• No results found

Heat Treatment Temperature

Effect of Heat Treatment Temperature on Mechanical Properties of the AISI 304 Stainless Steel

Effect of Heat Treatment Temperature on Mechanical Properties of the AISI 304 Stainless Steel

... solution treatment at temperature up to 1100°C followed by quenching in ...austenitizing temperature to 1100°C promotes the dissolution of carbide and Cr enrichment in the matrix [13] ...solution ...

5

Effect of heat treatment temperature and time on sound absorption coefficient of Larix kaempferi wood

Effect of heat treatment temperature and time on sound absorption coefficient of Larix kaempferi wood

... When heat-treated wood is used as an interior material, its sound absorption properties should be ...of heat-treated ...of heat-treated wood in accordance with treatment temperature and ...

5

Application of High Frequency Induction Heating Apparatus to Heat Treatment of 6061 Aluminum Alloy

Application of High Frequency Induction Heating Apparatus to Heat Treatment of 6061 Aluminum Alloy

... the temperature at the center of the sample. To investigate the temperature distribution in the sample immediately after the heating process, five thermo- couples (type K) were positioned in the length, ...

9

Innovative Solution of Utilization of the Clay Slates Accumulated in the Gorge of the River Duruji

Innovative Solution of Utilization of the Clay Slates Accumulated in the Gorge of the River Duruji

... the temperature range of 1025-1073К, a change in the color was observed: black deluvium became ...the heat treatment temperature caused the “penetration” of this compound into the bulk ...the ...

6

Discussion on Heat Treatment Process of Welding Weld in Power Plant

Discussion on Heat Treatment Process of Welding Weld in Power Plant

... the heat treatment tube row (as shown in Figure 1 pipe row welding), because the heating sheet is relatively long, if the heating plate is not suitable for fixing, in the heat treatment ...

5

Development of Low Cost Corrosion Resistant Fe-Cr-Mn-Mo White Cast Irons

Development of Low Cost Corrosion Resistant Fe-Cr-Mn-Mo White Cast Irons

... hours heat treatment, the microstructural features were similar to that observed at 800˚C except that much coarsening of both needle like phase and of DSP ...850˚C heat treatment ...

9

A Brief Review on Carbon-Carbon Composites Their Properties and Their Future Aspects

A Brief Review on Carbon-Carbon Composites Their Properties and Their Future Aspects

... Carbon-carbon composites with high thermal conductivity are important for first wall components for nuclear fusion reactors, hypersonic aircraft, missiles and spacecraft, thermal radiator panels and electronic ...

5

Electrooxidation of Methanol on AuNi/C Catalyst in Alkaline Medium

Electrooxidation of Methanol on AuNi/C Catalyst in Alkaline Medium

... the heat treat temperature is higher than 400 °C, moreover, the mean diameters of the AuNi nanoparticles in the AuNi/C catalyst increase dramatically, resulting to its ECSA decrease ...the heat ...

10

The Effect of Austenitization Treatment Temperature on H-13 Tool Steel’s Mechanical Properties

The Effect of Austenitization Treatment Temperature on H-13 Tool Steel’s Mechanical Properties

... of heat treatment temperature on the strength, hardness, and impact toughness of H-13 steel, and to develop a reasonable heat treatment process guide to be used in industrial production ...

6

Mechanical and Corrosion Behavior of Al-Zn-Cr Family Alloys

Mechanical and Corrosion Behavior of Al-Zn-Cr Family Alloys

... room temperature as shown in Figures ...solution heat treatment temperature of 500°C for 60 minutes followed by quenching in water at room temperature as shown in Figures ...heating ...

13

Growth kinetics of MPS capped CdS quantum dots in self assembled thin films

Growth kinetics of MPS capped CdS quantum dots in self assembled thin films

... In the present study, colloidal MPS-capped CdS quantum dots were self-assembled directly on a glass substrate using spin-coating method without introducing any matrix. The coated substrates were heat-treated to ...

7

Microstructure and Magnetic Properties of Sr2Co1.7Mg0.3Fe11.2 Hexaferrite Synthesized by Auto-Combustion Sol-Gel Method

Microstructure and Magnetic Properties of Sr2Co1.7Mg0.3Fe11.2 Hexaferrite Synthesized by Auto-Combustion Sol-Gel Method

... increasing heat treatment temperature above 950 ˚C, while the coercivity decreased from1108 to 637 Oe; moreover, low value of coercivity makes these ferrites potential candidates for security, ...

6

NUMERICAL COMPUTATION OF FLUID FLOW AND HEAT TRANSFER  IN A MEMS-BASED MICRO CHANNEL HEAT SINK

NUMERICAL COMPUTATION OF FLUID FLOW AND HEAT TRANSFER IN A MEMS-BASED MICRO CHANNEL HEAT SINK

... Effective heat removal rate and cooling performance of MEMS-based devices having different types of fin configuration have been investigated numerically in this ...velocity, heat generation, fin material, ...

8

Numerical investigations of heat transfer in phase change materials using non equilibrium model

Numerical investigations of heat transfer in phase change materials using non equilibrium model

... the temperature differences in PCMs without metal foams are much bigger than PCMs embedded into metal foams (about 10 times bigger than the ...times heat transfer performance of the case without metal ...

10

Design of Cascaded Oxide Thermoelectric Generator

Design of Cascaded Oxide Thermoelectric Generator

... have the highest ZT value of 1.64 at 1073 K (where ZT is a dimensionless figure of merit). And the ZT value is higher than one in the temperature range from 773 K to 1223 K; therefore, it has great potential in ...

6

XDEM for Tuning Lumped Models of Thermochemical Processes Involving Materials in the Powder State

XDEM for Tuning Lumped Models of Thermochemical Processes Involving Materials in the Powder State

... mean temperature during the thermogravimetric analysis (the slight underestimation of temperature from the lumped element model is due to the specific heat capacity, which is assumed constant and not ...

15

The development of thermotolerance protects blowfly flight muscle mitochondrial function from heat damage

The development of thermotolerance protects blowfly flight muscle mitochondrial function from heat damage

... heating. In the case of G3P respiration, acceptor control is restored to control levels, although the ADP:O ratio remains significantly lower. State III respiration rate is restored to about 90 % of that of controls. In ...

9

Effects of Ga Concentration, Heat Treatment and Deformation Temperature on Pseudoelasticity of Fe Ga Polycrystals

Effects of Ga Concentration, Heat Treatment and Deformation Temperature on Pseudoelasticity of Fe Ga Polycrystals

... unloading suggesting that the twinning pseudoelasticity rarely contributes to the strain recovery in Fe­20 at%Ga polycrystals at room temperature. In contrast, there exists fine {101} slip traces at 25 at%Ga (Fig. ...

7

Effect of Heat Treatment Conditions on the Properties of FePt Nanoparticles Produced by Sonochemistry

Effect of Heat Treatment Conditions on the Properties of FePt Nanoparticles Produced by Sonochemistry

... sonoelectrodeposition have been reported by Nam et al. [6]. In this study, we report the hard magnetic properties of FePt nanoparticles synthesized by sonochemistry, which was developed to make nanoparticles [7]. ...

6

The Effectiveness Of Using Phase Change Material (PCM) In Reducing Car Interior Temperature During Day-Time

The Effectiveness Of Using Phase Change Material (PCM) In Reducing Car Interior Temperature During Day-Time

... interior temperature by using paraffin ...high heat of fusion, negligible supercooling, low vapor pressure in the melt, chemically inert and stable, self-nucleating, and many ...

24

Show all 10000 documents...

Related subjects