Nylon 66
Optimizing the impact resistance of high tenacity Nylon 66 weft knitted fabrics via genetic algorithm
... The aim of the present research is evaluating the impact resistance of weft knitted fabrics which are knitted in basic patterns from the high tenacity Nylon 66. The woven fabrics have been applied for ...
11
Electron Beam Irradiation of Nylon 66: Characterization by IR Spectroscopy and Viscosity Studies
... on nylon 66 and e-beam irradiated nylon 66 were carried out by measuring the solution viscosity and FTIR spectroscopic ...of nylon 66 resulted in the formation of insoluble ...
9
Optimization of shrinkage in injection-molding of 40% glass filled nylon 66 using response surface methodology (RSM) and genetic algorithm (GA)
... The selected factors for machining parameter and the factorial levels taken from the processing guides of Nylon 66 with 40% Glass Filled material [11][12] and the linked processing parameters according to ...
6
Variations in refractive optical properties of nylon 66 fibres under different thermal conditions
... Plate 2 shows microinterferograms of the multiple-beam Fizeau fringes observed in the transmitted light in the case when the nylon 66 fibres have been heated in the water (the constant temperature 80ºC, and ...
9
Introduction of Nylon-66 on Side Arm in a Catheter Manufacturing Process
... for Nylon-66 shown in ...addition, Nylon 66 is regarded as a suitable material for medical ...that Nylon 66 were needed to be used under special circumstances in medical fracture ...
5
Thermal analysis of joining Nylon 66 composites using microwave irradiations
... The potential benefits of the technology will speed up the replacement of thermosetting resins by advanced thermoplastic composites in the structural parts of aeronautical, military and recreational industries. The ...
24
Design and material analysis of belt shifter assembly for enhancing the belt life with legato movement of over head travelling cleaner
... Welding Nylon 66- Part II Finite Element Journal of Thermoplastic Composite Materials, 211 ...Oriented Nylon 6 - Volume 12 issues per year- ...
5
Extraction of Natural Dyes for Textile Dyeing from the By-Products of the Timber Industry
... The timber industry releases considerable amount of wastes which contain natural dyes. Such wastes could serve as sources for the extraction of natural dyes for textile dyeing operations. The extraction of various shades ...
6
Recovery of Monomer from Nylon waste powder for its Recycling
... The nylon waste in the form of nylon rope were procured and crushed into fine powder after deep freezing it to increase its brittleness similarly Nylon-66 were specially ordered for this ...
6
Processing of polymer matrix composites using variable frequency microwave (VFM)
... region. Nylon 66/GF (33%) specimens with the same lap area and surface treatment were located in a standard rectangular waveguide as depicted in Figure 4 (Ku et al, 1997a; Siores and Groombridge, ...
9
Dis-Azo Dyes Derived From 2-Methoxy-5-Nitroaniline and 3-Chloroaniline and Their Application on olymer Fibres
... The results of the light fastness (Table 2) showed that all the dyes gave good light fastness on polyester and nylon 66 fabrics except dye 5e with ratings of 5 to 6. The good light fastness is due to the ...
8
Detection and enumeration of toxin producing Pasteurella multocida with a colony blot assay
... A Peroxidase-labeled MAb detection of toxin-producing strain P-4533B colonies grown for 16 h on blood agar and transfered to a nylon 66 membrane; P-4533B colonies were in a mixed culture[r] ...
5
Recycling of constructional plastics with additives of exhausted polyethylene
... It’s developed new polymeric-composite materials with the use of wasted exhausted polyethylene РЕ500 and РЕ-1000 models adding to polymer composites UPA-6-30 and Nylon 66, in which equal[r] ...
10
Variable frequency microwave (VFM) processing facilities and application in processing thermoplastic matrix composites
... facilities using a power level of 400 W. Similarly, at an exposure time of 55 seconds, the bond strength using VFM was 1050 N, which was 9 % higher than that procured from its rival operating at 240 W. Figure 9 shows ...
27
Thermal analysis comparison between three random glass fibre-reinforced thermoplastic matrix composites bonded by adhesives using microwaves
... reinforced Nylon 66, the peak lap shear strengths obtained at exposure times of 35 and 55 seconds for the power levels of 400 W and 240 W respectively are depicted in Figure ...
24
Variable frequency microwave processing of thermoplastic composites
... With glass fibre reinforced nylon 66, the peak bond strengths obtained were at exposure times of 35 and 55 seconds with power levels of 400 W and 240 W respectively. They were 32% and 28% respectively ...
27
Bioinspired Aryldiazonium Carbohydrate Coatings: Reduced Adhesion of Foulants at Polymer and Stainless Steel Surfaces in a Marine Environment
... that find applications in marine settings: stainless steel 316 (SS316), nylon-6 (N-6), and poly(ether sulfone) (PES). Saccharides were immobilized via aryldiazonium chemistry; SS316 and N-6 samples were subjected ...
48
Single-Component Nylon-6 Composites.
... This type of self-reinforced composite would be produced by making the reinforcing component from the same polymer as the matrix, but with the constituent polymer chains in the reinfor[r] ...
74
Ecofriendly” synthesis, characterization and dyeing of azo based acid dyes on nylon fabrics
... The wash fastness of the dyed fabrics is another important property desired off. The dyed textile materials are very often washed with soap and detergents and become necessary that the color should not fade on washing. ...
6
In situ Polymerization of Multi Walled Carbon Nanotube/Nylon 6 Nanocomposites and Their Electrospun Nanofibers
... Figure 7a and b shows the WAXS patterns of the nanofi- bers and films respectively. The films were made by hot- pressing the pellets between two aluminum plates and then quenching them in icy water. Nylon-6 ...
8