transfer mechanisms in composite shallow cellular floor beams
... All test specimens consisted of a steel section and concrete slab flush with the steel flanges, as depicted in Fig. 4. Three web openings were fabricated on the web post of the steel section. The in-situ concrete passed ...
43
Effect of Intracanal Post Space Treatments on Push-Out Bond Strength of Fiber Posts to Root Dentin
... positioned at the center of each post, while avoiding contact with the peripheral dentin and the force was applied in apico-coronal direction [15]. Load was applied at a crosshead speed of 0.5 mm/minute in a universal ...
7
Push Out Tests of Cold Formed Steel and Concrete Slab
... In the other specimens with shear dowel enhancement (P2, P3 and P4), failure was started by concrete crushing followed by splitting of the concrete slabs as shown figures (13), (14) and (15). This phenomenon referred ...
10
The push out bond strength of polydimethylsiloxane endodontic sealers to dentin
... better push out bond strength than GF 2 but still less stronger than AH ...higher push out bond strength [39, ...fill out the voids and improve the sealing ability ...
6
The push-out bond strength of calcium silicate-based endodontic sealers
... sealer. Within the limitations of the POBS investigation, the bond of the sealer either to the root canal wall or to the core material is assessed with the interaction of a sealer with root dentin being an ...
7
Testing and Numerical Modelling of Steel-Concrete-Steel with Stud Bolts Connectors Subject to Push-Out Loading
... simulation of concrete-connector interaction. In any case, shear connectors in the models introduced in earlier research are dissimilar from stud bolt modeling. Thus, a 3D finite element model is developed by ABAQUS CAE ...
20
Push-Out Tests for a Novel Prefabricated Steel-Concrete Composite Shallow Flooring System
... full-scale push-out tests aimed at investigating the longitudinal shear behaviour of these novel flooring systems and the effects of additional shear ...carried out to investigate the failure ...
6
The Effect of Various Mixing Techniques on the Push-Out Bond Strength of Calcium Enriched Mixture
... The results of the current study showed that there was no significant difference between the push out bond strength of similar groups in 3 and 21 days. This finding is in contrast with that of Rahimi et al. ...
6
Effect of cementation protocol on push-out bond strength of fiber posts to root canal
... conversion in the absence of light activation [9]. During the fiber post cementation into a root canal, only the exposed marginal areas of cement are directly irradiated by the light-curing unit. To compensate for this ...
6