and Finite Element Modeling
Finite Element Modeling of CARBON nanoTUBES
... experimentally, modeling and simulations could provide crucial insight and design ...uses finite element modeling to predict the mechanical properties of CNTs instead of using expensive ...
5
Finite Element Modeling of Multi-Walled Carbon Nanotubes
... -- Finite element modeling is used to simulate carbon nanotubes, ...three-dimensional finite element (FE) model for Armchair, Chiral and Zigzag si ngle-walled carbon nanotube (S WCNT), ...
9
Finite Element Modeling of Shop Built Spherical Pressure Vessels
... using finite element ap- proach as the analytical tool. 3-D finite element modeling using 3-node shallow triangular element with five degrees of freedom at each node is ...from ...
6
Finite Element Modeling Of Partially Composite Castellated Beams
... numerical finite element modeling were established by Salah and Gizejowski (2008a, 2008b) where a full composite action was ...3D Finite Element Model using ABAQUS software is developed ...
17
Finite Element Modeling for Linear Analysis of Disc Brake
... however finite element modeling using ANSYS Software is demonstrated to provide accurate numerical over a wide range of parameters involved the graphical post processing capabilities exploited to ...
7
Finite Element Modeling of Rotor using ANSYS
... In this paper dynamics analysis of rotor model is done using finite element analysis. The finite element analysis of the rotor is done in Ansys APDL. This analysis of natural frequency under ...
10
Adaptive Finite Element Modeling of Fatigue Crack Propagation
... element method [2, 3], meshfree methods [4,5,6], finite element method (FEM) [7], and finite difference method (FDM) are available. FEM has been in the forefront of numerical methods used for ...
5
Finite element modeling of soil sinkage by multiple loadings
... An alternative approach is to make use of finite element method (FEM). The FEM is now confidently recognized as the most powerful general technique for the numerical solution of a variety of problems ...
8
Extended Finite Element Modeling: Basic Review and Programming
... method finite element is widespread in applications of industrial design, and much of various software pack- ages based on techniques of FEM were ...a finite element mesh proves to be ...
6
Finite Element Modeling and Analysis of Prosthetic Knee Joint
... Computational modeling of the knee provides a way for better understanding the interplay between the hard and soft tissue constituents of the knee during normal and pathologic ...
6
Finite Element Modeling of the Proximal Humerus to Compare Stemless, Short and Standard Stem Humeral Components of Varying Material Stiffness for Shoulder Arthroplasty
... While the application of anisotropic trabecular material properties was one of the strengths of this study, certain assumptions needed to be made to permit the application of a modulus-density relationship. In ...
138
Finite element modeling of occlusal variation in durophagous tooth systems
... of modeling, I generated heat maps demonstrating the distribution of strain in each model, allowing prediction of the most likely location of failure in each tooth model ...
7
Prediction of Burst Pressure of a Radial Truck Tire Using Finite Element Analysis
... of finite element analysis in tire optimal design has become widely ...axisymmetric finite element model has been developed using a commercial finite element code with rebar ...
10
Analytical and Experimental Investigation of I Beam-to-CFT Column Connections under Monotonic Loading (RESEARCH NOTE)
... and finite element models under the monotonic ...the finite element modeling, at first, an experimental model is made and ...the finite element modeling, different ...
14
Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties
... Finite Element Modeling The finite element code, PZFlex [12], has been used to simulate four piezoelectric composite configurations combining PZT5H and PMN-PT as the active piezoelectric[r] ...
8
IJARSE, Vol. No.4, Issue No.02, February 2015 ISSN-2319-8354(E)
... The finite element modeling and dynamic analysis of massive and elevated foundation of steam turbine generator is ...The element type, element size and damping ratio are very important ...
7
Study of Lateral Vibration of Drilling String with Mass Imbalance Using Finite Element
... studies, finite element analysis of the proposed BHAs consisting of two motor configurations was used to determine the critical speeds, as well as the speeds that cause the stabilizers to bounce from side ...
6
Mathematical Modeling of Hydrogels Swelling Based on the Finite Element Method
... In this study, the swelling dynamics of initially dry hydrogel samples is numerically modeled using the finite element method. Due to the numerical approach chosen, the sample shapes to be considered can ...
10
Hybrid finite difference–finite element method to incorporate topography and bathymetry for two dimensional magnetotelluric modeling
... Based on these results, the hybrid method may rep- resent a new, better option for the forward calculation routine for 2-D magnetotelluric inversion to interpret real field magnetotelluric data in the future. Note that ...
14
Aortic endovascular repair modeling using the finite element method
... We note a very significant stiffness gradient between the tip and the stiff zone of the guide, which is added gradually in the transition area. The tips of different guides used in the clinical setting have a stiffness ...
11