FEATURE DATA (0/1)
BASIC SERVICE: 400-489
: Default
BASIC SERVICE SETTING DATA
400 Send Calling Party Subaddress to ISDN network 0 1
To send Not sent 401 Terminating system for Called Party Subaddress 0
1
Station call
Terminating system assigned by CM30 Y=02/03/40/41
402 Advice of Charge (AOC) display on Multiline Terminal when the charge has been summed over $9999.99/€ (Euro) 655.35 (After 6 seconds, the display goes off.)
[Australia/France/Germany/Netherlands/Italy/Greece/
Luxembourg/Portugal/Spain/Sweden]
0 1
Flashing display Fixed display
403 Timing start when making ISDN call from attendant [8300R2]
0 1
Not available Available 404 Advice of Charge
[Australia/France/Germany/Netherlands/Italy/Greece/
Luxembourg/Portugal/Spain/Sweden]
0 1
Not available Available
405 Consecutive Speed Dialing when making ISDN call 0 1
Available Not available 407 Busy tone is sent to calling party of ISDN when called party is
busy in tandem connection (ISDN to COT)
0 1
Available (BT) Not available (RBT) 420 Frequency of metering pulse for COT
[Australia Only]
0 1
16 kHz 50 Hz/12 kHz
422 Multiline Terminal speaker volume control (6dB gain) in on-hook speaker mode
[Australia Only]
0 1
Available Not available
424 Method of charging a transferred call 0
1
Charging to transferring station or transfer destination station
Split charging to both transferring sta-tion and transfer destinasta-tion stasta-tion
Continued on next page
RESET
JULY/17/2009
3-59 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
425 Charging to the transferring station or transfer destination sta-tion
0 1
Charging to transferring station Charging to transfer destination sta-tion
Shown below are stations to which call is to be charged in the case of various transfer patterns.
426 SMDR for incoming calls if the account code is not entered NOTE: When CM08>426 is 1, SMDR for incoming call is not
provided even if CM13 Y=05 and CM35 Y=049 are 0 (To provide).
0 1
To provide Not provided
427 Send additional DTMF signals when called station answers, if assigning station number and additional DTMF signals to One-Touch key on Multiline Terminal.
0 1
To send Not sent
428 VMS transfer from attendant, if Camp-On is set and not answered
0 1
To provide Not provided 429 Automatic setting of OAI SMFR for Multiline Terminal Sub
line
[Cintech Jazz ACD only]
0 1
Available Not available
430 Send Calling Party Subaddress to ISDN network when making call from ISDN Telephone
0 1
To send (As per CM08>431) Not sent
431 ISDN Calling Party Subaddress when making call from ISDN Telephone
0
1
ISDN line station No. assigned by CM10 Y=00
ISDN Telephone No.
Continued on next page STA: station DESKCON: Desk Console Transfer Pattern
CM08>424=1 CM08>424=0 CM08>425=1
CM08>424=0 CM08>425=0
From To
STA A STA B Split charging to STA A and
STA B STA B STA A
STA DESKCON STA STA STA
DESKCON STA STA STA STA
DESKCON A DESKCON B Split charging to DESKCON
A and DESKCON B DESKCON B DESKCON A
JULY/17/2009
3-60 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
432 Forced release when called ISDN Telephone does not answer for 3 minutes
0 1
Not available Available 434 ISDN CPN (Calling Party Number) when making a call from
ISDN Telephone
0 1
CPN entered in ISDN Telephone CPN assigned by CM12 Y=12/13
441 Recall display on Attendant Console 0
1
Available Not available
442 ACD/UCD Busy Out from Sub line 0
1
Available Not available
443 Type of Voice Mail System (VMS) 0
1
As per CM12 Y=25 VMS with DTMF signaling 444 Message Waiting lamp control from VMS with MCI to all
stations
NOTE: MW lamp control is only available to stations in the op-posite PBX connected with CCIS via MCI. Station di-aling MW access codes are not allowed over CCIS.
0 1
Available Not available
445 Pressing Paging key on DESKCON when the attendant is in idle
0 1
Available Not available 448 When Multiline Terminal station dials “*#” during setting of
One-Touch keys
0 1
“*#” is set as dialed digit
“*#” is set as a delimiter mark between dialed number and DTMF signal
449 DID call to station with Call Forwarding-No Answer-CCIS set to a busy destination station.
Destination has no call forwarding set.
0
1
Ring continuously at forwarded DID station
Drop to busy signal after time set by CM41 Y=0>01
450 Fault Information Storing 0
1
Not stored To store 460 Send OAI SMFN STS (status) for Call Transfer from station 0
1
SMFN STS=7 SMFN STS=0
461 Send OAI SMFN when answering held call 0
1
To send Not sent
462 Send ANI/Caller ID/CPN to OAI terminal 0
1
To send Not sent
Continued on next page
JUNE/15/2011
3-61 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
463 Send ANI/Caller ID/CPN to SMDR terminal 0
1
To send Not sent 464 OAI TSAPI
SCF facility
0
1
Same as 2400 IPX system (recom-mended setting)
SMFN Off-Hook indication sent
465 SCF error code type 0
1
SCF error Detail SCF error Kind 467 Method of readout the traffic information 0
1
To readout from the newest data To readout from the oldest data NOTE: Set the second data to 0 when measuring traffic data continuously per hour/day.
470 Send Backward GB signal when terminating to Attendant Con-sole on DID MFC call
[8300R3.5]
0 1
Subscriber’s Line control Subscriber’s Line Free (Charge)
471 Send Backward GB signal when terminating by tandem con-nection or converting received digits on DID MFC call [8300R3.5]
0 1
Subscriber’s Line control Subscriber’s Line Free (Charge)
472 Request ANI signal/Caller ID from network when incoming call terminates
[8300R3.5]
0 1
Available Not available
473 Assign the connecting method when receiving Backward signal meaning Line Busy/Unallocated number/Congestion
[8300R3.5]
0
1
Not released trunk (Tone/Announce-ment from C.O.)
Release trunk (BT/ROT from PBX) 474 Send ANI signal to PSTN on Enhanced 911
[North America Only]
0 1
To send Not sent 475 Sender Tone sending on Enhanced 911
[North America Only]
0 1
Not sent (No tone) To send
477 Select the Backward signal for ANI signal on DOD MFC call [8300R5]
0
1
Backward GC [Mexico Only]
Backward GA NOTE: Both CM08>477 and 487 should be set the same data.
Continued on next page
JANUARY/31/2011
3-62 NWA-033623-001 Rev.8.1 91ch3001.fm
COMMAND CODE TITLE:
BASIC SERVICES 08
: Default
BASIC SERVICE SETTING DATA
487 Select the Backward signal for ANI signal on DID MFC call [8300R5]
0
1
Backward GC [Mexico Only]
Backward GA NOTE: Both CM08>477 and 487 should be set the same data.
489 Type of Single Data Message Frame Format 0 1
Without Time Parameter With Time Parameter
Continued on next page
JANUARY/31/2011
3-63 NWA-033623-001 Rev.8.1 91ch3001.fm