wide-band receiver design
One Kind Used in Wideband Receiver Band stop Filter Design
... surveillance receiver capable of receiving electromagnetic signals and record radio, radar and weapons control systems and other electronic devices emitted identify these technical parameters and tactical ...
5
Design Of High Performance Wide Band Rotman Lens In X-Band
... Geometry and design parameters of a microstripRotman lens is shown in Fig. 2 [11]. In this figure G,F 1 and F 2 are ideal focal and ε r ,ε e , ε i are the permittivity of each regions. W is length of transmition ...
5
Design Of Rf Front-End Mixer With A Gain Of 18 Db Over The Band Of 3.1-10.2 Ghz For An Ultra Wide Band Receiver
... Ultra Wide Band (UWB) Receiver is ...the band of ...same band of ...conversion receiver because of its superior gain and noise figure compared to the passive ...
5
Active Inductor based Low Noise Amplifier for Ultra Wide Band Receiver
... In this paper a three stage Active Inductor (AI) based Low Noise Amplifier (LNA) for Ultra Wide Band (UWB) receiver is presented. A fully differential topology has been adopted in order to improve ...
8
High-Gain CMOS Low Noise Amplifier for Ultra Wide-Band Wireless Receiver
... The design consists of a wideband input impedance matching network, a cascoded amplifier with inductively-degenerated LNA, and an output impedance matching ...
9
Design of Radial Microstrip Band Pass Filter with Wide Stop-Band Characteristics for GPS Application
... compact band pass filter (BPF) is proposed for Global Positioning System (GPS) ...GPS receiver requirement and the minimum insertion loss (IL) in pass-band is ...
8
Wireless Ultra-Wide Band Transmission of (Bio)Signals
... study, design, fabrication and test of microelectronic circuits used to exploit Ultra- Wide-Band (UWB) wireless communication for bio-medical ...a receiver circuit that we have built up using ...
5
Research, Design and Fabrication Microwave Modules of Receiver for NanoDragon satellite at S band
... Mixer is designed depend on microwave signal input and bandwidth requirement. In this case, Mixer used LT5527. Features of LT2257: have 16 pins; size 4 mm x 4 mm; wide RF frequency rage is 400 MHz to 3.7 GHz; ...
10
Design of Integrated Triple Band Notched for Ultra Wide Band Microstrip Antenna
... GHz band as the ...a band-stop filter at the receiver antenna we have etched a C-shaped slot on the radiating patch in order to facilitate band-rejection facility around ...this design ...
11
Design of a Wide-Band Blade Monopole Antenna in 135-175 MHz Band
... As the aluminium tube has been placed horizontally over the blade, there exist two prominent polarizations. One is the vertical polarization due to the blade part of the monopole antenna (as the feed is aligned ...
8
A Reconfigurable Low Noise Amplifier for a Multi-standard Receiver
... to design multi-standard multi-band LNA with a good performance, a good topology for such device is needed to support the required ...these wide band LNAs were not designed as a single LNA but ...
250
Design of RF Front End Mixer Circuit for an Ultra Wide Band Receiver
... the SNR of the receiver signal. Because of the conversion loss, the use of a passive mixer in a DCR will degrade the noise figure of the receiver chain. Furthermore, higher gain is required for the LNA to ...
5
Study and design of wide band low noise amplifier operating at C band
... satellite receiver systems, a low noise amplifier, which is placed right after the antenna, is ...the receiver has the dominant effect of the noise of the first amplifier stage ...to design the LNA ...
9
Design of a Passive Vibration Absorber to Attenuate Wide Band Vibration
... Wide band vibration was reduced by using a passive vibration ...for wide band vibration design and the effect of the parameters toward the bandwidth of vibration control had been ...
5
MFJ-8100 World Band Receiver
... the receiver OFF when not in use! This "advice'' may seem ridiculously obvious, but remember that battery replacement requires removing and replacing the 8 cabinet screws and that leaving the receiver ...
27
RF switches in wide , broad , and multi band RF front end of wireless communications: An overview
... This design used PIN diodes to operate with multi-band frequencies in order to be applicable for three wireless applications in ...GHz band for global positioning system (GPS), vehicle information ...
5
design and simulation of dual band microstrip array antenna for IRNSS Receiver
... The IRNSS is Indian Regional Navigational Satellite system which is developed by the ISRO(Indian Space Research Organization) and it would be under complete control of the Indian Government[4]. The reuirement of such ...
6
Typical Ka band Satellite Beacon Receiver Design for Propagation Experimentation
... The LNB is fed by IF output. The appropriate gain, ultra-low noise factor and good internal consistency of the local frequency are its features. In Fig. 3, the received signal at the input antenna after entering into the ...
6
Design of Circular Monopole Antenna for Ultra Wide Band Application
... The fast growing technology and development in wide band wireless technology system has increased the use of Ultra Wideband (UWB) antennas. After releasing a 10-dB bandwidth of 7.5 GHz (3.1-10.6 GHz) by ...
5
Design and Analysis of Re-Configurable Dual Band-Notched Micro-Strip Wide-Band Antenna
... Ultra wideband (UWB) technology has gained a lot of popularity among researchers and the wireless industry after the FCC permitted its marketing within the frequency band of 3.1 GHz to 10.6 GHz [1]. The ...
11