FEATURE DATA (0/1)
BASIC SERVICE: 301-398
: Default
BASIC SERVICE SETTING DATA
301 When system is reseted 0
1
Multiline Terminal MIC lamp ON Multiline Terminal MIC lamp OFF
311 Display last calling station number 0
1
6 seconds Until next call Display calling station number when a calling station abandons
a call before the call is answered
0 1
Not available Available 313 An Incoming call via UCD station in Exclusive Hold/Remote
Hold
0 1
Not income To income 319 On a Tie Line outgoing call with answer signal, transferring/
holding the call before distant called station answers.
NOTE: Effective only when CM35 Y=000 is 03 or 04 and CM35 Y=004 is 02.
0 1
Not available Available
322 Answering method of Camp-On (Call Waiting Method) 0
1
Same as Camp-On transfer-method (Switch Hook Flash + Call Hold access code/Answer key)
Alternating between two calls by Switch Hook Flash/Answer key 324 Direct-In Termination-Outside
(In the case of no release signal on incoming trunk and both answer and release signals on outgoing trunk)
[8300R2]
0
1
After the outgoing trunk receives the response, the tandem connection is allowed
The tandem connection is restricted when the incoming trunk is no resto-ration signal
331 Sender Prepause for outgoing call via attendant 0 1
To provide Not provided 333 Mail box number sent to VMS when VMS is recalled after
transferring the call to an unanswered station
0 1
To send Not sent 334 Call to a station with a Return Message Schedule Display, and
receives ringing
0 1
Available (Ringing)
Not available (ROT connection) 335 Station number and name display when incoming call begins
ringing in
0
1
Display when incoming call termi-nates to the Prime Line
Display when incoming call termi-nates to the Prime Line or My Line
Continued on next page
RESET
JULY/17/2009
3-53 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
352 When a call is transferred by Remote Access to System (DISA) to predetermined station and time-out occurs, the call is contin-ued or dropped
See CM30 Y=30 CM41 Y=0>39 0 1
Disconnect call Continue call
353 Buzzer sound when terminating incoming call to attendant that is in Attendant Console Lockout
0 1
Not provided To provide 357 Diversion display on Multiline Terminal/DESKCON when
originating/terminating a call
0 1
Available Not available 359 When a call is transferred by Automated Attendant to
predeter-mined station and time out occurs, the call is continued or dropped
See CM30 Y=30, 31, 32, 33 CM41 Y=0>39 0 1
Disconnect call Continue call
361 Dial “**” is automatically added to the digits sent to Radio Paging System
0 1
Allowed Restricted 362 Confirmation tone after dialing access code for Account Code/
Authorization Code/Forced Account Code
0 1
No tone
Service Set Tone 363 For Automated Attendant call, caller dials while receiving
message or music
0
1
Not allowed
(Allowed after receiving the message or music)
Allowed 365 Send Dial Tone when holding trunk by Hold key
See CM90 Y=00: F0058 0 1
To send Not sent 367 Camp-On (Call Waiting) Tone sent to busy station by Call
Wait-ing-Station/-Terminating (Camp-On Call Waiting method) NOTE: In Italy, Belgium, Denmark, Switzerland and Spain, you
have to set setting data to 0.
0 1
Every 4 seconds Only once
368 Centralized Billing-CCIS for Center Office 0 1
To provide (for Center Office) Not provided (for Local Office) 369 Automatic return of originating station to the held C.O. line
call, after the inquiry call is disconnected.
0 1
Automatic return to C.O. line call Return to C.O. line call via hooking, when receiving ROT
370 Call Forwarding-Outside-CCIS on incoming call from CCIS 0 1
Restricted Allowed
Continued on next page
JANUARY/31/2012
3-54 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
371 Call Forwarding Override-CCIS 0
1
Not available (BT connection) Available
372 Alternative Routing when outgoing trunks of tandem office are all busy/Alternate Routing for multiple SIP
0 1
Available Not available 376 When forwarded call is terminated to VMS via CCIS, whether
Message Waiting from VMS is provided for the called station 0 1
To provide Not provided 377 Send calling party information to SMDR on CCIS tandem calls 0
1
Station number and Office number Trunk Route number and Trunk num-ber
378 Centralized Billing-CCIS for Local Office 0 1
To provide (for Local Office) Not provided (for Center Office) 379 Maximum number of dialed digits sent to the CCIS 0
1
24 digits 15 digits When a call is terminated via CCIS/SIP, whether Caller ID
Dis-play/Name Display (Attendant Called/Calling Name Display) is provided for the called station.
0 1
To provide Not provided
380 Interval of ringer until detecting a ringing frequency from the main PBX or Centrex.
Ringing is sent from Multiline Terminal until detection of the ringing frequency.
0 1
As per CM08>381 As per CM35 Y=033
381 Interval of ringer until detecting a ringing frequency from the main PBX or Centrex.
Ringing is sent from Multiline Terminal until detection of the ringing frequency.
NOTE: Effective only when the 2nd data of CM08>380: 0.
0 1
No Ringer
Ringing Tone (0.5 seconds) is sent once
382 Lamp indication of Multiline Terminal until detecting the kind of incoming call from main PBX or Centrex.
The lamp is lit until detection of the ringing frequency.
0 1
Red steady light
120 IPM flash (As per CM35 Y=032)
386 Destination setting of Call Forwarding-All Calls/Busy Line/No Answer-Outside or Split Call Forwarding-All Calls/Busy Line/
No Answer-Outside by entering only a trunk access code
0 1
Restricted Allowed
388 Holding/held party control for Music on Hold tenant basis 0 1
Held party control (tenant) Holding party control (tenant)
Continued on next page
JULY/17/2009
3-55 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
390 Multiline Terminal tone ringer selection
NOTE 1: Set “0” (Available) by CM08>262 to allow the ring test tone to be heard when using the “Feature + 3”
operation.
NOTE 2: When the ring tone 600 + 700 (Hz) is specified in CM15 Y=083, 084 and/or CM35 Y=034, the ring tone selection key of Multiline Terminal is ineffec-tive.
0
1
By pressing Feature key and dialing 3 NOTE 1 As per CM15 Y=083, 084, 093,
CM35 Y=034, 164 NOTE 2
391 Lamp indication on Multiline Terminal 0
1
Special Standard 392 Multiline Terminal ringing signal patterns for external call
[Other than North America]
0 1
2 seconds ON-4 seconds OFF 0.4 seconds ON-0.2 seconds OFF -0.4 seconds ON-2 seconds OFF 394 Message Waiting lamp indication of Single Line Lamp 0
1
Flashing (1 second ON-1 second OFF)
Steady lighting 396 Multiline Terminal ringing cadence selection for Internal call
[Other than North America/Australia]
0 1
2 seconds ON-4 seconds OFF 1 second ON-2 seconds OFF
Continued on next page
RESET
JANUARY/31/2012
3-56 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default