pipe length
A review of literature for the structural assessment of mitred bends
... This paper presents a state-of-the-art review of literature available for the structural assessment of all types of mitred pipe bends. Compared with smooth bends, the volume of literature available for mitres is ...
29
Design of Experimentation for Developed Hydraulic Ram pump
... of pipe fittings of suitable designed ...suction pipe, Length of suction pipe, Diameter of flapper waste valve(bronze),Dimensions of non-returning valve(NCL ball type),Diameter of air column, ...
7
Pressure Surge Dependence on Valve Operations in a Pipeline Loading System
... of the system rises such that can destroy the pipeline mechanically, while at slower valve closure rate, there is high tendency of vacuum separation in the system due to a remarkable fall in the pressure of the system. ...
9
Mechanical Structure Design Features of the KALIMER-600 Sodium-Cooled Fast Reactor
... The IHTS piping system of KALIMER-600 connects IHX, steam generator and secondary EMP. The piping material is Mod.9Cr-1Mo, which has a low thermal expansion and a high ultimate strength. The shortening of the IHTS piping ...
7
A report on increasing the thrust of a turbojet engine by combustion of fuel in the tail pipe
... Any increase in tail pipe length will increase the time available for combustion, subsequent heat distribution, and stream mixing, thus improving the heat addition efficiency, with conse[r] ...
55
Optimisation of a Capsule Transporting Pipeline Carrying Spherical Capsules
... Commercial CFD package FLUENT has been used to obtain the pressure drop in the capsule carrying pipeline. A hydrodynamically smooth (i.e. ε/D = 0) test section similar to that of Ulusarslan and Teke [2] has been ...
7
The Methodology For The CFD Investigations In The Exhaust Gas Manifold Pipe Of A Single Cylinder Spark Ignition Engine To Improve Its Performance
... The computational methodology was started by writing conservation equations for a control volume in the partial differential form because of the involvement of more than one variable. Starting from the fundamental ...
16
A molecular communication link for monitoring in confined environments
... This conclusion can be visualized by the 3D plots of radio and molecular performance as a function of the number of pipe bends and the overall pipe length. In Fig. 4, the plot shows how the signal ...
12
Flow Velocity and Crack Angle Effect on Vibration and Flow Characterization for Pipe Induce Vibration
... the pipe is effect on the vibration of the pipe and it is effect on the pipe ...The pipe frequency is therefore dependent on the velocity and properties of the liquid flow through the ...of ...
9
HEAT PIPE AN ENERGY RECOVRY SYSTEM- A REVIEW PAPER
... heat pipe is a heat-transfer device that combines the principles of both conductivity and phase transition to efficiently manage the transfer of heat between two solid ...heat pipe a liquid in contact with ...
8
Optimization of operating parameters of earth air tunnel heat exchanger for space cooling: Taguchi method approach
... temperature, pipe diameter and length, burial pipe depth, soil thermal conductivity, air flow velocity, ...i.e., pipe diameter, pipe length, air velocity, and inlet air ...
17
Multi pipe Routing in Bundles for Aero engine using MOPSO
... bundled pipe routing method for aero-engine based on Multi-Objective Particle Swarm Optimization (MOPSO) is ...reference pipe is selected as particle encoding, and the coordinates of other pipe nodes ...
7
Comparison Study of Effective Length Method (ELM) and Direct Analysis Method (DAM) for Piperack Sabade Madhuri, Prof. A.A.Hamane
... The model was analyzed with a pinned base along major axis and fixed along minor axis column. The member sizes were chosen without regard to serviceability and picked only to satisfy the load demand. Effective ...
6
Using interior point optimization technique for mufflers cost reduction
... Perforated mufflers can be modeled by the segmentation approach [1] by modeling a perforated pipe passing through a muffler cavity as four port element. Elnady and Åbom [2] used the two-port transfer matrix method ...
7
An Analytical Study on the Effects of End Conditions on the Behavior of 45- and 90-Degree Elbows Subjected to Bending
... or pipe bend of hollow circular cross section ...or pipe bend subjected to seismic accelerations, which are represented by equivalent body forces, X, Y, and Z, acting in arbitrary directions ...or ...
8
Fatigue studies on stainless steel piping materials and components: Indian AHWR
... the pipe subjected to block loading (increasing stress ratio followed by decreasing stress ratio), intermittent overloading and underloading is also decreased compared to that of constant amplitude ...
8
Studies of the damaging effect at various loads and hydrostatic test frequencies
... The re-testing interval should not exceed the time for which the defects which can withstand the test pressure and remain in a pipeline after testing will enlarge during the cyclic change of operating pressure or due to ...
9
Design and Analysis of Pipe Rack System using STAAD PRO V8i Software
... unit. Pipe racks are main artery of the Oil & Gas Plants and hence detail planning and study are essential for any industrial ...The Pipe racks have to be designed for majority of the loads like primary ...
14
Heat Pipe for Aerospace Applications—An Overview
... The recent development of nanofluids, or fluids consisting of a conventional heat transfer base with nanome- ter-sized oxide or metallic particles suspended within, offers the exciting possibility of increased heat ...
14
Extending the persistent primary variable algorithm to simulate non-isothermal two-phase two-component flow with phase change phenomena
... 5, the heat pipe was represented by a 2D horizontal column (2.25 m in length and 0.2 m in diameter) of porous media, which was partially saturated with a liquid phase saturation value of[r] ...
23