The Received Signal
Indoor positioning and tracking based on the received signal strength
... are received by wireless enabled devices and the information is extracted using Network Interface Cards (NICs) ...the Received Signal Strength Indicator (RSSI), called also as Received ...
165
Enhancement of Noise Performance in Digital Receivers by Over Sampling the Received Signal
... the received signal and calculating the time average of the correlator out- put based on more than one sample in the deci- sion ...desired signal value where the noise aver- age will approach to ...
10
Effect of shadowing and diffraction on the received GNSS signal
... GNSS received signal depend on the propagation medium ...transmitted signal interacts with several numbers of obstacles which leads to the multipath propagation to receiver ...the received ...
43
Real-time localization using received signal strength
... The transmitter shown in Figure 5 is also a G4-SSN mote with a single quarter wave antenna. To prevent the receivers RSSI measurement circuitry from saturating when the received signal’s RSSI value was greater ...
227
On the analysis of received signal strength indicator from ESP8266
... the Received Signal Strength Indicator readings from the ...the Received Signal Strength Indicator readings collected using ESP8266 WiFi serial transceiver module is carried ...of ...
8
Properties of Indoor Received Signal Strength for WLAN Location Fingerprinting
... a signal from the same AP at a particular location except when the user’s orientation blocks that ...the received signal level is, the smaller the degree of standard ...the signal attenuation ...
10
Research Article ResearchonWirelessSensorNetworkSecurityLocationBasedon Received Signal Strength Indicator Sybil Attack
... the received signal strength and signal transmission distance, and the influence of the two constants on the signal transmission distance was ...the signal propagation factor n was a ...
9
An Improved Outliers Detection Algorithm for Received Signal Strength Measurements in Building Environment
... 0 , (1) Where P t , P 0 are the received signal power from the distance from d i and d 0 , respectively, n i is model noise, and is path-loss factor. Assume that we have M grids in an indoor scenario, C ...
5
Novel Received Signal Strength Based Indoor Location System: Development and Testing
... founded on the decay law of the received signal versus the distance. ToA and TDoA methods require the use of ultra wide- band (UWB) devices in order to achieve enough temporal resolution, so that the echoes ...
11
Forecast-Driven Enhancement of Received Signal Strength (RSS)-Based Localization Systems
... Radio signal measurements are typically the received signal strength (RSS), the angle of arrival (AOA), the time of arrival (TOA) and the time difference of arrival ...
18
Combine Received Signal Strength and Angle of Arrival based Localization Technique for WSN
... 3.1 Received Signal Strength Based Localization By definition, the received signal strength is the voltage or power measured at the receiver end using signal strength indicator (RSSI) ...
5
ICESat GLAS Altimetry Measurements: Received Signal Dynamic Range and Saturation Correction
... the received signal from snow and ice surfaces was found to span a wider dynamic range than planned, often exceeding the linear dynamic range of the GLAS 1064-nm detector ...recorded signal and ...
18
Direct Path Interference Suppression and Received Signal Processing for OFDM Passive Radar
... to signal structure were derived for LTE, DVB and DAB ...the signal to be processed as one ...the received signal, and therefore any Doppler ambiguities and non-zero Doppler range ambiguities ...
105
Received signal strength intensity based localization of partial discharge in high voltage systems
... proposed algorithm works purely based on the received signal strength and source coordinates are estimated by converting the received signal strength into distance. The RSS technique is based ...
5
Analysis of RFID Based Positioning Technique Using Received Signal Strength and Directional Antenna
... 2. Previous Measuring Techniques and Positioning Systems 2.1. Measuring Principles and Techniques Considering environmental factors such as reflecting surface, line-of-sight, continuous moving objects, size of the floor ...
10
Enhanced Security Frame Work for Smart IoT Environment using Received Signal Strength
... 2 Department of Electronics and Communication, Engineering IUST, Awantipora J&K Abstract: The aim of this paper is to create a secret key between two different IoT wireless entities while not the necessity for sharing ...
7
Received Signal Strength Based Detection and Localization of Multiple Spoofing Attacks in Wireless Networks
... the received signal strength based spatial correlation, a physical property present in the wireless node that is difficult to falsify and they are not depends on cryptography for detecting spoofing ...
6
Spatial Sampling Requirements for Received Signal Level Measurements in Cellular Networks of Suburban Area
... A process for the determination of a required spatial resolution in the collection of the Received Signal Level (RSL) is discussed. This method considers RSL measurements as a three dimensional surface that ...
11
An efficient algorithm for partial discharge localization in high-voltage systems using received signal strength
... Abstract: The term partial discharge (PD) refers to a partial bridging of insulating material between electrodes that sustain an electric field in high-voltage (HV) systems. Long-term PD activity can lead to catastrophic ...
19
A Kriging Algorithm for Fingerprinting Positioning with received Signal Strengths
... Abstract —Received signal strength (RSS) based location finger- printing is a powerful wireless positioning technique. It estimates the target location by consulting a preliminary database and searching for ...
7