• No results found

Finite Element Modeling

Finite element modeling (FEM) simulation of interactions between wood and microwaves

Finite element modeling (FEM) simulation of interactions between wood and microwaves

... use finite element modeling (FEM) as a tool to analyze microwave scattering in wood and to verify the model by measurements with a microwave ...

5

Finite Element Modeling for Linear Analysis of Disc Brake

Finite Element Modeling for Linear Analysis of Disc Brake

... however finite element modeling using ANSYS Software is demonstrated to provide accurate numerical over a wide range of parameters involved the graphical post processing capabilities exploited to ...

7

Finite Element Modeling Of Partially Composite Castellated Beams

Finite Element Modeling Of Partially Composite Castellated Beams

... numerical finite element modeling were established by Salah and Gizejowski (2008a, 2008b) where a full composite action was ...3D Finite Element Model using ABAQUS software is developed ...

17

Finite Element Modeling Of Piezoelectric Patches for Vibration Analysis of Structures

Finite Element Modeling Of Piezoelectric Patches for Vibration Analysis of Structures

... The project work presents the fundamental conceptual knowledge about piezoelectricity, piezoelectric effect and its different domains, piezoelectric materials, piezoelectric patches and finally works strategy. The ...

7

Finite Element Modeling of Multi-Walled Carbon Nanotubes

Finite Element Modeling of Multi-Walled Carbon Nanotubes

... -- Finite element modeling is used to simulate carbon nanotubes, ...three-dimensional finite element (FE) model for Armchair, Chiral and Zigzag si ngle-walled carbon nanotube (S WCNT), ...

9

Finite Element Modeling of Stamp Forming Process on Fiber Metal Laminates

Finite Element Modeling of Stamp Forming Process on Fiber Metal Laminates

... Experimental analysis has limitations. For example, the strain distribution in areas of no visibility cannot be measured. To overcome such drawbacks, finite element modeling was implemented ...

6

Finite Element Modeling of Shop Built Spherical Pressure Vessels

Finite Element Modeling of Shop Built Spherical Pressure Vessels

... using finite element ap- proach as the analytical tool. 3-D finite element modeling using 3-node shallow triangular element with five degrees of freedom at each node is ...from ...

6

Finite Element Modeling of CARBON nanoTUBES

Finite Element Modeling of CARBON nanoTUBES

... experimentally, modeling and simulations could provide crucial insight and design ...uses finite element modeling to predict the mechanical properties of CNTs instead of using expensive ...

5

Finite element modeling of occlusal variation in durophagous tooth systems

Finite element modeling of occlusal variation in durophagous tooth systems

... of modeling, I generated heat maps demonstrating the distribution of strain in each model, allowing prediction of the most likely location of failure in each tooth model ...

7

Finite Element Modeling and Analysis of Sandwich Dry Floor Slab

Finite Element Modeling and Analysis of Sandwich Dry Floor Slab

... preliminary finite element models similar to the test specimen was developed and analysed using LUSAS Version ...as element type, material properties, interface connection and boundary ...

6

Finite Element Modeling for Effect of Fire on Steel Structure: A Review

Finite Element Modeling for Effect of Fire on Steel Structure: A Review

... of finite element models to study the inelastic behavior of a steel I-beam in terms of its rotational capacity at elevated ...the finite element method to study the moment–rotation ...

7

Finite Element Modeling, Analysis And Simulation Of Wide Rim Alloy Wheels

Finite Element Modeling, Analysis And Simulation Of Wide Rim Alloy Wheels

... The Finite Element Methods (FEM) will be used to predict maximum displacement and stress of the wheel under specific ...of modeling, analysis and simulation of the ...

24

High frequency finite element modeling and condition assessment of power transformers

High frequency finite element modeling and condition assessment of power transformers

... The hybrid winding model is developed for a continuous disc-type trans- former winding, since this winding type represents the essential part of HV and MV transformer windings. The basic principle of this model is based ...

174

Finite element modeling of the viscoelastic responses of the eye during microvolumetric changes

Finite element modeling of the viscoelastic responses of the eye during microvolumetric changes

... The cornea and sclera were divided by a radial line going through the center of the sclera ellipse. A small transition zone at the cornea-sclera junction was imple- mented with a finer mesh to avoid convergence ...

9

A finite element modeling of the human lumbar unit including the spinal cord

A finite element modeling of the human lumbar unit including the spinal cord

... The numerical modelling based on a finite element methods (FEM) simplifies the structure whether it is ana- tomical or not by reflecting its mechanical properties. This method requires specification of the ...

7

Three-dimensional finite element modeling of ductile crack initiation and propagation

Three-dimensional finite element modeling of ductile crack initiation and propagation

... In order to modify the surface, the computed crack extension direction plane for the crack-front corner is intersected with the triangular outer surface elements. Starting from the old crack-front corner, surface ...

25

Finite Element Modeling and Analysis of Prosthetic Knee Joint

Finite Element Modeling and Analysis of Prosthetic Knee Joint

... solid modeling can be found. The benefits of solid modeling to medicine have not yet been fully explored because of the rapid development of solid modeling ...solid modeling could be done at ...

6

Extended Finite Element Modeling: Basic Review and Programming

Extended Finite Element Modeling: Basic Review and Programming

... extended finite element method was given by its coupling with level set methods (LSM): The LSM is employed to represent both the crack position and that of the crack ...

6

Adaptive Finite Element Modeling of Fatigue Crack Propagation

Adaptive Finite Element Modeling of Fatigue Crack Propagation

... Abstract: An adaptive finite element interactive program has been developed for fatigue crack propagation simulation under constant amplitude loading condition. The purpose of this model is on the ...

5

Finite element modeling of soil sinkage by multiple loadings

Finite element modeling of soil sinkage by multiple loadings

... The finite element method (FEM) was used to predict soil sinkage by multiple loadings (ten loadings) of a rectangular plate and a two-dimensional FEM program entitled PRESSINK was modified and employed to ...

8

Show all 10000 documents...

Related subjects