shear tests
Estimation of shear moduli of wood by quasi-simple shear tests
... quasi-simple shear test, which is the most direct method for examining the shear properties of sheet metals, has been applied to measure the shear moduli of ...sized shear re- gions was used ...
6
Evaluating rolling shear strength properties of cross-laminated timber by short-span bending tests and modified planar shear tests
... rolling shear (RS) strength properties of non-edge-glued cross-laminated timber (CLT) made out of New Zealand Radiata pine (Pinus radiata) structural ...bending tests were used to introduce high RS stresses ...
7
Shear tests of double shear plate connector joints in sugi—Japanese larch composite glulam beams
... Shear tests were conducted on the specimen using two types of composite glulam beam, and two types of timber joint (post–beam and girder–beam). The strength proper- ties of the joints were compared with ...
7
Shear Tests for Ultra-High Performance Fiber Reinforced Concrete (UHPFRC) Beams with Shear Reinforcement
... the shear reinforcement in the ultra-high performance fiber reinforced concrete (UHPFRC) ...the shear behavior of UHPFRC rectangular cross sectional beams with fiber volume fraction of ...of shear ...
12
Cyclic and Post-Cyclic Response of Silt and Sandy Silt Soils
... undrained shear strength properties of liquefied soils for post-liquefaction stability analysis have become an important aspect of liquefaction assessment besides the evaluation of conditions that would trigger ...
182
Experimental Study on the Ultimate Shear Performance of Elastomeric Bearings of Doublefold Elastomeric Layer
... Ultimate shear tests were carried out on 2 specimens in order to examine the shear behavior of the elastomeric bearing at ultimate ...Ultimate shear test provoked shear deformation ...
5
The impact of particle shape on the angle of internal friction and the implications for sediment dynamics at a steep, mixed sand–gravel beach
... The shear tests could theoretically be performed without load, loading plate and top porous plate, but then measure- ments of vertical displacement would be ...chosen shear rate. The speci- men ...
12
Study on Steel Plate Reinforced Concrete Bearing Wall for Nuclear Power Plants Part2; Analytical Method to Evalute Response of SC Walls
... Study on Concrete Filled Steel Structure for Nuclear Power Plants (Part 4 Evaluation of Bending Shear Tests), Proceedings Annual meeting of Arch. Compression and shear [r] ...
8
Biaxial shear behaviour of HDNR with Mullins effect and deformation-induced anisotropy
... previous tests, the maximum stresses observed in the – x and –y directions (points C and D of Figure 10b) are similar to the maximum value of ...the shear stress-strain diagram in the two orthogonal ...
22
PubMedCentral-PMC5435125.pdf
... triaxial shear and uniaxial tensile testing with a focus on the ...triaxial shear tests in different orientations regarding the aorta's orthotropic microstructure, and from uniaxial tensile ...
23
Torque loading tests on the rolling shear strength of cross-laminated timber
... planar shear test) to evaluate shear properties of wood products ...encourage shear failure mechanism; in the planar shear test, shear loads are applied by two metal plates face-glued ...
9
Defect formation during preforming of a bi axial non crimp fabric with a pillar stitch pattern
... negative shear, as the shear resistance is derived from in-plane friction between yarns and lateral yarn ...absolute shear angles in the negative shear region are less than 60 for all ...
31
Shear-Bending Buckling Tests of Relatively-Thin Walled Cylindrical Shells
... Static buckling tests of relatively-thin-walled cylindrical shells were performed to prepare the backgrounds for seismic buckling design guidelines of FBR main vessels. Models made of S[r] ...
7
Plastic anisotropy of soft reconstituted clays
... Some typical properties of the three clays are presented in Table 2, corresponding to both their natural and reconsti- tuted states. There is significant variation in the basic prop- erties, which is typical of Finnish ...
15
Stablization of Soil By use of Geo Jute as Soil Stabilizer
... In many engineering problems such as design of foundation, retaining walls, slab bridges, pipes, sheet piling, the value of the angle of internal friction and cohesion of the soil involved are required for the design. ...
12
Shear viscosity and nonlinear behaviour of whole blood under large amplitude oscillatory shear
... and shear rate dependent rheological behavior of blood [20], but alternative rheological techniques have also been ...of shear rates (1–1500 s − 1 ) for rapid and reproducible blood viscosity ...
14
Experimental Investigation for Determination of Strength of FRP-BUTT Joint
... S. Murakami et al [3] :- A unique experimental method is presented in this paper, in which, and adhesive bonded cylindrical but joint is tested using a servo controlled hydraulic testing machine; to measure its strength ...
10
A Comparison between Two Field Methods of Evaluation of Liquefaction Potential in the Bandar Abbas City
... laboratory tests such as cyclic simple shear, cyclic triaxial, cyclic torsional shear, and field methods such as Standard Penetration Test (SPT), Cone Penetration Test (CPT), and Shear Wave ...
5
Determination of shear parameters of concrete filled head-straight masonry brick walls
... predict shear strength of masonry structure, it can be con- sidered that value of the shear strength calculated by formula (5) is the most suitable and reliable ...estimates shear strength of brick ...
11
Prediction of NUPEC's Multi-Axis Loading Tests of Reinforced Concrete Shear Walls
... The Nuclear Power Engineering Corporation (NUPEC) of Japan is performing multi-axis loading tests of reinforced concrete (RC) shear wall models.. The static tests are [r] ...
8