Numerical (ANSYS).
Determination of Optimum Domain Size for 3D Numerical Simulation in ANSYS CFX
... 3D numerical study of wind load on a cube shaped building is carried out to determine domain size required for optimum ...results. Numerical simulation is carried out in ANSYS CFX package with ...
9
Numerical Simulation of Flow and Determination of Aerodynamic Forces in the Balanced Control Valve
... Using numerical simulation performed by the ANSYS/FLUENT system, flow patterns were obtained from steam flow in a balanced control valve. The course of flow showed non-stationary flow at certain travel ...
6
Behavior of Filled and Encased Composite Column Using 3D Numerical Modelling ANSYS
... Three dimensional FE models of steel column structures have been well verified with previous experimental results. More recent studies using FE modeling have focused mostly on encased column structures. Debski (2013), Li ...
6
Numerical Analysis of Strength Behaviour of Bolted Steel Beam Column Connection Based on Type and Position of Stiffeners
... paper, Numerical analysis of bolted steel beam-column connections based on type and position of stiffener plates were done by means of a finite element model using the ANSYS ...
7
Numerical simulation of axisymmetric valve operation for different outer cone angle
... Numerical simulation was done in ANSYS Fluent 16. It was used simulation without gravity with standard k- viscous model with enhanced wall treatment, and with automatic model constants. It was used SIMPLE ...
6
SST are employed in ANSYS FLUENT and the numerical results
... in ANSYS FLUENT and the numerical results validated against XFLR5 (a semi-empirical software based on Massachusetts Institute of Technology’s famous low Reynolds number CFD program, ...to ANSYS ...
6
NUMERICAL MODELING VALIDATION OF REINFORCED CONCRETE SLABS UNDER HIGH-MASS LOW-VELOCITY IMPACT USING ANSYS WORKBENCH EXPLICIT DYNAMICS SYSTEM.
... loading. ANSYS Workbench V.17.0 commercial software has been used in the numerical modeling and simulation of the dynamic problem using the Explicit Dynamics ...proposed numerical model has been ...
19
Experimental and numerical investigation the effect of mass flow rate on the heat transfer flat plate solar collector with using nano fluid
... A solar collector is the major componentof a solar water heating system. The heat energy from the solar radiation was utilized in the flat-plate solar collector can be enhanced by using nanofluid. This work investigates ...
8
Numerical Study of the Cross Sectional Shape of Tunnel under Blast Effect using ANSYS
... and numerical analyses of long carbon fiber reinforced concrete panels exposed to blast loading”, International Journal of Impact Engineering, 57, 70-80 (2013) ...
5
Numerical Analysis of Three-Lobe Hydrodynamic Journal Bearing using ANSYS
... [3] J. Moradi Cheqamahi, M. Nili-Ahmadabadi, S. Akbarzadeh developed the dynamic mesh method to solve the conservation equations of mass, momentum and energy. According to authors the main disadvantage of many analytical ...
12
NUMERICAL INVESTIGATION OF STEEL GRADE CHANGE USING ANSYS
... These numerical modeling involves number of ...the numerical (CFD) ...Hence numerical simulation helps in changing the design parameters and test the performance ...
6
Determination of nugget size in resistance projection welding: numerical method with experimental measurements
... A two-dimensional axisymmetric model is carried out through the ANSYS finite element package [32]. The finite element mesh contains two types of 2D elements including PLANE42, containing two degrees of freedom as ...
33
Numerical Analysis of Solar Roadways using ANSYS
... Abstract: Today there are more consequences in climate change due to over utilization of fossil fuels thus leading to serious impact on environment. So there is a need for an alternative solution to reduce the ...
6
A numerical study of SCF convergence using ANSYS
... This command will generate 10 elements on the assigned line with a scaling factor of 3, i.e. the elements at the near end of ellipse will be 3 times as small as the element at the far end on the same line. This procedure ...
6
Capacity Analysis of Post Tensioned Steel Structure in Column Removal
... a 9n order to validate these Finite Element models using a relevant benchmark of experimental data that is available in the literature point of view. The role of different structural elements which facilitate the load ...
6
SIMULATION OF CUP DRAWING BY DIFFERENT METHODS
... Abstract: The prediction of optimized forming parameters viz. the punch force, blank holding force, forming factor, and hydrostatic pressure will contribute to cost reduction of the processed metal through curtailment in ...
11
Grid generation methodology and CFD simulations in sliding vane compressors and expanders
... and numerical studies on a micro ORC sliding vane expander with circular stator and radial inlet and outlet ports [6] while Montenegro et ...were ANSYS CFX and OpenFOAM ...or ANSYS there are ...
11
Output-only identification of rigid body motions of floating structures : a case study
... The structure considered in this work is a spar floating support for offshore wind turbines, inspired to the OC3- Hywind spar buoy [8], but simplified to meet the linearity requirement of the method. The spar support is ...
6
THE AIR FLOW INFLUENCE ON THE DRAG FORCE OF A SPORTS CAR
... the numerical analysis of the drag force generated on the body of a sports car, based on the CFD method in the Ansys Fluent ...Keywords: numerical analysis, CFD, drag force, car body, sports ...
7
Strengthening of Partially Damaged Deficient RC Beam with Externally Bonded BFRP Composites using FEA
... of numerical models helps in developing a good understanding of the behavior and to carry out parametric studies at lower ...presents numerical results on strengthening of shear deficient RC beam by ...
6