Parameters used in the pulsed-dispenser mode
Study of the parameters influencing the thermal performances of an earth to air heat exchanger used in cooling mode
... ARTICLE INFO ABSTRACT The geothermic low temperature can be used to produce the fresh air with the help of an adequate heat exchanger. This last one is often constructed from a pipe in PVC buried in soil and in ...
9
EVALUATION THE EFFICACY OF PULSED RADIOFREQUENCY ( PULSED DOSE MODE) FOR THORACIC POST HERPETIC NEURALGIA TREATMENT
... were used in treatment of pain like nerve blocks , subarachnoid injection of local anesthetics, removal of the affected skin and neuromodulation techniques (8) Pulsed radiofrequency ( PRF) is a different ...
7
Effect of Waveform Parameters on Pulsed Glow Discharge in Air
... electric field. 2. Experimental Set-Up Figure 1 shows the schematic experimental circuit em- ployed in this research. A single pulse with the pulse risetime from 10 ns to 500 ns, pulse width from 100 ns to 2 µs, peak ...
5
Measurements of Electro-magnetic Parameters in Pulsed Power Systems
... be used advantageously depending upon the material in use ...be used in either mode while crystal like Lithium Niobate are mainly used in transverse ...
5
Generation of Pulsed Fe Plasma and Study of Its Physical Parameters
... Laser produced plasma has high temperature and high electron density gradient, this plasma is also high irradiative, it’s emitted a spectrum deepening on the target, the emitted spectrum gives information about the ...
7
Dropout dynamics in pulsed quantum dot lasers due to mode jumping
... In a conventional semiconductor laser, the phase- amplitude coupling is characterized by the afactor. 16 Its impact on laser performance has been a subject of intensive research for decades. Measurements of the afactor ...
6
Mixed-mode S-parameters and Conversion Techniques
... 2. Differential Signal Differential signaling is a signal transmission method where the transmitting signal is sent in pairs with the same amplitude but with mutual opposite phases. The main advantage with the ...
13
Could the super-pulsed CO2 laser be used for oral excisional biopsies?
... samples. The parameters were a power of 4.2 W in focused mode and a frequency of 80 Hz in super-pulse mode. The histological analysis was performed with an optical microscope. Computerized imaging ...
5
The Effects of Pulsed Current Parameters on Porosity of Copper Prepared by Jet Electrodeposition
... 2. EXPERIMENTAL The jet electrodeposition experimental setup (Fig. 2) consists mainly of an NC-controlled framework, nozzle and pulsed current power supply. A copper rod was placed in the anode chamber as the ...
10
Effect of deposition parameters on TiAlN coating using pulsed DC CFUBMS
... CFUBMS, Pulsed DC, Coating, Machining Introduction < PVD coated tools are preferred to CVD coated tools due to lower deposition temperature, better compositional control of coating and minimisation of the thermal ...
10
Investigation of Effective Parameters on Pulsed Nd:YAG Passive Q-Switched Laser
... For this reason we have used the Nd:YAG rod with diameter of d=5mm instead of 4 mm. In this case due to high heat generation we have water cooled the rod. In this stage we have repeated the experiment as explained ...
8
Procedure of Calculating the Parameters of the Inter-Pulse Period in Pulsed Arc Welding
... the parameters of the inter-pulse period such as current strength, electrode supply speed and time length is presented in the ...period parameters, influencing on the temperature of the electrode in the ...
8
The effect of pulsed electrodeposition parameters on the microstructure and magnetic properties of the CoNi nanowires
... obtain highly ordered pores, a two-step anodization process was employed. In the first step, anodizing of sample was performed in the 0.3 M oxalicacid solution at 40V and 17 º C for about 10 h. Wet chemical etching by ...
7
Highly Energy-Efficient On-Chip Pulsed-Current-Mode Transmission Line Interconnect
... 4.2 Discussions First, let us compare our interconnects with the conventional on-chip transmission line inter- connects (TLIs). As has been discussed in Section 1, the CML (current-mode logic) or LVDS (low-voltage ...
22
PROCEEDINGS OF SPIE. Pulsed power L-band magnetron with increased operating parameters
... today, used for both commercial and military purposes, are based on constructions developed many years ...their parameters were sufficient for the target ...operating mode than the basic mode, ...
10
Adaptive sliding mode control of the A-axis used for blisk manufacturing
... is used to replace the sensor and an ASMC system is constructed, 24 as illustrated in ...is used to estimate the state variables and the unknown system model and an adaptive law is used to estimate ...
8
Configuration of the Sentry firmware parameters used in the Bluetooth solution.
... Discoverability of the Bluetooth ® Module The Bluetooth ® module communicates with the CDU to establish a secure Bluetooth connection that makes CDU operational data available for viewing. The module has a pushbutton on ...
27
An Attack on CFB Mode Encryption As Used By OpenPGP
... This is a much less likely scenario than in the previous section. In this situation it is more likely that information on errors (including decryption errors) will be returned to the requester, which in this case could ...
10
Listino prezzi / Price list 2011 Linea Dispenser / Dispenser Line
... Euromop, società del gruppo IPC, nasce nel 1980 ed è oggi leader mondiale nella progettazione e nella produzione di attrezzature per la pulizia professionale. È la qualità del suo reparto di ricerca e sviluppo che ha ...
16
Smart Medication Dispenser
... II. PAST METHODOLOGY In recent years with development in electronic communication systems, many devices and software applications are available that helps in complicated drug management. Out of them, most convenient ones ...
5