• No results found

higher speed

Design of a decimation filter used in 
		digitizer for earthquake monitoring system with higher speed

Design of a decimation filter used in digitizer for earthquake monitoring system with higher speed

... Genetic algorithm [3] is using to reach optimal solutions for corresponding problem. The trouble here is computational complexity should be minimized with three points as the previous plan. Population of solutions must ...

5

RATIONALIZATION OF CURVES RESTRUCTURING PLAN AT HIGHER SPEED MOTION OF TRAINS

RATIONALIZATION OF CURVES RESTRUCTURING PLAN AT HIGHER SPEED MOTION OF TRAINS

... Моделювання процесу взаємодії рухомого складу і колії в кривих ділянках показав , що при врахуванні таких факторів як пружність ресорного підвішування , нерівностей на колії і колесах [r] ...

7

Design A High Throughput Vedic Multiplier Using Kogee-Stone Adder

Design A High Throughput Vedic Multiplier Using Kogee-Stone Adder

... Design of a high performance and high density multiplier is presented. This multiplier is constructed by using the kogee- stone adder. In previous we read about the designing of multipliers using the ripple carry adders ...

8

Analysis and Approach for Key Technique Based on THz Wireless Transmission

Analysis and Approach for Key Technique Based on THz Wireless Transmission

... Mbps speed. Even if reducing the transmission distance, the speed merely gets 500 ...the speed reaches a couple of hundreds Mbps because of its lower non-coherent reception sensitivity, high diffuse ...

7

Study of Audible Identification Alert System for Rash Driving

Study of Audible Identification Alert System for Rash Driving

... in speed indicator by putting Audible identification alert in vehicle, So when vehicle is running at higher speed on road, as speed increases beyond defined ...

5

Process Optimization of PCB Micro-Drilling Process

Process Optimization of PCB Micro-Drilling Process

... precision/high speed application for productivity ...with higher aspect ratios, and higher speed operation for micro hole drilling ...spindle speed and feed are chosen as machining ...

7

Studies on Mechanical and Dry sliding wear of 2014AlSiC composites produced by powder Metallurgy route

Studies on Mechanical and Dry sliding wear of 2014AlSiC composites produced by powder Metallurgy route

... a higher SiC ...sliding speed conditions. At a low speed wear rate, alloy with 5 vol% SiC was more than the alloy ...At higher speed the wear rate decreased with the increasing SiC ...

12

Analysis of Low Power High Speed Carry Skip Adder

Analysis of Low Power High Speed Carry Skip Adder

... their speed firmly influence the speed of processor ...a higher speed yet bring down vitality utilization contrasted and the customary one is ...The speed improvement is accomplished by ...

7

Design considerations for a recording instrument to be used in conjunction with R.I.T.'s radio astronomy system

Design considerations for a recording instrument to be used in conjunction with R.I.T.'s radio astronomy system

... recorder lower is speed higher speed there set stronger output playback speed be st any one it speed speed an at a to and periods tinuously is desired, the circuit has with if for faster[r] ...

26

Lower Speed Stability Analysis of Large Hybrid Differential Turntable

Lower Speed Stability Analysis of Large Hybrid Differential Turntable

... Turntable aims to make the workpiece fixed and supported, and follows the instructions from the controller to drive the workpiece rotational. The current large turntable mainly adopts a traditional way of pure ...

7

Mechanisms Controlling Friction and Adhesion at the Atomic Length-Scale

Mechanisms Controlling Friction and Adhesion at the Atomic Length-Scale

... assumed to be the same in both lateral and normal directions. Calibration of output volts from the PSD to nanometers was achieved by acquiring normal force versus z- displacement curves and determining the slope of the ...

196

Characterization of Acoustic Emissions from Journal Bearings for Fault
Detection

Characterization of Acoustic Emissions from Journal Bearings for Fault Detection

... 100% speed and the variation of lubricant viscosity of ISO VG 32, 48 and ...the higher viscosity of lubricant enables bearing to operate under better lubrication films, which leads to the smaller amplitude ...

13

SIMULATION OF MPC BASED SPEED CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR 
DRIVE

SIMULATION OF MPC BASED SPEED CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR DRIVE

... We modeled a campus network with an area 1 km x 1 km. Mobile nodes and the server were randomly assigned to the geographic area. In the simulations, the mobile nodes receive traffic from a common source (here ftp ...

10

Correlation between Microstructural Stability and Tensile Properties of FSWed Al Mg Mn Cast Plate during Subsequent Thermal Exposure

Correlation between Microstructural Stability and Tensile Properties of FSWed Al Mg Mn Cast Plate during Subsequent Thermal Exposure

... rotational speed that pertained to grain ...rotational speed of 850 rpm was an optimum FSWed condition for improving the tensile properties of WZ, which pertained to the better thermal ...

7

The Influence of Audio-Visual Cueing
(Traffic Light) on Dual Task Walking in
Healthy Older Adults and Older Adults
with Balance Impairments

The Influence of Audio-Visual Cueing (Traffic Light) on Dual Task Walking in Healthy Older Adults and Older Adults with Balance Impairments

... preferred speed, followed by two further walking tests, the order of which was randomly determined: dual task walking and dual task walking with a simulated traffic light ...

8

Lap Joint of A5083 Aluminum Alloy and SS400 Steel by Friction Stir Welding

Lap Joint of A5083 Aluminum Alloy and SS400 Steel by Friction Stir Welding

... The rotating tool made of JIS-SKH57 tool steel had a shoulder (20 mm diameter) with an unthreaded pin (5 mm diameter and 3.0–3.3 mm long). The tilt angle of the rotating tool with respect to Z-axis of the milling machine ...

7

Slow muscle power output of yellow  and silver phase European eels (Anguilla anguilla L ): changes in muscle performance prior to migration

Slow muscle power output of yellow and silver phase European eels (Anguilla anguilla L ): changes in muscle performance prior to migration

... A major determinant of power output is the cycle frequency at which the muscle operates. The maximum cycle frequencies at which eel slow muscle can produce positive power and the optimal frequencies for maximum power ...

11

Effect of Melt Spinning Variables on the Structural Changes of Recycled and Bottle Grade Filament Yarn PET

Effect of Melt Spinning Variables on the Structural Changes of Recycled and Bottle Grade Filament Yarn PET

... winding speed and spinning temperature in Table ...winding speed (P < ...to higher molecular weight of R- and BG-PET, which may assist better orientation during ...

9

Motor skill transfer in older adults

Motor skill transfer in older adults

... processing speed are of influence on the amount of transfer shown by older and younger adults is not supported by the ...a higher visuospatial working memory and/or a higher processing speed ...

27

Analysis of Driver Behaviour and Crash Characteristics during Adverse Weather Conditions

Analysis of Driver Behaviour and Crash Characteristics during Adverse Weather Conditions

... on speed of the vehicle, data collected from 21 samples were taken at different weather conditions on same road ...flyover speed we get as Standard deviation, mean of speed & mean square values ...

9

Show all 10000 documents...

Related subjects