Magnesium Alloy AZ31
Isochronal Annealing Behavior of Magnesium Alloy AZ31 after Hot Deformation
... hot-deformed magnesium alloy AZ31 were studied at temperatures of 373 to 673 K by optical and SEM/EBSD metallographic ...hot-deformed alloy had fine-grained structures developed by grain ...
7
Mechanical Properties of Magnesium Alloy AZ31 after Severe Plastic Deformation
... of magnesium alloy AZ31 was studied in multidirectional forging (MDF) under decreasing temperature ...forged alloy showed excellent higher strength as well as moderate ductility at room ...
7
Superplasticity of Fine Grained Magnesium Alloy AZ31 Processed by Multi Directional Forging
... Superplasticity was studied in a fine-grained magnesium alloy AZ31 processed by multidirectional forging (MDF) under decreasing temperature conditions. Tensile tests were carried out at temperatures ...
6
Degraded and osteogenic properties of coated magnesium alloy AZ31; an experimental study
... coated magnesium alloy is useful for tissue and bone repair and regeneration, such as but not limited to medical implant devices in orthopedic, craniofacial, dental, and cardiovascular surgeries ...[7]. ...
6
Dynamic Evolution of New Grains in Magnesium Alloy AZ31 during Hot Deformation*
... A commercially produced Mg alloy AZ31 was provided as a hot-extruded rod with a diameter of 19 mm. The chemical composition was as follows; Al 2.68, Zn 0.75, Mn 0.68, Cu 0.001, Si 0.003, Fe 0.003, and ...
7
The Corrosion Behavior of Magnesium Alloy AZ31 in Hot and Dry Atmospheric Environment in Turpan, China
... on AZ31 specimens after exposed in Turpan for three year was obtained with ...of magnesium was lower than 1 ...the AZ31 exposed for 12 and 24 ...
15
Plastic behaviour and forming limit during biaxial compressions of magnesium alloy AZ31 at room temperature
... Figure 6 shows the nominal stress-strain curves by uniaxial compressions. The compressive fracture occurred when d s n > 0 without any precursory phenomenon such as an area contraction, as seen also by the fractured ...
6
Microstructure and Mechanical Properties of Magnesium Alloy AZ31 Processed by Compound Channel Extrusion
... Mg alloy AZ31 of different processing ...the AZ31 alloy provided in the form of cast ingots is approximately 150 ...the AZ31 samples deformed at 623 K, 673 K and 723 K are determined to ...
6
Change Channel Angular Extrusion of Magnesium Alloy AZ31
... In this work, we proposed a modified ECAE process, change-channel angular extrusion (CCAE), in order to introduce even more severe plastic deformation so as to reduce the number of pass. We tested this CCAE technique on ...
6
Optimization of Die Material and Its Surface Coating for Press Forming Magnesium Alloy
... processing magnesium alloy is casting (thixomolding and die casting), 4) but it has serious problems including low yield and low production ...However, magnesium is a material which is fundamentally ...
5
In Vitro Characterization of Electrodeposited Hydroxyapatite Coatings on Titanium (Ti6AL4V) and Magnesium (AZ31) Alloys for Biomedical Application
... metals, magnesium and its alloys are found to have similar physiochemical characteristics to that of natural ...over magnesium alloys can limit the degradation and corrosion rates so as to make implants of ...
14
An Investigation of the Weld Current Characteristics on Twining and Tensile Strength of the AZ31 Alloy Sheet Joint Welded By GTAW
... of magnesium alloys AZ31 utilizing pulsed and alternative ...of magnesium alloys has some issues, and the most important of them is the issue of hot cracking [4], however, this issue is seldom stated ...
7
Evaluation of the Corrosion of AZ31 Magnesium Alloy Used as Sacrificial Anode for Cathodic Protection of Hot-Water Tank Storage Containing Chloride
... Magnesium alloy AZ31 was used in this work. The precise chemical composition was determined using inductively coupled plasma atomic emission spectroscopy (ICPAES) and is given in Table 1. Samples ...
16
Analysis of Explosively Welded Aluminum–AZ31 Magnesium Alloy Joints
... Magnesium alloy AZ31 and commercially pure Al A1100 were joined successfully using explosive welding technique. The geometry of the interfacial profile of the welds obtained under low kinetic energy ...
6
Some Characteristics of AZ31/AZ91 Dissimilar Magnesium Alloy Deposit by Friction Surfacing
... The surfacing efficiency was determined based on the assumption that the weight ratio of the consumable rod before and after surfacing is associated with the shape of deposit. The results of measurements of surfacing ...
5
Investigation on Dynamic Friction Properties of Extruded AZ31 Magnesium Alloy Using by Ring Upsetting Method
... for magnesium products is die-casting, that has some drawbacks such as less reliability and lower industrial productivity: an easy initiation of the some cast detects, difficulty in molding with thin wall, burr ...
6
Texture Randomization of AZ31 Magnesium Alloy Sheets for Improving the Cold Formability by a Combination of Rolling and High Temperature Annealing
... 3.4 Correlation between peak intensity and bendability Although the excellent formability of a randomized sample was exhibited by 90 degree V-bending test, a statistical correlation between the V-bending limit and the ...
7
Effect of Ca Addition on the Corrosion Resistance of Gravity Cast AZ31 Magnesium Alloy
... cast AZ31+xCa alloys as function of Ca ...of AZ31+xCa alloys increased with Ca content up to x ¼ 0:7, but decreased remarkably above 1 ...of AZ31+xCa alloy specimens after immersion ...cast ...
6
Effect of Anodizing Potential on the Surface Morphology and Corrosion Property of AZ31 Magnesium Alloy
... of AZ31 magnesium alloy after anodizing in 1 M NaOH solution at different anodizing ...of magnesium. Magnesium hydroxide and mag- nesium oxide peaks were also detected on the surface ...
5
Simultaneous Control of Shape and Properties of AZ31 Magnesium Alloy Sheets by Incremental Forming
... Experimental conditions for incremental forming are shown in Table 1. AZ31B-O magnesium alloy sheets were used for specimens. An optical micrograph of as received one is shown in Fig. 2, and the average ...
5