steel sheets
Estimation of Planar Anisotropy of the r Value in Ferritic Stainless Steel Sheets
... stainless steel sheets and some Fe-3% Si steel sheets have inhomogeneous texture in the thickness ...the sheets in the thickness direction have been suggested for low-carbon ...
7
FORMING ANALYSIS OF CONTINUOSLY ANNEALED, DOUBLE REDUCED STEEL SHEETS
... thin sheets has undergone significant changes over the ...packaging sheets from the origi- nal thickness from ...packaging sheets, higher strength properties, in particular the Yield strength, are ...
5
Effects of Steel Coatings on Electrode Life in Resistance Spot Welding of Galvannealed Steel Sheets
... Figure 2 shows the carbon imprints of electrode tip faces at the start of the stabilization test, and the start and end of the endurance test with electrode tip face diameter as 4.91, 4.88 and 4.90 mm respectively for ...
7
Fracture Behaviour of Cold Rolled Close Annealed Steel Sheets with Defects
... The experimental and theoretical study has done. The specimen used is Cold Rolled Close Annealed Steel Sheets. Straight, edge and inclined cracks and holes were selected as the defects. For cracks, weld was ...
8
Reducing Work Load and Increasing Dimensional Accuracy in Parts for Bending of High Strength Steel Sheets for Automobiles
... high-strength steel. From here on, the application of ultrahigh-strength steel in the 780–1180 MPa range is expected to expand, and to this end, basic data is ...strength steel in V-bending in detail ...
6
Fine Grained Doubly Oriented Silicon Steel Sheets and Mechanism of Cube Texture Development*
... Fe–3%Si sheets with a similar coarse-grained ...silicon steel sheets containing AlN as a grain growth inhibitor are cross-rolled after hot-rolling, decarburized and then annealed at a high ...
10
Resistance Spot Welding of Steel Sheets of the Same and Different Thickness
... connected sheets at collective influence of compressive ...using steel sheets of the same and different thickness for different welding ...The sheets (a total of 720 pieces) of dimensions 100 ...
8
Investigation of the Effect of Skin-Pass on of Mild Steel Sheets
... The steel industry has made many attempts to enhance the quality of their products so that they would lead to easier and faster metal-forming ...Industrial steel sheets with typical values of (r) in ...
8
Investigation of the Formability Enhancement of DP600 Steel Sheets in Electrohydraulic Die Forming
... Huh, Bok & Moon (2011) performed uniaxial tensile tests and high-speed crash tests at high strain-rates, which showed that the strain rate had a noticeable influence on the formability of steel sheets. ...
156
Microstructure and Joint Strength of Friction Stir Spot Welded 6022 Aluminum Alloy Sheets and Plated Steel Sheets
... alloy, hereafter), four kinds of 1.2 mm-thick plated steel sheets and a 1.2 mm-thick non-plated low carbon steel sheet were prepared. These materials were supplied from the Mitsubishi Motors ...
8
Soldering steel sheets using soft solders
... material steel sheet of 1.0 mm thickness and zinc-coated steel sheet of ...Two sheets were always cleaned and jointed ...of steel sheets as well of zinc-coated steel ...
6
Effect of Tool Materials on Frictional Properties of Galvannealed Steel Sheets
... Galvannealed steel sheets (GA) are commonly used as au- tomotive body materials due to their excellent corrosion resis- ...between sheets and dies are im- portant for automotive materials, as these ...
7
The Influence of Technological Factors on the Strength of Adhesive Joints of Steel Sheets
... ensuring the desired strength of the joint [10, 11]. The process of surface treatment involves the re‑ moval of impurities and the appropriate develop‑ ment of the joined surfaces. The choice of sur‑ face treatment ...
9
Improving the Punching Shear Strength of RC Slabs by FRP and Steel Sheets
... Metwally [9] evaluates the punching shear strength of RC flat slabs reinforced with different types of FRP. The experimental punching shear strengths were compared with the available theoretical predictions and a number ...
17
Experimental and Numerical Investigations into the failure mechanisms of TRIP700 steel sheets
... The cross-die deep drawing is able to cover a wide range of stress states. The experimental setup and the final product configuration, are shown in Fig. 4. The side dimensions of initial square blanks were about 270 mm. ...
28
Investigation of the Formability of TRIP780 Steel Sheets
... by the bending effect of the hemispherical Nakazima punch, and the magnitude of the minor strain caused by bending is accurately calculated. The simulated strain path does slightly deviate from the experimental strain ...
125
Microstructural Development during Mechanical Forming of Steel Sheets
... Published literature in this field of study include the research work conducted by Liu et al., [10] who investigated the deformation behavior of mild steel. The investigation entailed the heating of a rectangular ...
6
Mathematical Modelling Study of Hardox400 Steel Parts’ Roughness and Hardness, Cut with CO2 Laser
... This study supports the research in the field of laser cutting of steel sheets HARDOX400 (H400), a less well-known and analysed material. An H400 sheet with a thickness of 10 mm was used; a cutting plan was ...
15
Buckling Behaviour of Cold Formed Steel Sections
... structural steel sheets by bending or forming into different shapes by roll forming the steel through a series of ...of steel thicknesses are available that meet a wide range of structural and ...
5
Analysis of the strain induced martensitic transformation in austenitic steel subjected to dynamic perforation
... Steel sheets are cost-efficient and easily affordable mate- rials, with valuable properties for the industry. In some industrial applications, they are prone to su ff er dynamic indentation or perforation: ...
5