Mechanical Properties and Microstructures.
Investigation on Microstructures and Mechanical Properties of Extruded Biodegradable Zn 1Mg xZr (x = 0−0 4 %) Alloys
... element for the human body [20]. A small amount of Zr (<250 mg) in the human body also shows good biocompatibility and low toxicities [21]. Considering these aspects, it is of potential and fundamental interest to add ...
8
Effect of Post Weld Heat Treatment on Microstructures and Mechanical Properties of AZ31B Friction Welded Joint
... AZ31 magnesium alloy was welded by friction welding and the effect of post weld heat treatment on microstructures and mechanical properties were investigated. Fine grained microstructure whose minimum ...
9
Improvement of Microstructures and Mechanical Properties of Resistance Spot Welded DP600 Steel by Double Pulse Technology
... in microstructures during welding process dramatically affects the steels’ mechanical ...whose mechanical strength and performance significantly affect the safety and reliability of the automobile ...
8
Effect of Fe Addition on Microstructures and Mechanical Properties of Ni and C Free Co Cr Mo Alloys
... and mechanical properties of Ni- and C-free Co-Cr- Mo alloys for development of new biomaterials, and to find the substitute elements for Ni to increase the hot ...the microstructures and ...
5
Microstructures and Mechanical Properties in Friction Stir Zone of Thixo Molded AS41 Mg Alloy
... The friction stir weldability of thixo-molded AS41 Mg alloy was investigated, and the microstructures and mechanical properties in friction stir zones were examined and evaluated. The non-destructive ...
6
Detail investigation of microstructures and mechanical properties of Inconel 617 sheet of fiber laser welding
... attractive properties of components of power-generating plants, both fossils fuelled plants and nuclear power ...and mechanical properties was discussed in detail. Microstructures were ...
6
Effects of Coiling Temperature on the Microstructures, Mechanical Properties and Textures of 08Al Deep Drawing Steel Sheet
... Effects of the coiling temperature on the microstructures and mechanical properties of 08Al hot-rolled steel sheet were investigated. Meanwhile, cold rolling and annealing experimental veri fi cations ...
7
Microstructures, Textures and Mechanical Properties Evolution during Cold Drawing of Pure Mg
... chanical properties, microstructures and texture evolution of the as-drawn wires were investigated by tensile tests, transmission electron microscopy (TEM) and electron backscattering diffraction ...the ...
8
Effects of Nd on the Microstructures, Mechanical Properties and in Vitro Corrosion Behavior of Cast Mg 1Mn 2Zn xNd Alloys
... the microstructures, mechanical properties, in vitro corrosion behavior, and cytotoxicity of as-cast Mg- 1Mn-2Zn-xNd alloys (x = ...The microstructures were examined by X-ray diffraction ...
6
Evolution of Mechanical Properties and Microstructures with Equivalent Strain in Pure Fe Processed by High Pressure Torsion
... that the sample is in a form of disc and the size of the disc is generally limited to 10 mm in diameter in order to keep a high applied pressure. Because the strain is generated in proportion to the distance from the ...
7
Mechanical Properties and Microstructures of Locally Produced Aluminium Bronze Alloy
... The mechanical properties of the as-cast aluminium bronze sample with 0% deformation and no heat treat- ment are as shown in Figure 2(a) with its ultimate ten- sile strength being ...
7
Microstructures and Mechanical Properties of Austempering Cr Mo (SCM 435) Alloy Steel
... the mechanical properties of SCM435 bainite ...the mechanical properties of the specimen with austempering temperature 830°C for 25 min was better than that of 15 ...
5
Effect of Strontium Addition on the Microstructures and Mechanical Properties of Mg 5Al 3Ca Alloys
... Samples for metallography were etched in a solution of 4.2 g of picric acid, 10 ml of acetic acid, 10 ml of water, and 150 ml of ethanol. Microstructural observations of the alloys were made using optical microscopy, ...
5
Microstructures and Mechanical Properties of Pure V and Mo Processed by High Pressure Torsion
... the microstructures between V and Mo indicates that the effect of the applied pressure is different: it is little on V so that the microstructure including the grain size formed at 2 GPa is almost the same as the ...
8
Effects of Austenitising Conditions on the Microstructures and Mechanical Properties of Martensitic Steel with Dual Matrix Structure
... developing microstructures with fine distribution of ferrite and martensite in DP steel either by introducing new alloy design or adopting an appropriate heat treatment procedure [3, 6, ...
15
EFFECTS OF DEFORMATION AND ANNEALING TEMPERATURE ON THE MICROSTRUCTURES AND MECHANICAL PROPERTIES OF CU-32%ZN BRASS
... This research studied the deformation behaviour of Cu-32% Zn alloy at various degree of cold reduction, as well as the change of microstructures after subsequent annealing process. It was intended to understand ...
5
Effects of Zirconium Addition on Microstructures and Mechanical Properties of Co 29Cr 6Mo Alloy
... suppresses the segregation of harmful impurity at grain boundaries. It can be thought that Zr has a similar effect on the Co-based alloys. This is why the yield of Zr amount is much smaller than the addition in this ...
5
The Effect of Solidification Rate on Morphology Microstructures and Mechanical Properties of 80%Cu-20%Sn Bronze Alloys
... Tensile and hardness measurement results The effect of solidification rate on the mechanical properties such as the tensile and hardness are given on table 1 and Fig 10 respectively. The ultimate strength ...
8
The effect of heat treatment on the microstructures and mechanical properties of copper alloy
... Heat treatment is described as the controlled heating and cooling methods performed on a material in a solid state in order to alter the characteristic of microstructure and its properties. Heat treatment can be ...
24
Effect of heat treatment on the microstructures and mechanical properties of high carbon steel
... First of all I am grateful to Allah S.W.T for giving blessing and strong spirit for me to complete my Project Sarjana Muda. I would like to offer my deepest gratitude to Mr. Ridhwan bin Jumaidin from the bottom of heart ...
24