Bearing and Pump
Investigation of Non-linear Reactions in Rotors’ Bearing Supports of Turbo-pump Units for Liquid Rocket Engines | Journal of Engineering Sciences
... of bearing supports ...s bearing supports is proposed for turbo-pump units for liquid rocket ...the bearing support on the scheme “ remote force ” in a wide range of rotor speeds, the ...
9
DEVELOPMENT AND CHARACTERIZATION OF OSMOTIC PUMP TABLETS BEARING ANTIDIABETIC DRUG
... From the results obtained, it can be inferred that the release of Metformin HCl and Glipizide from elementary osmotic pump can be controlled efficiently by the addition of hydrophilic polymer to enhance the ...
11
DEVELOPMENT AND EVALUATION OF ELEMENTARY OSMOTIC PUMP TABLETS BEARING ANTIDIABETIC DRUG
... osmotic pump tablets were selected for stability study on the basis of In vitro dissolution profile and their physical ...osmotic pump tablets were investigated at 40 0 C/75% RH in aluminium foil packaging ...
13
Performance Evaluation of Centrifugal Type Boiler Feed Pump by Varying Blade Number
... centrifugal pump, the parts to be designed are: shaft, impeller, vane, casing, and selection of ...speed, pump of double volute, double suction and single stage type is ...
6
“Analysis For Operating Cost Of Split Case Pump For Its Life Cycle”
... Precision casting in austenitic stainless steel is standard scope of supply. Axially hydraulic balance of double suction design improves efficiency and enhances bearing life. Rotating assemblies are dynamically ...
5
On the Design, Modeling, and Control of a Hybrid Pump System for Dynamic Pressurization of Explanted Mammalian Hearts
... VCAD pump based on the BEI KIMCO LA13-12-000-LTR voice coil actuator along with a simple yet effective bearing system has been designed and ...gear pump, the hybrid VCAD/gear pump system ...
80
The Effect of Damping and Stiffness of Bearing on the Natural Frequencies of Rotor-bearing System
... Rotor dynamics is the branch of engineering that studies the lateral and torsional vibrations of rotating shafts, with the objective of predicting the rotor vibrations and containing the vibration level under an ...
8
FAILURE ANALYSIS OF CENTRIFUGAL PUMPS BASED ON SURVEY
... agricultural and industrial users were analyzed. Most vulnerable components in a centrifugal pump are packing and bearing, as revealed by analysis of survey data. Impeller ranks third in terms of useful ...
6
Rotor Dynamics Analysis of a Multistage Centrifugal Pump
... the pump. The coupling between pump gear and motor is flexible so the gear and motor are not considered in the calculation and ...mass, bearing properties and material properties are extracted from ...
9
VIBRATION ANALYSIS OF BEARINGS USING FFT ANALYZER
... feed pump bearing casing there are fluctuations in the graph which occurred at regular intervals then shaft is imbalance so there is no need of replacing the bearings only there is need of repairing the ...
11
Investigation of Spherical Bearings for Use in the UltraForm Finishing Polishing Process
... The hydrostatic analysis from Section 3.4 can now be applied to estimate the actual bearing eccentricity. The belt was tensioned on the machine at several discrete pressure intervals. The tensioner provides a ...
81
DESIGN AND FABRICATION OF SWEEP PUMP Dinesh Babu Deenadayalan 1 Mohanraj Rajasekaran 2, Venkatesan Selvaraj3 , Balakumar Jeyakumar 4
... the bearing in the bearing house. Then the bearing housing should be fitted into the cylinder and lock nut is provided to lock the cylinder and the bearing housing and the o ring provided at ...
7
Analysis of journal bearing performance with textures on bearing surface using CFD as a tool
... introduced in place of spherical shaped dimple at the most efficient place on the bearing surface as found out by Cupillard et al in their work mentioned in reference (Cupillard et al., 2008). Below is the ...
8
Design, Fabrication and Validation of a Laboratory Flow Loop for Hydrate Studies
... When temperature was plotted against time in the experimental run conducted with gas alone (Figure 13), temperature initially declined with time from 33°C to 20°Cat 24 minutes. As the gas was being cooled, water ...
14
Optimization Gear Oil Pump in Order to Energy Saving and Environmental Impact in a Diesel Engine
... Oil pump in diesel engine has significant effect on energy consumption and environment ...oil pump used in a diesel engine and its fluid flow analysis by a solver has been ...oil pump is external ...
12
Fluid pumping system based on electrochemically induced surface tension changes
... A pump for exerting a pumping force on a fluid in an attached conduit, the pump being actuated by a voltage from a power supply, the pump comprising a liquid metal pool, a containment vessel for ...
17
Theoretical Study of the Thermal Distribution in Yb-Doped Double-Clad Fiber Laser by Considering Different Heat Sources
... improve pump absorption and increase the fraction of cladding modes overlap with the active core area, the rotational symmetry of the first clad must be broken with different shapes of first clad cross-section, in ...
18
Parametric Study of Centrifugal Pump and its Performance Analysis using CFD
... various pump types, the use of which reduces significantly the new pump development time and ...of pump impellers and helps us rapidly to establish the efficiency of the pump over various ...
7
“DESIGN, ANALYSIS & FABRICATION OF HYDRAULIC RAM PUMP FOR REMOTE AREAS ”
... ram pump (also called hydram) is a pump that uses energy from a Falling quantity of water to pump some of it to an elevation much higher than the original level at the ...ram pump is simple. ...
7
Investigating the Validity of Acoustic Spectrum as a Prediction Tool for Pump Cavitation
... Hydraulic sources of noise include both the transient and instationarity of flow causes; Transients; during the startup and shutdown of the pump, opening or closing of servicing valves may cause severe pressure ...
9