High Impact Polystyrene
Mixed matrix membranes prepared from high impact polystyrene with dispersed TiO2 nanoparticles for gas separation
... environmental impact, high stability, low cost and ...considered. High impact polystyrene (HIPS) is a low cost and tough plastic material which in not investigated in the literature as ...
6
Effects of alkali treatments on the tensile properties of pineapple leaf fibre reinforced high impact polystyrene composites
... reinforced high impact polystyrene (HIPS) composite is presented in this ...fibre, high impact polystyrene, compatibilising agent, alkali ...
6
Fuel Oil Production from Two Stage Pyrolysis Catalytic Reforming of Brominated High Impact Polystyrene Using Zeolite and Iron Oxide Loaded Zeolite Catalysts
... when polystyrene or high impact polystyrene without flame retardants is pyrolyzed, styrene monomer is often obtained as the main oil component, which is mainly due to its characteristics of ...
11
Thermogravimetric analysis (TGA) and differential scanning calometric (DSC) analysis of pineapple leaf fibre (PALF) reinforced high impact polystyrene (HIPS) composites
... This paper studied the thermal behaviour of pineapple leaf fibre (PALF) reinforced high impact polystyrene (HIPS) composite. Thermogravimetric analysis (TGA) and differential scanning calorimetric ...
10
The Influence of Processing on the Aesthetic, Morphological and Mechanical Properties of Structural Foam Mouldings of High- Impact Polystyrene
... superior impact strength and metallization characteristics ...[15]. High-impact polystyrene (HIPS) features many of the ABS properties at a lower price and has a similar processing ...
9
Impact, thermal and biodegradation properties of high impact polystyrene/corn starch blends processed via melt extrusion
... so impact strength de- ...of impact strength due to decreasing ...because high impact polystyrene is resistant to impact, so the addition of materials like starch or glycerol ...
8
Effect of temperature, heating rate and zeolite-based catalysts on the pyrolysis of high impact polystyrene (HIPS) waste to produce fuel-like products
... of high impact polystyrene (HIPS) waste has been investigated under different process parameters, such as temperature, heating rate and types of zeolitic catalysts to produce valuable liquid ...of ...
10
Mechanical Properties of Sugar Palm Fibre Reinforced High Impact Polystyrene Composites
... SPF-reinforced high impact polystyrene composites were studied and in composites there was a complex interplay of the properties of the constituent phases such as matrix, fibre and interfacial region ...
6
The co-pyrolysis of flame retarded high impact polystyrene and polyolefins
... Figure 7 shows the concentration of each of the major components in the oil produced from the pyrolysis of Br-HIPS + polypropylene as measured on the GC-FID. Again it is obvious that styrene and alpha-methylstyrene are ...
23
Investigating the impact of cleaning treatments on polystyrene using SEM, AFM and ToF–SIMS
... An EUFP7-funded project entitled ‘Preservation of plastic artefacts in museum collections’ (POPART) [5], examined the effect of both dry and wet cleaning treat- ments on a range of plastics, including high ...
9
Wear and Hardness Characterization of Synthesized Polystyrene Composites
... morphological properties of polyester thermoplastic elastomer. The specimens of the composites with concentrations 5 to 40 weight % of mica were prepared by twin screw extrusion. They found that flexural strength and ...
8
An Experimental Study of Clay Brick using Polystyrene
... ‘Polystyrene’. Polystyrene beads are stable, low density foam, which consists of 98% of air and 2% of EPS ...brick. Polystyrene foam is, therefore, used as a pore forming material in the brick body ...
5
High impact = high statistical standards? Not necessarily so
... a high impact factor? Are there differences compared with articles published in journals with a somewhat lower impact factor that have adopted editorial policies to reduce the impact of ...
8
Colloidal crystals by electrospraying polystyrene nanofluids
... experimental setup. Polystyrene nanospheres, with 360-nm diameter, were typically electrosprayed using off-the-shelf nanofluids. Several parameters of the setup and deposition conditions were explored, namely the ...
8
Polystyrene as graphene film and 3D graphene
... manuscript, it has been shown that pyrolysis of polystyrene films or pellets form defective graphenes 458. either as films or as residues that can be dispersed in liquid media[r] ...
12
Study on Mechanical Properties of Expand Polystyrene
... Abstract: Expand Polystyrene is simply written as EPS, and it is newly used as a kind of embankment filler. Based on abroad studies to EPS mechanical properties, a further research on EPS has been done in this ...
5
Study and application of mortar with residues of Expanded Polystyrene
... The civil construction generates waste throughout its life, from the extraction of the used resources, the work implementation, until its demolition. It also has a very great amount of waste during the execution of the ...
6
Synthesis of Carbon Nanoparticles from Polystyrene Wastes
... of polystyrene) using the designed reactor and heat ...as high pressures and temperatures above 700 ºC are used along with appropriate catalysts for different periods, all of the materials lose their macro ...
5
Hybrid material based on sulfonated polystyrene and graphene
... of high-purity hydrogen, the reduction of the cost of the system and a variety of technological problems associated with low performance and low humidity ...and high hydrophilicity branch sulfonic acid ...
5
Characterization of Pectin Nanocoatings at Polystyrene and Titanium Surfaces
... of polystyrene [11,13, 16,17] and titanium surfaces ...non-coated polystyrene surfaces is caused by changes in the chemical composi- tion after coating with RG-Is ...the polystyrene surface was ...
9